Epson Projector EX9200 Pro User Manual

							Caution:
Do not over-tighten the screws.
9. Replace the lamp cover and tighten the screw to secure it.
Note: Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp’s usage.
Parent topic: Projector Lamp Maintenance
Related tasks
Resetting the Lamp Timer
Resetting the Lamp Timer You must reset the lamp timer after replacing the projectors lamp to clear the lamp replacement
message and to keep track of lamp usage correctly.
Note:Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage
information.
1. Turn on the projector.
2. Press the Menubutton.
161  
						

							3. Select the
Resetmenu and press Enter.
4. Select Reset Lamp Hours and pressEnter.
You see a prompt asking if you want to reset the lamp hours.
5. Select Yesand press Enter.
6. Press MenuorEsc to exit the menus.
Parent topic: Projector Lamp Maintenance
Related tasks
Replacing the Lamp
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they
run out.
Caution:Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
162 
						

							1. Remove the battery cover as shown.
2. Remove the old batteries.
Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on
your hands. If it gets on your hands, wash them immediately to avoid injury.
3. Insert the batteries with the +and –ends facing as shown.
163   
						

							4. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Projector Maintenance
Related references
Remote Control Operation
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport,
ship, or store the projector safely:
• Close the lens cover to protect the lens.
• Remove any equipment connected to the projector.
• Use a carrying case to hand-carry the projector.
• When transporting the projector a long distance or as checked luggage, place it in a carrying case.Then pack the case in a firm box with cushioning around it and mark the box Fragile.
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box Fragile.
Note: Epson shall not be liable for any damages incurred during transportation.
Parent topic: Maintaining and Transporting the Projector
164  
						

							Solving Problems
Check the solutions in these sections if you have any problems using the projector.
Projection Problem Tips
Projector Light Status
Using the Projector Help Displays
Solving Image or Sound Problems
Solving Projector or Remote Control Operation Problems
Solving Network Problems
Where to Get Help
Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it
on.
If this does not solve the problem, check the following:
• The lights on the projector may indicate what the problem is.
• The Help option on the Home screen can display information about common problems, if the projectoris operating.
• The solutions in this manual can help you solve many problems.
If none of these solutions help, you can contact Epson for technical support.
Parent topic: Solving Problems
Related references
Projector Light Status
Where to Get Help
Related tasks
Using the Projector Help Displays
165 
						

							Projector Light Status
The lights on the projector indicate the projector status and let you know when a problem occurs. Check
the status and color of the lights and look for a solution in the table here.
1 Power light
2 Status light
3 Wireless LAN light (EX9200 Pro)
4 Lamp light
5 Temp (temperature) light
Power light Status light Lamp light Temp light Status and solution
Blue BlueOff OffNormal operation
Blue Flashing blue Off OffWarming up or cooling down
Blue OffOff OffStandby or sleep mode
166  
						

							Power light Status light Lamp light Temp light Status and solution
Flashing blue Light status Light status Flashing Projector is too hot.
varies varies orange • Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• Make sure the environmental temperature is not too hot.
Off Flashing blue Off Orange Projector has overheated and
turned off. Leave it turned off to
cool down. Once the Temp and
Status lights turn off and the power
light turns blue (after about five
minutes), try the suggestions
below:
• Make sure that the vents and airfilter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• If operating the projector at high altitude, turn on High Altitude
Mode.
• If the problem persists, unplug the projector and contact Epson
for help.
167 
						

							Power light Status light Lamp light Temp light Status and solution
Off
Flashing blue Orange Off Lamp has a problem.
• Check to see if the lamp is
burned out, broken, or installed
incorrectly. Reseat or replace the
lamp as necessary.
• Clean or replace the air filter.
• If operating the projector at high altitude, turn on High Altitude
Mode.
• If the problem persists, unplug the projector and contact Epson
for help.
Flashing blue Light status Flashing Light status Replace the lamp soon to avoid varies orange varies damage. Do not continue using the projector.
Off Flashing blue Off Flashing A fan or sensor has a problem.
orange Turn the projector off, unplug it, and
contact Epson for help.
Off Flashing blue Flashing Off Internal projector error. Turn the
orange projector off, unplug it, and contact
Epson for help.
Off Flashing blue Flashing Flashing Auto iris error. Turn the projector
orange orange off, unplug it, and contact Epson for help.
Off Flashing blue Orange Orange Power error. Turn the projector off,
unplug it, and contact Epson for
help.
Light status Light status Flashing Flashing When transferring settings between
varies varies orange rapidly orange rapidly projectors, the settings file may be corrupt or the USB flash drive or
USB cable may not be properly
connected. Remove the flash drive
or cable, unplug the power cord,
and try again.
168 
						

							Power light Status light Lamp light Temp light Status and solution
Flashing blue Flashing blue Flashing Flashing When transferring settings between
rapidly rapidly orange rapidly orange rapidly projectors, writing may have failed
and a projector error may have
occurred. Turn the projector off,
unplug it, and contact Epson for
help.
Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and
contact Epson for help.
Parent topic: Solving Problems
Related references
Projector Setup Settings - Extended Menu
Where to Get Help
Projector Environmental Specifications
Related tasks
Cleaning the Air Filter and Vents
Replacing the Air Filter
Replacing the Lamp
Using the Projector Help Displays You can display information to help you solve common problems using the projectors Help system.
1. Turn on the projector.
2. Press theHomebutton on the projector or the remote control.
3. Use the arrow buttons to select Help.
4. Press Enter.
You see the Help menu.
5. Use the up and down arrow buttons to highlight the problem you want to solve.
6. Press Enterto view the solutions.
7. When you are finished, do one of the following: • To select another problem to solve, press Esc.
169 
						

							• To exit the help system, press
Home.
Parent topic: Solving Problems
Solving Image or Sound Problems Check the solutions in these sections if you have any problems with projected images or sound.
Solutions When No Image Appears
Solutions When Image is Incorrect Using the USB Display Function
Solutions When No Signal Message Appears
Solutions When Not Supported Message Appears
Solutions When Only a Partial Image Appears
Solutions When the Image is Not Rectangular
Solutions When the Image Contains Noise or Static
Solutions When the Image is Fuzzy or Blurry
Solutions When the Image Brightness or Colors are Incorrect
Solutions to Sound Problems
Parent topic:Solving Problems
Solutions When No Image Appears If no image appears, try the following solutions:
• Make sure the lens cover is open all the way or off.
• Press theA/V Mutebutton on the remote control to see if the image was temporarily turned off.
• Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
• Press the projectors power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver.
• Press the Menubutton. If the projector menu is able to display, there may be a problem with the
connected video source, cable connection, or port.
• Check the settings on the Signal menu to make sure they are correct for the current video source.
• Adjust the Brightnesssetting or select the NormalPower Consumption setting.
• Check the Displaysetting to make sure Messagesis set toOn.
• If the projector does not respond when you press the control panel buttons, the buttons may be locked. Unlock the buttons.
170