Epson Projector Emp 8000 User Manual

 
         
10 
2. To use the remote control as a wireless mouse, connect 
the 9-pin end of the PS/2 mouse cable or USB mouse 
cable included with the projector to the MOUSE terminal 
on the square end of the main cable.
3. Disconnect your mouse from the mouse port on the back 
of your computer and replace it with the other end of the 
PS/2 mouse cable or USB mouse cable included with the 
projector. (Your computer’s mouse will be disabled while 
you are using the remote control as a mouse.) 
♦...

 
Connecting to a Computer 
          

 
11 
Connecting the Audio Cable 
1. If you will be using audio, connect one end of the audio 
cable to the Audio 1 jack on the projector. (Use the Audio 
2 jack if you are connecting a second computer.)   
2. Connect the other end of the audio cable to the speaker or 
audio out port on the computer’s sound card.  
Connecting to a PC Laptop Computer  
To connect the projector to your PC laptop computer, you 
need to:
•Connect the computer cable
•Connect the...

 
         
12 
Connecting the Video Cable 
First connect the projector’s video cable to your laptop.  
♦ 
Note: 
 If your computer output is a 5BNC type, use the computer 
cable (5BNC). 
1. Connect one end of the computer cable to the projector’s 
Computer 1 port. (Use the Computer 2 port if you are 
connecting a second computer.)
2. Connect the other end of the video cable to the laptop’s 
video (monitor) port.
3. Tighten the screws on all connectors. 
Connecting the Mouse and Serial Cables 
If you...

 
Connecting to a Computer 
          

 
13
Refer to this illustration while following the steps below.
1. Connect the small end of the main cable to the projector’s 
Mouse/Com 1 port. (Use the Mouse/Com 2 port if you 
are connecting a second computer.)
2. To use the remote control as a wireless mouse, connect 
the 9-pin end of the PS/2 mouse cable or USB mouse 
cable included with the projector to the MOUSE terminal 
on the square end of the main cable. 
3. Connect the 6-pin (mini-DIN) end of the...

        
14
♦Note: If your laptop uses a serial mouse, perform steps 2 and 3 
using the PC serial mouse cable instead of the PS/2 mouse cable  
or USB mouse cable (not shown in the illustration). 
4. To use the ELP Link IV software or to use the Effects 
buttons on the remote control, connect one end of the 
serial cable to the SERIAL terminal on the square end of 
the main cable. 
5. Connect the other end of the serial cable to the serial port 
on the back of your computer.
♦Note: You will not be...

Connecting to a Computer
          
15
Connecting the Audio Cable
1. If you will be using audio, connect one end of the audio 
cable to the Audio 1 jack on the projector. (Use the Audio 
2 jack if you are connecting a second computer.)   
2. Connect the other end of the audio cable to your laptop. 
Connecting to a Desktop Macintosh 
To connect the projector to your desktop Macintosh, you 
need to:
•Connect the computer cable and computer monitor cable
•Connect the mouse and/or serial cable (if you...

        
16
Connecting the Video and Monitor Cables
First connect the video and monitor cables. Refer to this 
illustration as you follow the steps below. 
1. Connect one end of the computer cable to the projector’s 
Computer 1 port. (Use the Computer 2 port if you are 
connecting a second computer.)
♦Note: If your computer output is a 5BNC type, use the computer 
cable (5BNC).
Macintosh 
desktop adapter
Macintosh 
monitor adapter
Macintosh 
monitor cable
computer 
cable Computer Out port
Computer 1...

Connecting to a Computer
          
17
2. Remove the small cover on the Macintosh desktop adapter 
(as shown below) and set its DIP switches in accordance 
with the resolution you want to use, such as 16-inch 
mode. See your Macintosh documentation for 
instructions.
3. Connect the small terminal of the Macintosh desktop 
adapter to the other end of the computer cable.
4. Disconnect the monitor cable from the video port on the 
back of the Macintosh. Then connect the computer cable 
(with the...

        
18
5. To also view the video on the computer’s monitor, attach 
the large end of the Macintosh monitor adapter to the 
monitor cable and connect the other end of the adapter to 
the projector’s Computer Out port.
6. Tighten the screws on all the connectors.
Connecting the Mouse and Serial Cables
If you want to use the remote control as a mouse or use the 
ELP Link IV software, you need to connect the main cable. It 
provides connectors for:
•The Mac mouse cable or USB mouse cable (to use the...

Connecting to a Computer
          
19
Refer to this illustration while following the steps below.   
1. Connect the small end of the main cable to the projector’s 
Mouse/Com 1 port. (Use the Mouse/Com 2 port to 
connect a second computer.)
Mouse/Com 1 port
Mac mouse cable
(or USB mouse cable)Mac serial cable
main cable