Epson Projector Emp 61 User Manual

							60
Using the Configuration Menu Functions
Reset
Resets all adjustment values for the Setting menu functions 
to their default settings.
Press the [Enter] button on the remote control or on the 
projectors control panel.
To return all settings such as the Image and Signal 
menu settings to their default values, selectReset All from 
the Reset menu.
 sp.65
-
Sub-menu
Function
Default 
						

							61
Using the Configuration Menu Functions
The User’s Logo setting can not be adjusted if no 
signals are being input.
Extended Menu
Sub-menu
Function
Default
Display
This lets you make settings related to the projectors display.
Message:
Sets whether display of the following messages is turned 
ON or OFF.
 Signal name when the video signal is switched
 Colour mode name when the colour mode is switched
 When no image signals are being input
 When an incompatible signal is input
 When the air filter needs replacing
Background Color:
Sets the screen status when the [A/V Mute] button on the 
remote control is being pressed or when no image signals 
are being input to Black, Blue or Logo.
 To change the users logo, you need to record your own 
logo. sp.90
 If the User’s Logo Protect function of Password Protect 
has been set to ON, the Logo setting cannot be 
changed from Logo to Black or Blue, or from 
Black or Blue to Logo. Cancel the Password 
Protect function before changing these settings. sp.29
Startup Screen:
Sets whether the startup screen is displayed or not.
To change the users logo, you need to record your own 
users logo. sp.90
This cannot be changed from enabled (ON) to disabled 
(OFF) if the User’s Logo Protect function of Password 
Protect has been set to ON. Cancel the Password Protect 
function before changing the setting. sp.29
Message: ON
Background 
Color: 
Blue
Startup Screen: 
ON
User’s 
Logo
Records a users logo. sp.90
Press the [Enter] button on the remote control or on the 
projectors control panel and then follow the instructions 
that appear on the screen.
A users logo cannot be recorded if the User’s Logo 
Protect function of Password Protect has been set to ON. 
Cancel the Password Protect function before recording a 
users logo. sp.29
EPSON logo 
						

							62
Using the Configuration Menu Functions
Projection
Sets the projection position for the projector.
 Front : Select when the projector is in front of the 
screen.
 Front/Ceiling : Select when the projector is in front of the 
screen and suspended from the ceiling.
 Rear : Select when the projector is behind the 
screen.
 Rear/Ceiling : Select when the projector is behind the 
screen and suspended from the ceiling.
Front
Operation
This lets you make settings related to projector operation.
Direct Power ON: 
When the projectors power cable is connected, projection 
starts without needing to press the [Power] button.
* When Direct Power ON is set to ON, turn the power 
off by pressing the [Power] button, then wait for the cool-
down
g period to finish and then disconnect the power 
cable. If the power cable is left connected to the wall 
outlet when Direct Power ON is set to ON, the 
projector will turn on if a power outage occurs and then 
the power is restored.
Sleep Mode: 
Sets the energy saving operation when no signal is being 
input.
 When set to ON, projection stops automatically and 
then after the cool-down
g period is finished, the 
projector changes to sleep mode if no operations are 
carried out for 30 minutes while the No Signal. 
message is being displayed. (The Power indicator lights 
orange.)
 Projection starts again when the [Power] button is 
pressed.
Direct Power 
ON: OFF
Sleep Mode: 
OFF
Sub-menu
Function
Default 
						

							63
Using the Configuration Menu Functions
* EMP Monitor : Allows you to monitor multiple projectors on 
the network and control them all at once using functions 
such as turning the power on and off and switching input 
sources.
To use the EMP Monitor, an adapter and cable for conversion  
are required. The followings are available products. 
(As of May, 2004)
For details on the products, visit LANTRONIXs website.
Adapters:
UDS100, UDS200 (LANTRONIX) 
Cables:
For the UDS100
RS-232C cable (straight, mini D-Sub9pin female/mini 
D-Sub25pin male)
For the UDS200
RS-232C cable (cross, mini D-Sub9pin female/mini 
D-Sub9pin female)
For the detailed and current information about the software, 
please visit the following website.
http://www.epson.co.uk/support/download/
Sub-menu
Function
Default
Standby 
Mode
Set to Network ON to use network monitoring and control 
functions and the standby monitor out function while the 
projector is in standby mode.
If you change the setting, the new setting will be enabled 
after the power is turned off.
We provide softwares* for network monitoring and 
controlling projectors.
When set to Network ON, the Power indicator will flash 
orange and then remain orange after disconnecting the 
power plug and reinserting it into the electrical outlet.
Network OFF
COM Port
This can be set to either RS-232C or USB, depending on 
the port that is being used for communication with a 
computer.
If you change the setting, the new setting will be enabled 
after the power is turned off.
RS-232C
Language
Sets the language for message displays.
Press the [Enter] button on the remote control or on the 
projectors control panel and then make the selection.
English
(Varies 
depending on 
country of 
purchase)
Reset
Returns Display and Operation settings in the 
Extended menu to their default settings.
However, if Background Color has been set to Logo or if 
Startup Screen has been set to OFF, the settings will not 
be returned to their defaults if User’s Logo Protect is set to 
ON. sp.29
Press the [Enter] button on the remote control or on the 
projectors control panel.
To return all settings such as the Image and Signal 
menu settings to their default values, select Reset All 
from the Reset menu.
 sp.65
- 
						

