Epson Projector EH TW9300 User Manual

							Appendix
120
Signal Refresh Rate (Hz) Resolution (dots)
4K x 2K 24/25/30 3840 x 2160
4K x 2K (SMPTE) 24 4096 x 2160
*1HDMI4 port only
*2When projecting in WirelessHD, the following signals are not supported.
4K x 2K(SMPTE): 24 Hz 
						

							Appendix
121
Specifications
Product nameEH-TW9300W/EH-TW9300/EH-TW8300W/EH-TW8300/EH-TW7300
Appearance520 (W) x 170 (H) x 450 (D) mm (not including adjustable foot)
Panel Size0.74" wide
Display methodPolysilicon TFT active matrix
Resolution1920 (W) x 1080 (H) x 3
Focus adjustmentMotorized
Zoom adjustmentMotorized (Approx. 1 to 2.1)
Lamp (light source)UHE lamp 250 W, Model No.: ELPLP89
Lamp replacement time3400 hours
Power supply100 - 240 V AC ±10%, 50/60 Hz, 3.8 - 1.7 A
Power con-
sumption100 to 120 V areaRated power consumption: 373 W
Standby power consumption (Communication On): 2.3 W
Standby power consumption (Communication Off): 0.27 W
220 to 240 V areaRated power consumption: 355 W
Standby power consumption (Communication On): 2.4 W
Standby power consumption (Communication Off): 0.35 W
Operating altitudeAltitude 0 to 3,000 m
Operating temperature+5 to +35°C * (No condensation)
Storage temperature-10 to +60°C (No condensation)
MassApprox. 11 kg
*The operating temperature is +5 to +30°C at an altitude of 2287 to 3000m.
 
Connectors PC port 1Mini D-Sub15-pin (female) blue
HDMI port 2For HDMI HDCP2.2 (HDMI1 port only), for CEC sig-
nals, for 3D signals, Deep Color
RS-232C port 1Mini D-Sub 9-pin (male)
Trigger Out port 1Stereo mini jack (3.5Φ)
LAN port 1RJ-45
Service port*1USB connector (Type B)
USB port*1USB connector (Type A)
USB port (for Opt.HDMI
power supply)
*1
*Supports USB 2.0. However, USB ports are not guaranteed to operate all devices that support USB.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.  
						

							Appendix
122 Обладнання відповідає вимогам Технічного регламенту обмеження використання деяких небезпечних
речовин в електричному та електронному обладнанні.
Angle of tilt
If you use the projector tilted at an angle of more than 3°, it could be dam-
aged or cause an accident. 
						

							Appendix
123
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We: Epson America, Inc.
Located at: 3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
Tel: 562-981-3840
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the
FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and
found to be compliant with the standards. Records maintained continue to reflect the equipment being
produced can be expected to be within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trade Name: EPSON
Type of Product: LCD Projector
Model: H710C/H711C/H713C/H714C/H715C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment. 
						

							Appendix
124
Appearance
Units: mm


B

 
aCenter of lens
b Distance from center of lens to suspension bracket fixing point

 .Y -&/4

 
 
 
						

							Appendix
125
List of Safety Symbols
The following table lists the meaning of the safety symbols labeled on the equipment.
Symbol mark Approved stand-
ardsMeaning
IEC60417
No. 5007"ON" (power)
To indicate connection to the mains.
IEC60417
No. 5008"OFF" (power)
To indicate disconnection from the mains.
IEC60417
No. 5009Stand-by
To identify the switch or switch position by means of which part
of the equipment is switched on in order to bring it into the stand-
by condition.
ISO7000
No. 0434B
IEC3864-B3.1Caution
To identify general caution when using the product.
IEC60417
No. 5041Caution, hot surface
To indicate that the marked item can be hot and should not be
touched without taking care.
IEC60417
No. 6042
ISO3864-B3.6Caution, risk of electric shock
To identify equipment that has risk of electric shock.
IEC60417
No. 5957For indoor use only
To identify electrical equipment designed primarily for indoor
use.
IEC60417
No. 5926Polarity of d.c. power connector
To identify the positive and negative connections (the polarity)
on a piece of equipment to which a d.c. power supply may be
connected.
---
IEC60417
No. 5001BBattery, general
On battery powered equipment. To identify a device for instance
a cover for the battery compartment, or the connector terminals.
IEC60417
No. 5002Positioning of cell
To identify the battery holder itself and to identify the positioning
of the cell(s) inside the battery holder.
---
IEC60417
No. 5019Protective earth
To identify any terminal which is intended for connection to an
external conductor for protection against electric shock in case
of a fault, or the terminal of a protective earth electrode.
IEC60417
No. 5017Earth
To identify an earth (ground) terminal in cases where neither the
symbol 
 is explicitly required. 
						

