Epson Powerlite Pro G5950nl Users Guide

							5
111
5
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image, 
sound, and other features. This chapter covers the following 
information:
■Using the menu system
■Adjusting the image
■Adjusting signal settings
■Customizing projector features
■Using the projector security features
■Customizing power and operation
■Multi-screen color adjustment
■Projector Menu and Options List 
						

							112Fine-Tuning the Projector
Using the Menu System
You can use the remote control or the projector’s control panel to 
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the 
Menu button on the 
remote control or on the projector.
You see a menu screen similar to the one below: 
The menus are listed on the left and the options available for the 
highlighted menu are shown on the right.
2. Use the  pointer button on the remote control (or the 
navigational buttons on the projector) to scroll through the menu 
list. When you’ve highlighted the desired menu, press the 
Enter 
button to select it. 
3. Once you’ve selected the menu, use the  pointer button to 
scroll through the list of options. (Some of the options may be 
grayed out or unavailable, depending on the selected source.)
Menu list
Options
note
For a complete list of menus 
and options, see page 129. 
For more information on 
these menus and options, 
continue reading this 
chapter. 
						

							Fine-Tuning the Projector113
4. After highlighting the option you want to adjust, use the 
pointer button to change the setting. In some cases, you may 
have to press the 
Enter button to view a sub-screen for changing 
the setting. 
■Press the left or right side of the  pointer button to adjust
a slider bar.
■To select from two or more settings, use the  pointer 
button to highlight the desired setting and press 
Enter. 
5. After changing the settings, press the 
Esc button to save your 
changes and return to the previous menu (or press it repeatedly to 
exit the menu system). 
You can also press the 
Menu button to exit. 
Restoring the Default Settings 
You can use the menu system’s Reset options to restore the factory-
default settings for all the settings listed in a specific menu, or all the 
settings in all menus.
To restore the settings in a specific menu, enter the menu whose 
settings you want to change, select 
Reset, and confirm as needed. 
(The example below shows how to reset the Image menu.) 
To restore all the projector settings to their factory-default values, 
select the 
Reset menu, highlight Reset All, and press Enter. 
Reset settings
for current menu
Reset settings for
all menusnote
When you select Reset All 
in the Reset menu, it does 
not reset the Input Signal, 
User’s Logo, Multi-screen, 
Language, Lamp Hours, or 
Network settings. 
						

							114Fine-Tuning the Projector
Adjusting the Image 
You can use the Image menu to adjust the brightness, sharpness, color, 
tint, and contrast. 
1. Press the 
Menu button on the projector or remote control and 
select the 
Image menu.
You see a screen similar to one of those below. (The settings will 
be different depending on the source you are projecting from.)
2. Use the  pointer button to highlight the desired option, then 
adjust it as needed:
■Color Mode
Lets you quickly adjust the color and brightness for various 
environments. Use either the remote control or the 
Color 
Mode
 setting in the Image menu. You can save a different 
setting for each source. See page 60 for more information on 
each color mode.
■Brightness 
Lightens or darkens the overall image. 
■Contrast
Adjusts the difference between light and dark areas. 
■Color Saturation
Adjusts the color depth of the image. 
■Tint
Adjusts the balance of green to magenta in the image. 
Computer/RGB Video/
USB/LANComponent Video/
Composite Video/
S-Video
note
The available settings vary 
depending on the input 
source selected.
note
The Brightness setting 
changes the opacity of the 
projector’s LCD panels. You 
can also use the 
Power 
Consumption
 setting to 
change the lamp’s brightness 
(see page 119). 
						

