Epson Projector Emp 700 User Manual

 
Connecting to a Video Source 
n  n  n  n  n  
n
 
23  2. If your video source uses a small, round, one-prong 
composite (RCA) video connector, you’ll need the RCA 
video cable that comes with the projector. If your video 
source uses a large, round, four-prong S-Video connector, 
you will need to purchase the appropriate cable or use the 
cable that came with your video source.
3. For Composite Video, connect the yellow RCA plug on 
one end of the RCA video cable to the projector’s Video 
jack. Connect...

 
  n  n  n  n 
24  6. Connect the RCA audio cable to the Audio jacks of the 
projector: insert the white plug into the L jack and the red 
plug into the R jack. Connect the plug at the other end of 
the RCA audio cable to the audio output jack of the video 
source. 
S-Video connector
S-Video cable 

 
Connecting to an External Speaker or PA System 
n  n  n  n  n  
n
 
25  Connecting to an External Speaker or 
PA System   
  Although the projector’s internal speakers are enough for 
most small- or medium-size rooms, you can connect the 
projector to an external speaker or public address (PA) system 
for large rooms or to gain maximum benefit.
To connect the projector to an external sound system, you 
need to obtain an RCA-to-3.5 mm stereo audio cable. You 
can get one from your computer dealer.
1....

 
  n  n  n  n 
26 

   
    
n
     
      n              n       
n     n    n     n     n    n    n     n     n      n      n      n
n  n  n  n  n  n
27
2
Using the Projector
This chapter provides the following information about using 
your projector:
• Turning the equipment on and off
• Focusing and positioning the screen image
• Controlling the projector with the remote control and the 
operation panel
• Monitoring the projector’s operating status 

  n  n  n  n
28
The illustration below identifies the parts of your projector.
operation panel
operation indicator
zoom ring
focus ring
front foot
foot adjust lever speaker
remote 
control 
receiver 

Turning the Equipment On and Off
n  n  n  n  n  n
29
Turning the Equipment On and Off
Turn on the projector and its attached equipment in the 
following order.
1. Video source
2. Audio source (if different from computer or video source)
3. Projector
4. External speaker or PA system (if necessary)
5. Computer
When you turn off the equipment, do so in the reverse order.
Turning the Projector On and Off
1. Remove the projector lens cap.
2. When you plug in the projector power cord, the power 
indicator...

  n  n  n  n
30
After you press the power button to turn off the projector, a
confirmation message appears. If you want to turn off the 
projector, press the power button again. If you don’t want to 
turn off the projector, press any button. The fan will remain 
on and the operation indicator will flash orange for about one 
minute as the projector cools down.
When the projector has cooled down, the operation indicator 
stops flashing and remains orange.
¨
Note: If you press the Power button to turn the...

Focusing and Positioning the Screen Image
n  n  n  n  n  n
31
Focusing and Positioning the Screen 
Image
When an image appears on the screen, check that it is in focus 
and correctly positioned on the screen.
• To focus the image, rotate the focus ring (the outer ring on 
the lens). 
• To adjust the size of the image, rotate the inner zoom ring. 
Rotate the zoom ring between W (wide) and T (tele) 
marks.
zoom ringfocus ring 

  n  n  n  n
32
If you need to raise or lower the image on the screen, extend 
or retract the two feet at the bottom of the projector as 
follows:
1. Stand behind the projector and support the front of it 
while you lift the foot adjust levers above the feet. This 
unlocks the feet so they can move up and down freely. Do 
not let the projector drop.
¨
Caution: Do not hold the projector by its lens. This can damage 
the lens.
2. While lifting the foot adjust levers, raise or lower the 
projector until the...