							64
Using the Configuration Menu Functions
The Info menu shows the setting details for the current 
image source.
The Lamp Hours item appears as 0H for 0–10 hours, 
and after that, it appears in units of 1 hour.
Computer/RGB Video/Component video
g
Composite video
g/ S-Video
g
Info Menu
Sub-menu
Function
Default
Lamp 
Hours
Displays the cumulative lamp operating time for both 
High Brightness and Low Brightness.
When the lamp warning period is reached, the display 
characters appear in red.
0H
Source
Displays the input source which is currently being projected.
Input 
Signal
Displays the input signal settings. 
(Does not appear when the input source is composite video 
or S-video.)
Resolution
Displays the input resolution. 
(Does not appear when the input source is composite video 
or S-video.)
-
Video 
Signal
Shows the video signal format.
(Not displayed for computer, RGB video or component 
video images)
-
Refresh Rate
g
Displays the refresh rate. 
(Does not appear when the input source is composite video 
or S-video.)
-
Sync.
g 
Info
Informations in this menu may be required in case that you 
ask for service to your dealer or the nearest address provided 
at International Warranty Conditions section of the Safety 
Instructions/World Wide Warranty Terms booklet.
(Does not appear when the input source is composite video 
or S-video.)
- 
						

							65
Using the Configuration Menu Functions
Reset Menu
Sub-menu
Function
Default
Reset All
Resets all items in all menus to their default settings.
Press the [Enter] button on the remote control or on the 
projectors control panel.
To reset settings such as Image or Signal, select Reset 
from the respective sub menus.
The Computer1 Input, Computer2 Input, Video 
Signal, User’s Logo, Lamp Hours and Language 
settings will not be reset to their defaults. However, if 
Background Color is set to Logo or Startup Screen is 
set to OFF, these settings will not be returned to their 
defaults when User’s Logo Protect is set to ON. 
sp.29
-
Lamp-
Hours 
Reset
Initialises the lamp operating time. When this command is 
selected, the cumulative lamp operating time is reset to the 
initial default value.
- 
						

							66
Using the Configuration Menu FunctionsUsing the Configuration Menus
The configuration menus can be operated using either the remote control or 
the projectors control panel.PROCEDURE
Press the [Menu] button.
The configuration menu appears.Select a menu item.
Tilt the [ ] button on the remote control up and down or press 
the [ ] and [ ] buttons on the projectors control panel to 
move to the item to be set.
Confirm the selection.
Press the [Enter] button to confirm the selection of a menu item.
1
Projector Remote control
2
3 
						

							67
Using the Configuration Menu Functions
Select a sub-menu item.
Tilt the [ ] button on the remote control up and down or press 
the [ ] and [ ] buttons on the projectors control panel to 
move to the sub-item to be set, and then press the [Enter] 
button.
The items that are displayed in the Image menu, Signal 
menu and Info menu vary depending on the input source that 
is being projected.
Change the setting.
Tilt the [ ] button on the remote control or press the [ ], 
[ ], [ ] and [ ] buttons on the projectors control panel to 
change the setting.
 : Current setting value
 : Currently-selected setting item
If you press the [Enter] button when at items with a   
displayed, the setting screen for that item will be displayed.
After making the setting, press the [Enter] button to accept the 
setting. The   will change to green.Close the menu.
Press the [Menu] button.
4
56
TIP
Refer to List of Functions for details on the functions of each menu 
item. sp.51 
						

							TroubleshootingThis chapter describes how to identify problems and what to do if a problem is found.Using the Help ..................................................... 69
Problems Solving................................................ 71
Abnormal ................................................................................... 71 Reading the Indicators........................................................ 71Power indicator lights red .......................................................... 71
Warning...................................................................................... 72
Lamp or Temp indicator flashes orange .................................... 72
Normal ....................................................................................... 73
Power indicator lights green or orange/
flashes green or orange .............................................................. 73 When the Indicators Provide No Help .............................. 74Problems relating to images ...................................................... 75
Problems when projection starts ................................................ 81
Other problems .......................................................................... 82 
						

							69
Using the HelpIf a problem occurs with the projector, the Help function uses on-screen 
displays to assist you in solving the problem. It uses a series of menus in a 
question and answer format.
PROCEDURE
Press the [Help] button.
The help menu will be displayed.Select a menu item.
Tilt the [ ] button on the remote control or press the [ ] and 
[ ] buttons on the projectors control panel to select an item.
Confirm the selection.
Press the [Enter] button to confirm the selection of a menu item.
1
Projector
Remote control
2
Remote controlProjector
3
Remote control Projector