							Appendix
126
Symbol mark Approved stand-
ardsMeaning
IEC60417
No. 5032Alternating current
To indicate on the rating plate that the equipment is suitable for
alternating current only; to identify relevant terminals.
IEC60417
No. 5031Direct current
To indicate on the rating plate that the equipment is suitable for
direct current only; to identify relevant terminals.
IEC60417
No. 5172Class II equipment
To identify equipment meeting the safety requirements specified
for Class II equipment according to IEC 61140.
ISO 3864 General prohibition
To identify actions or operations that are prohibited.
ISO 3864 Contact prohibition
To indicate injury that could occur due to touching a specific part
of the equipment.
--- Never look into the projection lens while the projector is on.
--- To indicate that the marked item don't place anything on pro-
jector.
ISO3864
IEC60825-1Caution, laser radiation
To indicate the equipment has a laser radiation part.
ISO 3864 Disassembly prohibition
To indicate a risk of injury, such as electric shock, if the equipment
is disassembled.
--- Never look into the lens while the LED for lighting is on.
IEC60417
No. 5266Standby, partial standby
To indicate that part of the equipment is in the ready status.
ISO3864
IEC60417
No. 5057Caution, movable parts
To indicate that you must keep away from movable parts ac-
cording to protection standards. 
						

							Appendix
127
Maximum radio-frequency power transmitted
Models
H711B WiT4-G0
WirelessHD Transmitter 60.16275-60.95725 GHz
-32dBm
e.i.r.p.
WirelessHD Receiver 60.16275-60.95725 GHz 27dBm
e.i.r.p.
-
4k Wireless Transmitter 60.16275-60.95725 GHz-32dBm
e.i.r.p.
4k Wireless Receiver 60.16275-60.95725 GHz 27dBm
e.i.r.p.
- 
						

							Appendix
128
Glossary
This section briefly explains the difficult terms that are not explained in context in the text of this guide. For
details, refer to other commercially available publications.
Aspect RatioThe ratio between an image's length and its height. Screens with a horizontal:vertical ratio
of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
HDCPHDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to pre-
vent illegal copying and protect copyrights by encrypting digital signals sent over DVI and
HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital
images protected by HDCP technology. However, the projector may not be able to project
images protected with updated or revised versions of HDCP encryption.
HDMI™
An abbreviation for High Definition Multimedia Interface. This is the standard by which
HD images and multichannel audio signals are digitally transmitted.
HDMI
™ is a standard aimed at digital consumer electronics and computers. By not com-
pressing the digital signal, the image can be transferred at the highest quality possible. It
also provides an encryption function for the digital signal.
HDTVAn abbreviation for High-Definition Television. This refers to high-definition systems
which satisfy the following conditions.
•Vertical resolution of 720p or 1080i or greater (p = Progressive, i = Interlace)
•Screen aspect of 16:9 Dolby Digital audio reception and playback (or output)
InterlaceTransmits information needed to create one screen by sending every other line, starting
from the top of the image and working down to the bottom. Images are more likely to
flicker because one frame is displayed every other line.
MHLAn abbreviation for Mobile High-definition Link, which is a standard high-definition in-
terface that enables high-speed transfer of video signals on mobile devices.
It is a standard targeting smartphones and tablets that transfers uncompressed digital
signals without loss of quality and also enables simultaneous charging of such devices.
PairingRegister devices in advance when connecting with Bluetooth devices to ensure mutual
communication.
SDTVAn abbreviation for Standard Definition Television. This refers to standard television sys-
tems which do not satisfy the conditions for HDTV High-Definition Television.
SVGAA screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
SXGAA screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
VGAA screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGAA screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
YCbCrIn component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the
color difference.
YPbPrIn component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the
color difference. 
						

							Appendix
129
General Notes
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting from the use of the infor-
mation contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original Epson Products or Epson Approved Prod-
ucts by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related
to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/
precision devices etc, you should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because this product was not
intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main
communication equipment, nuclear power control equipment, or medical equipment related to direct medical
care etc, please make your own judgment on this product’s suitability after a full evaluation.