Epson Projector L1300U User Manual

							91
2. Press the
Lensbutton on the control panel repeatedly until the focus adjustment screen appears, or
press the Focusbutton on the remote control.
3. Press and hold the arrow buttons on the projectors control panel or remote control to adjust the focus.
4. Press the Escbutton on the projectors control panel or remote control when finished.
Focusing the Image with an Optional Short Throw Lens
Parent topic: Using Basic Projector Features
Related tasks
Focusing the Image with an Optional Short Throw Lens
Focusing the Image with an Optional Short Throw Lens If you installed an optional short throw lens (ELPLX01/ELPLU03/ELPLU04/ELPLW05/ELPLU02), you
may need to focus on the center of your screen and then correct any distortion in the surrounding area.
1. Turn on the projector and display an image.
2. Press theFocusbutton on the remote control or press the Lensbutton on the control panel
repeatedly until the focus adjustment screen appears.   
						

							92
3. Press the left or right arrow buttons until the center of the image is focused.
4. Press the
Focusbutton on the remote control or press the Lensbutton on the control panel
repeatedly until the distortion adjustment screen appears.
5. Press the left or right arrow buttons until the edges of the image are also focused.   
						

							93
Note:
If you installed the optional ELPLU02 short throw lens and you see a message prompting you
to manually adjust the image distortion, manually rotate the distortion ring counterclockwise. Adjust
the focus and then rotate the distortion ring to correct image distortion.
Parent topic: Focusing the Image Using the Focus Button
Setting the Lens Type After installing one of the following lenses, you need to select the model number for the lens: ELPLS04,
ELPLU02, ELPLR04, ELPLW04, ELPLM06, ELPLM07, or ELPLL07.
1. Turn on the projector and display an image.
2. Press theMenubutton.
3. Select the Extendedmenu and press Enter.
4. Select Operation >Advanced >Lens Type.
5. Select your lens model number and press Enter.
6. Press the Menubutton to exit.
Parent topic: Using Basic Projector Features
Setting the Screen Type You can use the Screen Type setting to match the aspect ratio of the displayed image to the screen you
are using.
1. Turn on the projector and display an image.
2. Press theMenubutton.  
						

							94
3. Select the
Extendedmenu and press Enter.
4. Select Display>Screen >Screen Type.
You see this screen:
5. Select your screens aspect ratio and press Enter.
6. Press the Menubutton to exit.
7. Adjust the aspect ratio for the projected image, if necessary.
Parent topic: Using Basic Projector Features
Related concepts
Image Aspect Ratio
Adjusting the Image Position Using Lens Shift If you cannot install the projector directly in front of the screen, you can adjust the position of the
projected image using the lens shift feature.
Note:Wait 20 minutes after turning on the projector before setting the focus, zoom, and lens shift for
maximum accuracy. Lens shift is not supported for the ELPLR04 lens.
1. Turn on the projector and display an image. 
						

							95
2. Press the
Lens Shiftbutton on the remote control or the Lensbutton on the control panel.
3. Press the arrow buttons to adjust the position of the projected image as necessary. Pro L1100U/L1200U/L1300U/L1405U - ELPLU03, ELPLU04, ELPLW05, ELPLW06, ELPLM08,
ELPLM09, ELPLM10, ELPLM11, or ELPLL08 lens
1 Center of lens
2 Projected image when lens shift is set to the home position
3 Maximum range: V × 67%; maximum range when performing screen matching: V × 44% (ELPLU03), V ×51% (ELPLM09)
4 Maximum range when the lens is shifted horizontally all the way: V × 19%; maximum range when performing screen matching: V × 64% (ELPLU03)  
						

							96
Pro L1100U/L1200U/L1300U/L1405U - ELPLX01 lens
1 Center of lens
2 Projected image when lens shift is set to the home position
3 Maximum range: V × 17%
Note: You cannot move the image upward when the lens is shifted horizontally all the way.
Pro L1500U/L1505U - ELPLU03 or ELPLW05 lens
1 Center of lens
2 Projected image when lens shift is set to the home position
3 Maximum range: V × 24%; maximum range when performing screen matching: V × 11% (ELPLU03)   
						

							97
Note:
You cannot move the image upward when the lens is shifted horizontally all the way.
Pro L1500U/L1505U - ELPLU04, ELPLW06, ELPLM09, ELPLM10, ELPLM11, or ELPLL08 lens
1 Center of lens
2 Projected image when lens shift is set to the home position
3 Maximum range: V × 60%; maximum range when performing screen matching: V × 40% (ELPLU04)
4 Maximum range when the lens is shifted horizontally all the way: V × 31%
4. When you are finished, press the Escbutton on the control panel or remote control.
Note: When adjusting the image height, position the image lower than where you want it to be and then
move it up. This will help prevent the image from moving down after adjustment. The image is clearest
when the lens is at the home position. To move the lens to the home position, press and hold the Lens
Shift button on the remote control or the Lensbutton on the control panel for at least three seconds.
Parent topic: Using Basic Projector Features
Adjusting the Image Position Using Screen Position You can adjust the image position if there are margins between the edge of the image and the projected
screen frame.  
						

							98
Note:
You cannot adjust the screen position if the Screen Type is set to 16:10.
1. Turn on the projector and display an image.
2. Press the Menubutton.
3. Select the Extendedmenu and press Enter.
4. Select Display>Screen >Screen Position.
5. Use the arrow buttons on the remote control or projector to adjust the position of the image.
6. When you are finished, press the Menubutton.
Parent topic: Using Basic Projector Features
Related tasks
Setting the Screen Type
Displaying a Test Pattern You can display a test pattern to adjust the projected image without connecting a computer or video
device.
Note:The test patterns shape is determined by the Screen Type setting. Be sure to set the correct
screen type before adjusting with the test pattern.
1. Turn on the projector.
2. Press the Test Patternbutton on the remote control or the down arrow button on the control panel.  
						

							99
3. Press the left or right arrow buttons on the remote control or press
Enteron the control panel to
cycle through the available test patterns.
4. Adjust the image as necessary.
5. Press the Escto clear the test pattern.
Available Test Pattern Image Adjustments
Parent topic: Using Basic Projector Features
Related tasks
Setting the Screen Type
Available Test Pattern Image Adjustments You can adjust the following settings while the test pattern is displayed.
Menu Settings
Image Color Mode
White Balance
Advanced
•Gamma 1
• RGBCMY
Signal Auto Setup
Settings Geometry Correction
Brightness Settings
Extended Display2
Color Calibration
Multi-Projection 3
1 Except for custom Gammasettings
2 Except for the Screen,Panel Alignment, and Color Uniformitysettings
3 Except for the Black Level,Scale,Color Uniformity, and Color Adjustmentsettings
Parent topic: Displaying a Test Pattern 
						

							100
Adjusting the Image Height
If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust
the image height using the projectors adjustable feet.
1. Turn on the projector and display an image.
2. To adjust the image height, rotate the front foot to extend or retract it.
3. If the image is tilted, rotate the rear feet to adjust their height.
If the projected image is unevenly rectangular, you need to adjust the image shape.
Parent topic:Using Basic Projector Features