Epson Projector EH-TW9300W User Manual

Preparing
20
When using a commercially available computer cable
When using a commercially available HDMI cable
Connecting External Equipment
Connecting to the Trigger Out port
To connect external devices such as motorized screens, connect a mini-jack stereo cable (3.5 mm) to the
Trigger Out port. When set to on, a signal (12 V DC) is output from this port to communicate the projector's
status (On or Off) to connected devices such as electric screens.
c
When using the Trigger Out port, set Trigger Out...

Preparing
21
You can operate smartphones or tablets from the projector remote control. You can also view video and
listen to music while charging a smartphone or tablet.
Attention
•Make sure the connection cable supports the MHL standards. During charging, the smartphone or tablet
could generate heat, cause a liquid leak, explode or generate other conditions that could result in a fire.
•When a connection is made using an MHL-HDMI conversion adapter, it may not be possible to charge or
control the device...

Preparing
22
You can use one of the following methods to project over wireless LAN. For more details, see the download
page.
•Projecting four screens simultaneously
When using EasyMP Multi PC Projection, you can display up to four separate screens from the projector from up to
50 computers connected to the network. 
Download EasyMP Multi PC Projection from the following Web site.
http://www.epson.com
•Projecting images from a mobile terminal via a network
By installing "Epson iProjection" on a...

Preparing
23
Preparing the Remote Control
Installing the Remote Control Batteries
Attention
•Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the
correct way.
•You cannot use other batteries except for the AA size manganese or alkaline.
a
Remove the battery cover.
While pushing the battery compartment
cover catch, lift the cover up.
b
Replace the old batteries with new
batteries.
Check the polarity of the batteries (+) and
(-) before installing....

Preparing
24
Operating range (left to right)
N
N

Basic Operations
25
Projecting Images
Turning On the Projector
a
Connect the equipment to the
projector.
b
Connect using the power cord
supplied.
The projector's power indicator turns blue.
This indicates that the projector is receiving
power, but is not yet turned on (it is in
standby mode).
c
Turn on the connected equipment.
d
Press the  button on the remote
control or the 
 button on the
control panel to turn on the projector.
Remote control Control panel
The lens shutter opens, and projection...

Basic Operations
26
If the target image is not projected
If the image is not projected, you can change the source using one of the following methods.
Remote control Control panel
Press the button for the target port.
Press the  button and select the target port.
Press the 
 button to confirm the selection.
Using the Home Screen
The Home screen feature allows you to easily select an image source and access useful functions.
Press the 
 button on the remote control to display the Home screen.
Under the...

Basic Operations
27
c
The Home screen disappears after 10 minutes of inactivity.
Turning Off
a
Turn off the connected equipment.
b
Press the  button on the remote
control or the 
 button on the
control panel.
Remote control Control panel
A confirmation message is displayed.
c
Press the  button again.
Projection ends, and the lens shutter closes
automatically.
The operation indicator flashes and the
projector begins to cool down.
d
Wait until cool-down is complete.
When cool-down is complete, the...

Basic Operations
28
Adjusting the Projected Image
Displaying the Test Pattern
When adjusting the zoom/focus or the projection position just after setting up the projector, you can display
a test pattern instead of connecting video equipment.
Press the 
 button on the remote control to display the test pattern. The standard for horizontal lines
at the top and bottom uses 2.40:1 CinemaScope.
When you select Color Isolation while projecting images, the color selected from R (red), G (green), or B (blue)
is...

Basic Operations
29
Adjusting the focus
a
Press the  button on the remote control.
Adjust Focus is displayed on the screen.
b
Press the  buttons to adjust the focus.
c
Press the  button three times to finish making adjustments.
Adjusting the projection size (Zoom Adjustment)
a
Press the  button on the remote control twice.
Adjust Zoom is displayed on the screen.
b
Press the  buttons to adjust the size of the projected screen.
c
Press the  button twice to finish the adjustment.