Epson Projector Powerlite 1220 User Manual

							Presenting With the Remote Control61
Presenting a Slideshow 
(PowerLite 1220/PowerLite 1260 
Only)
You can use your projector’s Slideshow feature whenever you connect 
a USB device that contains .JPG image files. This lets you quickly and 
easily display individual images, or start a slideshow of all the images 
in a folder. You can control your slideshow using the projector remote 
control.
For an instant PowerPoint presentation, convert your PowerPoint 
slides to individual .JPG files (save as *.jpg) and store them in a folder. 
Copy that folder to a USB flash memory drive (thumb drive), or other 
USB device. Then connect the device to the projector and begin your 
presentation.
You can switch the display from the device displaying the slideshow to 
another source using the 
Source Search button or one of the specific 
Source buttons on the remote control. To return to the Slideshow 
source, press 
Source Search and select USB, or simply press the 
USB button.
Starting a Slideshow
1. Connect a USB device to the projector’s USB TypeA port (see 
page 42).
2. If you are connected to another image source, press the 
USB 
button on the remote control to go to the Slideshow program.
note
You can project .JPG files in 
resolutions up to 
8176 × 6144, with pixel 
counts incrementing in 
multiples of 8.
If a .JPG file is highly 
compressed, your projector 
may not be able to display it 
correctly. The projector can’t 
display progressive .JPG 
files.
You cannot project movie 
files using the Slideshow 
feature. 
						

							62Presenting With the Remote ControlIf you are not connected to another image source, the Slideshow 
program appears automatically.
If necessary, press the arrow buttons on the remote control to 
highlight the device you want to present from, then press the 
Enter button.
3. If you need to select a subfolder on your device, press the arrow 
buttons to highlight the folder and press 
Enter. 
4. To display an individual image, press the arrow buttons to 
highlight it and press 
Enter. To display additional image files, 
press the l or r arrow button.
5. To display a slideshow of all the images in the current folder, use 
the arrow buttons to highlight 
Slideshow on the bottom of the 
Slideshow screen and press 
Enter. The images display sequentially 
one time through. At the end, you see the folder display again.
Select the following as necessary to control your display or slideshow:
■To move back up a folder level, highlight Back to Top at the top 
of the Slideshow screen and press 
Enter.
■To select a different device, highlight Select drive in the upper 
right corner of the screen, press 
Enter, and select the device.
note
To rotate a displayed image, 
press the u or d button on 
the remote control until it is 
displayed correctly.
note
To display a slideshow from 
a folder that is not open, 
highlight the folder and press 
the 
Esc button on the 
remote control. Then select 
Slideshow from the menu 
that appears and press 
Enter.
To begin a slideshow from a 
particular image, use the 
arrow buttons to highlight 
that image, press 
Enter, 
then press Enter again.  
						

							Presenting With the Remote Control63
■If all the images in a folder do not fit on the Slideshow screen, 
highlight 
Next page at the bottom of the screen and press Enter 
to display the next screen full of images. Select 
Previous page at 
the top of the screen to select the previous screen.
■To exit the slideshow, press Esc, select Exit, and press Enter.
Selecting Slideshow Display Options
To select slideshow options or add special effects, follow these steps:
1. Highlight 
Option at the bottom left corner of the slideshow 
screen and press 
Enter. You see this screen:
2. Highlight the options you want to use, and press 
Enter. 
Option Available settings
Display 
orderName order displays files in name order
Date order displays files in date order
Sort orderIn Ascending sorts the files first to last
In Descending sorts the files last to first
Continuous 
playOn displays a slideshow continuously
Off displays a slideshow one time through 
						

							64Presenting With the Remote Control3. When you are finished, highlight 
OK at the bottom of the screen 
and press 
Enter. (Highlight Cancel and press Enter to cancel 
your changes.)
Screen 
switching 
timeNo does not switch file display automatically
1Sec. to 60Sec. displays files for the selected time 
and switches them automatically
EffectWipe transitions between images with a wipe effect
Dissolve transitions between images with a dissolve 
effect
Random transitions between images using a variety 
of effects in random order Option Available settings 
						

							65
4
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image, 
sound, and other features. This chapter covers the following 
information:
■Using the menu system
■Adjusting the image
■Adjusting signal settings
■Customizing projector features
■Customizing power and operation
■Using the projector security features 
						

							66Fine-Tuning the Projector
Using the Menu System
You can use the remote control or the projector’s control panel to 
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the 
Menu button on the 
remote control or on the projector. You see a menu screen similar 
to the one below: 
The menus are listed on the left and the options available for the 
highlighted menu are shown on the right.
2. Use the arrow buttons on the remote control or the projector to 
scroll through the menu list. When you’ve highlighted the desired 
menu, press the 
Enter button to select it. 
3. Once you’ve selected the menu, use the arrow buttons to scroll 
through the list of options. (Some of the options may be grayed 
out or unavailable, depending on the selected source.)
4. After highlighting the option you want to adjust, use the arrow 
buttons to change the setting. In some cases, you may have to 
press the 
Enter button to view a sub-screen. 
■Press the left or right arrow button to adjust a slider bar.
■To select from two or more settings, press the up or down 
arrow button to highlight the setting and press 
Enter. 
5. After changing the settings, press the 
Esc button to save your 
changes and return to the previous menu (or press it again to exit 
the menu system). You can also press the 
Menu button to exit. 
Menu list
Options 
						

