Epson Projector Elp 3300 User Manual

22 2  •  Using the Projector
If you need to raise or lower the image on the screen, extend or retract the two
feet at the bottom of the projector as follows:
1. Stand behind the projector and support the front of it while you press the
purple release buttons located above the feet. This unlocks the feet so they
can move up and down freely. Do not let the projector drop.
u
Caution: Do not hold the projector by its lens. This can damage the lens.
2. While pressing the release buttons, raise or lower the...

23
Controlling the Projector
Normally you control the projector using the remote control. The buttons on the
remote control allow you to do the following:
• Switch between the computer and video images
• Adjust the brightness, volume, and synchronization
• Turn standby mode on or off
• Access the menus to adjust the image, audio, video, or display settings
(described in Chapter 3)
• Control your computer (described in Chapter 4).
The functions of the remote control buttons are summarized on page 25.
To...

24 2  •  Using the Projector
Menu Standby
CustomPrev. Next
+
Sync Bright
Drag
LR Menu
Select
AdjustVideo
Vol. Freeze MuteLight-
+-
- -+
+
Standby
MenuMenu
SelectFunction
Select
- Bright +
Function
Adjust _
+-   Vol   +
- Sync +
Freeze Mute Video 

25
Button/component Function
Standby Turns standby mode on or off.
Prev,  Next* Control the computer (see Chapter 4).
MenuDisplays or hides the menus.
CustomSelects one of four functions: pattern (default), serial, blank, or
prompt. See Chapter 3 to assign the function.
VideoSwitches between the computer image and video source.
Freeze Freezes or unfreezes the image.
Mute Turns off the sound.
Light Illuminates buttons for 10 seconds or until you press a button
or use the trackball. Pressing again keeps...

26 2  •  Using the ProjectorAdjusting the settings from ELP Link
If you set up the projector for serial communication as described in Chapter 1,
you can use the ELP Link program to control the projector from your computer.
To start ELP Link, do one of the following:
• Windows. Open the ELP Utilities program group by double-clicking on its
icon. Then double-click the ELP Link icon.
• Macintosh. Open the ELP Utilities folder by double-clicking on its icon.
Double-click the ELP Link folder icon and then...

27
The buttons on the right side of the screen allow you to control the projector
settings as you do with the remote control. See the table on page 25 for a
description of these buttons. The buttons on the left allow you to access the
menus. For more information about the menus, see Chapter 3.
Monitoring the Projector
The three lights at the top of the projector monitor its operating status:
lamp light temperature light power light
Under normal circumstances the power and lamp lights are green and the...

28 2  •  Using the ProjectorUsing Rear Projection
The projector can be set up for front or rear projection. In rear projection, the
projector is on the opposite side of the screen from the audience, as shown here:For rear projection, you must turn on the Rear setting in the Display menu. This
setting flips the image from left to right for correct viewing. See Chapter 3 for
information about the menus.
Because the screen is between the remote control and the projector for rear
projection, you need the...

29
3Using the Menus
T
he projector menus allow you to do the following:
• Control the brightness, contrast, sharpness, and color of the image.
• Adjust the vertical or horizontal position of the display, change the placement
of the menus, and configure the display for rear projection or an upside down
ceiling mount.
• Adjust audio settings such as volume, balance, bass, and treble.
• Adjust the display by rotating or inverting it and modifying the color.
• Change the language used in the menus and...

30 3  •  Using the MenusAccessing the Menus
You can display menus on the projector screen or on your computer. To display
menus on top of the projector screen, press the Menu button on the remote
control or the operation panel. This opens the currently selected menu. Other
menus are available from the menu bar at the bottom of the menu.The following table shows the settings for each of the menus:Menu Settings
Computer Brightness, Contrast, Sync, Tracking, Red, Green, Blue, Text
(PC only), Mac LC...

31
Accessing the Menus
To select a different menu, press the Menu Select button on the remote control
or operation panel. To select a setting in the menu, use the trackball (remote
control) or the Function Select buttons (operation panel).
To close the menus, again press the Menu button.
Changing menu settings
Menu settings are sliders with increasing and decreasing values or checkboxes
you turn on or off. A checkbox is on when it is shown with a checkmark.
                       To change a slider...