Epson Projector Ex7200 User Manual

Fine-Tuning the Projector81
Choosing When to Display the Image
After your image is saved, you can set it to display as the startup 
screen, the screen you see when there’s no signal, or the screen you see 
when you press the 
A/V Mute button (see page 58).
1. Press the 
Menu button, highlight the Extended menu, and press 
Enter. 
2. Select 
Display and press Enter.
3. Choose from these display options:
■Set Display Background to Logo to display your image 
when there is no signal. 
■Set Startup Screen to...

82Fine-Tuning the Projector5. Press the 
Menu button to exit. 
To disable the Control Panel Lock function, select 
Off in the Control 
Panel Lock menu. Or press and hold the 
Enter button on the 
projector’s control panel for seven seconds. A message is displayed and 
the lock is released.
Using Security Locking
The projector includes two security locking points to prevent its theft 
when installed or used in public locations: 
■Security cable attachment. You can attach a commercially 
available security...

83
5
Maintaining the Projector
Your projector needs little maintenance. All you have to do on a 
regular basis is clean the lens, and check that the air filter and vents are 
clean. A clogged air filter or vent can block ventilation needed to cool 
the projector.
The only parts you should replace are the lamp and air filter. If any 
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■Cleaning the lens
■Cleaning the projector case
■Cleaning the air...

84Maintaining the Projector
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
To remove dirt or smears on the lens, use a commercially available 
cloth for cleaning glasses.
Cleaning the Projector Case
Before cleaning, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free 
cloth.
■To remove stubborn dirt or stains, moisten a soft cloth with water 
and a neutral detergent and firmly wring the cloth dry. Then...

Maintaining the Projector85
You can remove the air filter to clean both sides.
If the filter is too dirty or broken, replace the filter as described below. 
Replacing the Air Filter
You need to replace the air filter if:
■You cannot remove the dust from it
■The air filter is damaged or torn
■You repeatedly see a projected message telling you to clean or 
replace it
1. Turn off the projector and unplug the power cord.
2. Open the air filter cover on the side of the projector.
3. Lift the air filter out of...

86Maintaining the Projector4. Slide the new air filter into the slot until it clicks into place.
5. Close the air filter cover.
Replacing the Lamp
The life span of the projection lamp is about 4,000 hours if Power 
Consumption 
in the Settings menu is Normal (default), and 5,000 
hours if this setting is 
ECO. See page 90 to check the lamp usage.
It is time to replace the lamp when: 
■The projected image gets darker or starts to deteriorate.
■The message Replace the lamp appears on the screen and the...

Maintaining the Projector87
You may also need to replace the lamp if the Lamp light flashes 
red. See page 95.
Contact your dealer or call Epson at 800-GO-EPSON 
(800-463-7766). Request part number V13H010L58.
Follow these steps to replace the lamp:
1. Turn off the projector and unplug the power cord.
2. Let the projector cool for at least an hour (if it has been on). The 
lamp is extremely hot immediately after use. 
3. Loosen the lamp cover screw (you cannot remove it). Then slide 
the lamp cover off....

88Maintaining the Projector4. Loosen the two screws holding the lamp in place (you can’t 
remove them).
5. Hold the lamp as shown and pull it straight out.
 
6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is 
facing the right way.) Then tighten its screws.
Loosen, but don’t 
remove these screws
note
The lamp(s) in this 
product contain mercury. 
Please consult your state and 
local regulations regarding 
disposal or recycling. Do not 
put in the trash. 

Maintaining the Projector89
7. Replace the lamp cover, then tighten its screw.
8. Reset the lamp timer as described in the next section. 
Resetting the Lamp Timer
After you replace the lamp, you need to reset the lamp timer using the 
projector’s menu system. 
1. Press the 
Menu button on the remote control or on the 
projector’s control panel. You see the main menu.
2. Select the 
Reset menu and press Enter. You see this screen:
3. Select 
Reset Lamp Hours and press Enter. 
4. When you see the prompt,...

90Maintaining the Projector
Checking Lamp Usage 
To check the number of hours the lamp has been used, press the 
Menu button and highlight the Info menu. You see a screen like this:
The life span of the lamp is about 4,000 hours if 
Power 
Consumption
 in the Settings menu is Normal (default), and 5,000 
hours if this setting is 
ECO. Make sure you have a spare lamp handy if 
the usage hours on this menu are close to the life span of your lamp.
Replacing the Remote Control Batteries
Replace the batteries...