							Fine-Tuning the Projector67
Restoring the Default Settings
You can use the Reset option on any menu to restore the 
factory-default settings for the settings in that menu.
To restore all the projector settings to their factory-default values, 
select the 
Reset menu, highlight Reset All, press Enter, and select 
Yes to confirm.
Adjusting the Image
You can use the Image menu to adjust the brightness, sharpness, color, 
tint, contrast, and 
Auto Iris settings.
1. Press the 
Menu button on the projector or remote control and 
select the 
Image menu. You see a screen similar to one of these:
note
When you select Reset All 
in the Reset menu, it does 
not reset the Input Signal, 
User’s Logo, Language, or 
Lamp Hours settings.
note
If you are using the HDMI 
port (PowerLite 1220/
PowerLite 1260 only), you 
see the menu on the left if 
the signal is digital RGB 
video, or the menu on the 
right if the signal is 
component video.
Component video/ Composite video/ 
S-Video
* PowerLite 1220/PowerLite 1260 only
Computer/USB display/ RGB video/ 
USB* 
						

							68Fine-Tuning the Projector2. Adjust the desired options as needed:
■Color Mode
Lets you quickly adjust the color and brightness for various 
environments. You can save a different setting for each 
source. See page 52 for a description of each color mode.
■Brightness 
Lightens or darkens the overall image. 
■Contrast
Adjusts the difference between light and dark areas. 
■Color Saturation
Adjusts the color depth of the image. 
■Tint
Adjusts the balance of green to magenta in the image. 
■Sharpness
Adjusts the sharpness of the image. 
■Color Temp.
Sets the color temperature of the image. Select High to tint 
the image bluer or 
Low to tint it redder (default setting is 
Medium). (Not available if sRGB is selected as the Color 
Mode setting.) 
■Color Adjustment
Adjusts the color values. Select Red, Green, Blue to adjust 
red, green, and blue hue and saturation values. (Not available 
if 
sRGB is selected as the Color Mode setting.)
■Auto Iris
Automatically adjusts the projected luminance according to 
the brightness of the image. (Available only when 
Dynamic 
or Theater is selected as the Color Mode for the current 
input source.)
note
The available settings vary 
depending on the input 
source selected.
The 
Brightness setting 
changes the opacity of the 
projector’s LCD panels. You 
can also change the lamp’s 
brightness. Select 
Power 
Consumption 
in the 
Settings menu, then choose 
Normal or ECO (the 
default setting is Normal). 
						

							Fine-Tuning the Projector69
Adjusting Signal Settings
Although the projector normally detects and optimizes the input 
signal automatically, you can use the Signal menu to make manual 
adjustments. In addition to changing the position of the projected 
image, you can correct tracking and sync for computer images, or 
change the aspect ratio. 
1. Press the 
Menu button and select the Signal menu. You see a 
screen similar to one of those below. (The settings will be different 
depending on the source you are projecting from.)
Computer/RGB video Component video
Composite video/S-Video HDMI (PowerLite 1220/ 
PowerLite 1260 only) 
						

							70Fine-Tuning the Projector2. Adjust the desired options as needed:
■Auto Setup 
Leave this setting 
On to automatically optimize computer 
images. Turn it off if you want to save adjustments you have 
made to the Tracking, Sync, and Position settings.
■Resolution
Set to Auto to have the projector automatically identify the 
resolution of the input signal. If necessary, select 
Wide (for 
widescreen images) or 
Normal (for 4:3 ratio images).
■Tracking
Adjust this value to eliminate vertical stripes in computer 
images.
■Sync
Adjust this value if computer images appear blurry or flicker.
■Position
If the image is slightly cut off on one or more sides, it may not 
be centered exactly. Select this setting and use the arrow 
buttons to center it.
■Progressive
For composite video, S-Video, component video, and certain 
signals from the HDMI port only (PowerLite 1220/
PowerLite 1260 only). Turn this setting on to convert 
interlaced signals into progressive signals (best for moving 
images). Leave the setting 
Off for still images.
■HDMI Video Range (PowerLite 1220/PowerLite 1260 only)
When you connect to the HDMI input port, set the 
projector’s video range to match the video range setting of 
your device.
■Input Signal
If the colors don’t look right on the Auto setting, select the 
setting for the type of equipment you’ve connected to the 
Computer (Component Video) port. Choose RGB for a 
computer or RGB-video connection, or 
Auto for a video 
device that outputs a component video signal (with 
connectors labeled Y/Cb/Cr or Y/Pb/Pr).
note
You can also use the remote 
control’s 
Auto button to 
automatically reset the 
projector’s Tracking, Sync, 
and Position settings. See 
page 99 for details.
note
You can adjust the 
Progressive setting for 
signals from the HDMI 
input port (excluding digital 
RGB) or component video 
only when 480i/576i/1080i 
signals are being input 
(PowerLite 1220/
PowerLite 1260 only).
The HDMI Video Range 
setting cannot be set for 
digital RGB signals 
(PowerLite 1220/
PowerLite 1260 only).