Epson Projector Emp S1h User Manual

40
Advanced Operation > Configuration MenusfInfo menu
Computer images
Video images
Sub menu
Function
Lamp Hours Displays the cumulative lamp operating time. From 0 to 10 hours, 0H is displayed. After 10 hours, the usage 
time is displayed in hourly increments.
 When the accumulated usage time of the lamp reaches about 1900hours, a warning will be displayed in red.
Source Displays the input source being projected.
Input Signal
(Computer images only)Displays the input signal settings. 
Video Signal
(Video...

41
Advanced Operation > Configuration Menus
Sync Info 
(Computer images only)Displays picture signal information.
In the event that you are having problems with your projector and need to contact an EPSON Service Centre, 
please quote the information displayed on this screen.
Sub menu
Function 

42
Advanced Operation > Configuration MenusfReset menu
Sub menu
Function
Lamp-Hours Reset Resets the lamp operating time. When this command is selected, the cumulative lamp operating time is reset to the default 
value.
All Reset Resets all items in the configuration menus to their default settings.
 Press the [e] button and select Yes on the confirmation screen which is displayed.
 Select Reset in an individual menu to reset only the settings for the items in that sub menu.
 Input Signal, Language...

43
Troubleshooting
When You Suspect a ProblemFirst, check the indicators on the projector.
There are two indicators on the projector unit which notify you of projector conditions.Power indicator
lit   flashing•If the indicator is not lit, the power supply is not on.Condition
Cause/Remedy
s
Orange Standby state
(Not abnormal)
The power cable should only be disconnected when the projector is in this state.
Press the [Power] button to start projection.P.20
Orange Cool-down in progress 
(Not abnormal)
...

44
Troubleshooting > When You Suspect a ProblemWarning indicator
lit   flashing•Not lit under normal operating conditions.Condition
Cause/Remedy
s
Red High internal temperature (overheating)
The lamp turns off automatically and projection stops. Wait for about 5 minutes without operating the projector. 
After about 5 minutes have passed, unplug the power cable and check the following:
 Make sure the air filter and ventilation outlet are clear and that the projector is not positioned against a wall.
 If...

45
Troubleshooting > When You Suspect a Problem
p
 If problems with projection do occur, but the indicators do not show any abnormal conditions, please refer to the section When 
the indicators provide no help on the next page.
 If a condition occurs which is not listed in this table, please consult your dealer or contact the nearest address provided in the 
International Warranty Conditions in the Safety Instructions/World-Wide Warranty Terms guide.
 If you follow the above steps and are still unable...

46
Troubleshooting > When You Suspect a ProblemWhen the indicators provide no help• No images appear (Nothing is displayed) s P. 4 6
 No images appear (Messages are displayed 1) s P. 4 7
 No images appear (Messages are displayed 2) s P. 4 7
 Image is out of focus (unclear) s P. 4 8
 Vertical stripes appear in the image s P. 4 9
 Image is distorted / Image contains interference s P. 4 9 Only part of the image is displayed (large/small) s P. 5 0
 Image colours are poor, tinted green or tinted...

47
Troubleshooting > When You Suspect a ProblemfNo images appear (Messages are displayed 1)fNo images appear (Messages are displayed 2)
Not supported
 Check the mode which corresponds to the 
frequency of the image signals being output 
from the computer.
Refer to the documentation provided with your computer for details on 
changing the resolution and frequency of the image signals being output 
from the computer. sSupported Display Resolutions P.67
No signal
 Has external video output been selected...

48
Troubleshooting > When You Suspect a ProblemfImage is out of focus (unclear)
 The image is 
fuzzy
 Part of the 
image is out of 
focus
 The whole 
image is out of 
focus
 Have the Sync.
g, Tracking
g and 
Position settings been adjusted correctly?
If the configuration menu Image → Auto Setup setting has been set to 
OFF, press the [Auto] button on the remote control to adjust these 
settings. If the images have not been correctly adjusted after pressing the 
[Auto] button and using the auto setup...

49
Troubleshooting > When You Suspect a ProblemfVertical stripes appear in the imagefImage is distorted / Image contains interference
 Has the Tracking
g setting been adjusted?
Set the tracking value until the vertical stripes disappear. ([Menu] button 
Image → Picture Quality → Tracking) sImage menu P.35
 Have the Sync.
g, Tracking
g and 
Position settings been adjusted correctly?
If the configuration menu Image → Auto Setup setting has been set to 
OFF, press the [Auto] button on the remote control...