Epson Projector Ex90 User Manual

Welcome11
Save all packaging in case you need to ship the projector. Always use 
the original packaging (or equivalent) when you need to send the 
projector to another location.
Projector Parts
Front
Control panel
Air exhaust 
vent
Front adjustable foot
Foot release leverRemote control 
sensor
Monitor Out port Computer (Component Video) port
S-Video port
Video 
port USB port
Remote 
control sensor
SpeakerAudio 
input ports
Rear adjustable foot Power inlet
A/V mute slide 
Back
Kensington lock port 
(on...

12Welcome
Bottom
Control Panel
Air filter
Security lock slot
Hole for 
attaching 
ceiling mount 
bracket Holes for 
attaching 
ceiling mount 
bracket
Up and Down buttons 
correct keystone distortion 
and select menu itemsUp 
button
Down 
button Enter button automatically 
adjusts computer image
  and  buttons adjust 
volume and 
select menu 
items 
Lights indicate 
projector status 

Welcome13
Additional Components
Depending on how you plan to use the projector, you may need 
additional components:
■To receive an S-Video signal, you need an S-Video cable. One is 
usually provided with your video device, or you can purchase it 
from Epson. See page 14.
■To receive a component video signal from a VCR or other video 
device, you’ll need a component video cable and the VGA 
component adapter included with your projector.
■Some older PowerBooks and Macintosh desktop models may 
need a...

14Welcome
Optional Accessories
To enhance your use of the projector, Epson provides the following 
optional accessories:  
You can purchase screens, carrying cases, or other accessories from an 
Epson authorized reseller. To find the nearest reseller, call 
800-GO-EPSON (800-463-7766). Or you can purchase online at 
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Product Product number
Replacement lamp V13H010L42
Air filter set (includes 2 filters) V13H134A13
Soft shoulder case
Wheeled...

15
1
Setting Up the Projector
This chapter tells you how to set up the projector and connect it to a 
computer or video source. You can connect up to three devices 
simultaneously: three video sources, or one computer and two video 
sources. 
You’ll find instructions for the following in this chapter:
■Positioning the projector
■Connecting to a computer
■Connecting to video sources 

16Setting Up the Projector
Positioning the Projector
Before connecting the projector, you 
need to decide where to place it. If 
you’re setting up the projector yourself 
and it isn’t already installed in the 
room you’re using, you’ll probably 
want to place it on a table in front of 
the screen, as shown.
This lets you stand in the front of the room, face the audience, and 
remain close enough to the equipment to be able to control it. Try to 
leave as much space as possible between the projector and...

Setting Up the Projector17
Try to place the projector directly in front of the center of the screen, 
facing it toward the screen squarely. If the projector isn’t positioned 
this way, the image will be “keystone” shaped, instead of square or 
rectangular.
If you place the projector below the level of the screen, you’ll have to 
tilt it up by extending the front adjustable foot, as described on 
page 38. This also causes the image to lose its rectangular shape. You 
can adjust the shape using the buttons...

18Setting Up the Projector
Connecting to a Computer
You can connect the EX90 projector to any computer that has a 
standard VGA or BNC monitor port, including PC notebook and 
laptop computers, Macintosh PowerBooks and iBooks, and hand-held 
devices. 
Follow the instructions in this section to:
■Connect the projector to your computer with the VGA cable 
included with the projector.
■Connect the projector to your computer with a commercially 
available VGA–5BNC cable.
After connecting the projector to...

Setting Up the Projector19
Connecting with the VGA Cable
Follow these instructions to connect to your computer with the VGA 
cable that came with your projector. Before you start, make sure your 
computer and the projector are turned off.
1. If you are connecting the projector to a desktop computer, 
disconnect the monitor cable from your computer.
2. Locate the VGA computer cable that 
came with the projector.
Connect one end of the cable to the 
projector’s 
Computer (Component 
Video) 
port.
3....

20Setting Up the Projector
Connecting with a VGA-5BNC Cable
If your computer provides video output through BNC connectors, 
follow these instructions to connect the projector to your computer 
with an optional VGA-5BNC cable. Before you start, make sure your 
computer and the projector are turned off.
1. Disconnect the monitor cable from your computer.
2. Connect the cable’s VGA connector to the projector’s 
Computer 
(Component Video) 
port.
3. Connect the BNC connectors to your computer’s BNC ports.
4....