Epson Projector EMP-400W User Manual

Security Functions
21
fEntering the Password
When the password entry screen is displayed, enter the password using the 
numeric buttons on the remote control.Enter the password by using the numeric buttons.When you enter the correct password, projection begins.
Procedure
Attention If an incorrect password is entered three times in succession, the 
message The projectors operation will be locked. is displayed 
for about five minutes, and then the projector switches to standby 
mode. If this happens,...

Security Functions
22
Restricting Operation (Operation Lock)
Do one of the following to lock the operation buttons on the control panel.

All of the buttons on the control panel are locked. You cannot perform 
any operations from the control panel, including turning the power on or 
off.
 Operation Lock
All of the buttons on the control panel, except for the [t] button, are 
locked.
This is useful at events or shows when you want to deactivate all buttons 
and only project, or at schools when you want to...

Security Functions
23
Anti-Theft Lock
As the projector is often setup on ceiling mounts and left in rooms 
unattended, it is possible that someone may try and take the projector, so 
the projector includes the following security devices.
 Security slot
The security slot is compatible with the Microsaver Security System 
manufactured by Kensington. You can find details about the Microsaver 
Security System on the Kensington homepage
http://www.kensington.com/
.
 Security cable installation point
A...

Configuration MenuThis chapter explains how to use the configuration menu and its functions.Using the Configuration Menu .......................... 25
List of Functions ................................................. 26
 Image Menu .......................................................................26
 Signal Menu .......................................................................27
 Settings Menu ....................................................................28
 Extended Menu...

25
Using the Configuration Menu
A
Selecting from the 
top menu
C
Changing the 
selected item
B
Selecting from the 
sub menu
Top menu
Sub menu (Settings) Guide
Select the setting to change
Using the remote controlUsing the control panel
Buttons used
D
Exit 

26
List of FunctionsImage Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each 
image signal.
Sub Menu
Function
Color Mode
You can select the quality of the image to suit your surroundings. sp.13
Brightness
You can adjust the image brightness. 
Contrast
g
You can adjust the difference between light and shade in the images. 
Color Saturation
You can adjust the color saturation for the images....

List of Functions
27
Signal Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each 
image signal.
Sub Menu
Function
Auto Setup
You can select whether the image is automatically adjusted to the optimum state (On) or not (Off) when the input signal changes. sp.44
Resolution
When Auto is set, the resolution of the input signal is determined automatically. When Wide is set, all input signals are...

List of Functions
28
Settings Menu
Sub Menu
Function
Keystone
You can correct vertical keystone distortion in images.sQuick Start Guide
Zoom
Adjusts image size. (Tele/Wide)
Operation Lock
You can use this to restrict operation of the projectors control panel. sp.22
Brightness Control
You can set the lamp brightness to one of two settings. 
Select Low if the images being projected are too bright such as when projecting images in a dark room or onto a small screen. When Low is 
selected, the amount of...

List of Functions
29
Extended Menu
Sub Menu
Function
Display
You can make settings related to the projectors display. 
Messages: You can set whether to display (On) or not display (Off) the source name when you change the input source, the color mode name 
when you change the Color Mode, a message when no image signal is input, and so on. 
Display Background
*1: You can set the screen status for when no image signal is available to Black, Blue, or Logo. 
Startup Screen
*1: You can set whether the startup...

List of Functions
30
Language
You can set the language for message displays. 
Reset
You can reset Display
*1 and Operation
*2 in the Extended menu to their default settings. 
To return all menu items to their default settings, see sp.35
*1 When Users Logo Protect is set to On in Password Protect, settings concerning users logo cannot be changed. You can make changes after setting Users 
Logo Protect to Off. sp.20
*2 Except for High Altitude Mode. 
Sub Menu
Function