Epson Projector BrightLink 536Wi User Manual

4. Connect the stereo mini-jack end of the cable to your projectors
Audio Outport.
Parent topic: Projector Connections
Related references
Projector Setup Settings - Extended Menu
Connecting a Microphone You can connect a microphone to the projectors Micport to provide audio support during presentations.
Note: The projector supports powered or dynamic microphones only. If you want to output audio from
the microphone when the projector is turned off, you need to select Communication Onfor the
Standby Mode...

Connecting to External USB Devices
Follow the instructions in these sections to connect external USB devices to the projector.
USB Device Projection
Connecting a USB Device or Camera to the Projector
Selecting the Connected USB Source
Disconnecting a USB Device or Camera From the Projector
Parent topic:Projector Connections
USB Device Projection You can project images and other content without using a computer or video device by connecting any of
these devices to your projector:
• USB flash drive
•...

Connecting a USB Device or Camera to the Projector
You can connect your USB device or camera to the projectors USB-Aport and use it to project images
and other content.
1. If your USB device came with a power adapter, plug the device into an electrical outlet.
2. Connect the USB cable (or USB flash drive or USB memory card reader) to the projectors USB-A
port.
Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not
operate correctly.
3. Connect the other end of the...

Disconnecting a USB Device or Camera From the Projector
When you finish presenting with a connected USB device or camera, you must prepare to disconnect the
device from the projector.
1. If the device has a power button, turn off and unplug the device.
2. Disconnect the USB device or camera from the projector.
Parent topic:Connecting to External USB Devices
Connecting to a Document Camera You can connect an Epson document camera to your projector to project images viewed by the camera.
Depending on your...

1. Connect one end of the remote control cable to the
SYNC Inport on one projector, and connect the
other end to the SYNC Outport on the other projector.
Note: If you are connecting three or more projectors, connect the projectors in a chain as shown.
2. In the Extended menu, set the Sync of Projectorssetting toWired.
Note: If you are using the projector in the same room as another projector that does not support
cable connection or if you do not have the optional remote control cable, set the Wired Sync...

1. Remove the battery cover.
2. Insert the batteries with the
+and –ends facing as shown.
46   

3. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
Installing Batteries in the Pen The pen uses one AA battery.
1. Remove the battery cover as shown.
47   

2. Insert the battery with the
+and –ends facing as shown.
3. Replace the battery cover and press it down until it clicks into place.
Parent topic: Setting Up the Projector
48   

Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Projection
Wireless Network Projection
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Controlling a Networked Projector Using a Web Browser
Crestron RoomView Support
Wired Network Projection You can send images to your projector through a wired network. To do this, you connect the projector to
your network, and then set up your projector and...

Note:
If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly through the access point using the EasyMP Network
Projection software.
Connecting to a Wired Network
Selecting Wired Network Settings
Parent topic: Using the Projector on a Network
Related references
Projector Network Settings - Network Menu
Connecting to a Wired Network To connect the projector to a wired local area network (LAN), use a 100Base-TX or...