Epson Projector Emp 710 User Manual

 
Connecting to a Computer 
n  n  n  n  n  
n
 
13  Connecting to a Desktop Macintosh   To connect the projector to your desktop Macintosh, you 
need to:
• Connect the computer cable
• Connect the mouse cable (if you want to use the remote 
control as a mouse)
• Connect the audio cable (if you’ll be projecting with audio)
Follow the steps in each section for the cables you need to 
connect. Before beginning, turn off the projector and 
computer if they are on.
  ¨  Note:   Macintosh configurations vary....

 
  n  n  n  n 
14  1. Connect one end of the computer cable to the projector’s 
Computer port.
2. Remove the small cover on the Macintosh desktop adapter 
and set its DIP switches in accordance with the resolution 
you want to use (such as 16-inch mode). See your 
Macintosh documentation for instructions. 

 
Connecting to a Computer 
n  n  n  n  n  
n
 
15  3. Connect the small terminal of the Macintosh desktop 
adapter to the other end of the computer cable.
4. Connect the computer cable (with the Macintosh desktop 
adapter attached) to the video-out port on your 
Macintosh.  Connecting the Mouse Cables  If you want to use the remote control as a mouse, you need to 
connect the Mac mouse cable or USB mouse cable.
Refer to this illustration while following the steps below.    
Mouse/Com portUSB mouse...

 
  n  n  n  n 
16  1. Connect one end of the projector’s Mac mouse cable or 
USB mouse cable to the Mouse/Com or USB Mouse port 
on the projector
2. Disconnect your Macintosh’s mouse cable. Connect the 
other end of the projector’s Mac mouse cable or USB 
mouse cable to the mouse port on your Macintosh.  Connecting the Audio Cable  1. If you will be using audio, connect one end of the audio 
cable to the Audio In jack on the projector.   
2. Connect the other end of the audio cable to the Audio 
Out...

 
Connecting to a Computer 
n  n  n  n  n  
n
 
17  Connecting to a PowerBook   Your PowerBook must have video-out capability in order to 
connect to the projector. 
To connect the projector to your PowerBook, you need to:
• Connect the computer cable
• Connect the mouse cable (if you want to use the remote 
control as a mouse)
• Connect the audio cable (if you’ll be projecting with audio)
Follow the steps in each section for the cables you need to 
connect. Before beginning, turn off the projector and...

 
  n  n  n  n 
18  ¨  Note:   Some new PowerBooks may allow you to connect the 
computer cable directly to the computer without using a 
video-out cable. See your PowerBook manual for additional 
information on connecting a computer cable.
  1. Connect one end of the computer cable to the projector’s 
Computer port.
2. Remove the small cover on the Macintosh desktop adapter 
and set its DIP switches in accordance with the resolution 
you want to use (such as 16-inch mode). See your 
Macintosh...

 
Connecting to a Computer 
n  n  n  n  n  
n
 
19  3. Connect the small terminal of the Macintosh desktop 
adapter to the other end of the computer cable.
4. Connect the computer cable (with the Macintosh desktop 
adapter attached) to the video-out port on the 
PowerBook. 
If a video-out cable was provided with your PowerBook, 
connect the smaller end of the video-out cable to the video-
out port on the back of the PowerBook. Connect the other 
end to the Macintosh desktop adapter on the end of the...

 
  n  n  n  n 
20  Connecting the Mouse Cables  If you want to use the remote control as a mouse, you need to 
connect the Mac mouse cable or USB mouse cable.
Refer to this illustration while following the steps below. 
1. Connect one end of the projector’s Mac mouse cable or 
USB mouse cable to the Mouse/Com or USB Mouse port 
on the projector.
Mac mouse cable Mouse/Com port
USB mouse cable 

 
Connecting to a Computer 
n  n  n  n  n  
n
 
21  2. Connect the other end of the Mac mouse cable or USB 
mouse cable to the mouse port on the back of the 
PowerBook.  Connecting the Audio Cable  1. If you will be using audio, connect one end of the audio 
cable to the Audio In jack on the projector. 
2. Connect the other end of the audio cable to the audio-out 
port on your PowerBook. 
¨
Note: After you turn on the projector and computer, you’ll need 
to choose Mirroring in the Display Control Panel...

 
  n  n  n  n 
22  Connecting to a Video Source  You can connect a VCR, a camcorder, a laser disc player, 
DVD player, or any other compatible video image source to 
your projector.
The projector can receive composite video or S-Video. Your 
equipment has composite video if your video source has a 
one-pin RCA video jack. Your equipment has S-Video if your 
video source has a four-pin (mini-DIN) video jack. 
¨ 
Note: 
 The projector is not compatible with a cable TV-style F 
connector. 
You can connect...