Epson Projector Eb S6 User Manual

Problem Solving
61
fOther problems
f
There is no audio or the audio is too low
f
The remote control does not work
Check
Remedy
Is the audio source connected correctly?
Check that the cable is connected to the Audio port. 
Is the volume adjusted to the minimum setting?
Adjust the volume so that sound can be heard.
Is A/V Mute active?
Press the [A/V Mute] button on the  remote control to cancel A/V Mute.  sp.22
Is the audio cables specification No resistance?
When using a commercially available audio cabl...

AppendicesThis chapter provides information on maintenance procedures to ensure the  best level of performance from the 
projector for a long time to come. Installation Methods ........................................... 64
Cleaning................. .............................................. 65
 Cleaning the Projectors Surf ace .....................................65
 Cleaning the Lens ... ...........................................................65
 Cleaning the Air Filter and  Air Intake Vent...

Using Slideshow (EB-W6 only) .......................... 90
 Image Files that can be Projected in a Slideshow ..........90
 Basic Slideshow Operations ... ..........................................90
Starting Slideshow........................................................................\
.. 90
Exiting Slideshow.......................................................\
.................... 91
Slideshow file brow ser screen ........................................................ 91
Playing individua l...

64
Installation MethodsThe projector supports the following four different projection methods.  
Install according to th e conditions of the installation location. 
 Wa r n in g
 A special method of in stallation is required when suspending the 
projector from a ceiling (ceiling mount). If it is not installed 
correctly, it could fall causing an accident and injury.
 If you use adhesives on the ceiling mount to prevent the screws  from loosening, or if you use things such as lubricants or oils on 
the...

65
CleaningYou should clean the projector if it becomes dirty or if the quality of 
projected images starts to deteriorate.Cleaning the Projectors Surface
Clean the projectors surface by wi ping it gently with a soft cloth.
If the projector is particularly  dirty, moisten the cloth with water 
containing a small amount of neutral de tergent, and then firmly wring the 
cloth dry before using it to  wipe the projectors surface.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to...

66
Replacing ConsumablesThis section explains how to replace the remote control batteries, the 
lamp, and the air filter. Replacing the Remote Control Batteries
If delays in the responsiveness of the  remote control occur or if it does not 
operate after it has been used for so me time, it probably means that the 
batteries are becoming flat.  When th is happens, replace them with new 
batteries. Have two spare AA-size al kaline or manganese dry batteries 
ready to use. You can only use AA -size...

Replacing Consumables
67
C
Replace the battery cover. Press the battery cover until it clicks into place.
Replacing the LampfLamp replacement period
It is time to replace the lamp when:
 The message Replace the  lamp. is displayed.  The lamp indicator flashes orange.
 The projected image gets darker 
or starts to deteriorate.
EB-W6 EB-X6/S6
A message is displayed. 
Flashing orangeThe illustration is of the EB-W6. 

Replacing Consumables
68
fHow to replace the lamp
Attention The lamp replacement message is  set to appear after the following 
time periods in order to maintain  the initial brightness and quality 
of the projected images. 
s
Brightness Control  p.43
- When used continually at high brightness: About 2900 hours
- When used continually at low brightness: About 3900 hours
 If you continue to use the lamp  after the replacement period has 
passed, the possibility that the lamp  may explode increases. When...

Replacing Consumables
69
A
After you turn off the projectors power and the 
confirmation buzzer beeps twice, disconnect the 
power cable. 
B
Wait until the lamp has  cooled down, then remove 
the lamp cover. Loosen the lamp cover fixing screw  with the screwdriver supplied 
with the new lamp or a + head screwdriver. Then slide the lamp 
cover straight forward and lift it to remove. 
C
Loosen the two lamp fixing screws.
D
Take out the old lamp.If the lamp is cracked, replace it  with a new lamp, or...

Replacing Consumables
70
E
Install the new lamp.Insert the new lamp along the guide rail in the correct direction so 
that it fits in place, push down  firmly at the location marked 
PUSH, and once it is fully inserted tighten the two screws.
F
Replace the lamp cover.
f Resetting the lamp operating time
The projector records how long the lamp is turned on and a message and 
indicator notify you when it is time  to replace the lamp.  After replacing 
the lamp, make sure you reset the la mp hours in the...