							Fine-Tuning the Projector115
■Sharpness
Adjusts the sharpness of the image.
If you select 
Advanced, you can access more detailed 
settings: Adjust 
Thin Line Enhancement to enhance or 
soften objects like hair or fabric patterns. Adjust 
Thick Line 
Enhancement
 to enhance or soften outlines of objects or 
backgrounds. Adjust 
Vert. Line Enhancement to enhance 
vertical lines in the image. Adjust 
Horiz. Line Enhancement 
to enhance horizontal lines in the image.
■Abs. Color Temp.
Sets a color temperature between 5000 and 10000 °K. (Not 
available if 
sRGB is selected as the Color Mode setting.) 
■Color Adjustment
Adjusts the color values. For Customized color mode, select 
R, G, B, C, M, Y to adjust individual red, green, blue, cyan, 
magenta, and yellow hue, saturation, and brightness values. 
For other color modes, RGB may be selected to adjust red, 
green, and blue saturation values. (Not available if 
sRGB is 
selected as the Color Mode setting.)
Six-Axis Color Adjustment
For special projection material, such as high-quality photographs or 
artwork, you can adjust the hue, saturation, and brightness for six 
different color axes. 
1. Follow the instructions on page 114 to open the Image menu and 
select 
Color Mode.
2. Press the 
Enter button to select Customized, then press Esc to 
return to the Image menu.
3. Select 
Color Adjustment and press Enter. You see hue, 
saturation, and brightness controls on the screen for six colors: 
R, 
G, B, C, M, Y
 (red, green, blue, cyan, magenta, and yellow).
4. Select the color axis you want to adjust and press 
Enter. You see 
color controls for hue, saturation, and brightness. 
Hue changes the balance of color, and saturation changes the 
strength of the color.
note
You cannot adjust the 
advanced Sharpness settings 
if the input signal is RGB or 
if the input source is   
USB or LAN. 
						

							116Fine-Tuning the Projector5. Use the  pointer button to adjust the hue, saturation, and 
brightness. You see the adjustments reflected on the screen. When 
you are satisfied with the color, press 
Esc.
6. Repeat steps 4 and 5 for each color axis you want to adjust.
You may need to readjust the color as the lamp in your projector 
changes over time.
Adjusting Signal Settings
Although the projector normally detects and optimizes the input 
signal automatically, you can use the Signal menu to make manual 
adjustments. In addition to changing the position of the projected 
image, you can correct tracking and sync for computer images, or 
change the aspect ratio to widescreen format for video images. 
1. Press the 
Menu button and select the Signal menu. 
You see a screen similar to one of those below. (The settings will 
be different depending on the source you are projecting from.)
2. Use the  pointer button to highlight the desired option, then 
adjust it as needed:
■Auto Setup 
Leave this setting 
On to automatically optimize computer 
images. Turn it off if you want to save adjustments you have 
made to the Tracking, Sync, and Position settings.
Computer/RGB Video
Component Video 
						

							Fine-Tuning the Projector117
■Resolution
Set to Auto to have the projector automatically identify the 
resolution of the input signal. If necessary (because some of 
the image is missing, for example), adjust to 
Wide or 
Normal. You can also select Manual and specify a resolution.
■Tracking 
Adjust this value to eliminate vertical stripes in computer 
images.
■Sync
Adjust this value if computer images appear blurry or flicker.
■Position
If the image is slightly cut off on one or more sides, it may not 
be centered exactly. Select this setting and use the  pointer 
button to center it.
■Progressive
For composite video, S-Video, component video, and signals 
from the HDMI port only. Turn this setting on to convert 
interlaced signals into progressive signals (best for still 
images). Select 
Video for viewing general video images. Select 
Film/Auto for movie images, CG, and animated images. 
Leave the setting 
Off for moving images.
■Noise Reduction
Smooths out rough images. Select the setting that makes the 
selected input source look best. Epson recommends that you 
select 
Off when viewing image sources with very low noise, 
such as DVDs.
■HDMI Video Range (G5550NL/G5650WNL/G5950NL 
only)
When you connect to the HDMI input port, set the 
projector’s video range to match the video range setting of 
your device.
■DVI/HDMI Video Range (G5450WUNL/G5750WUNL 
only)
When you connect to the DVI-D or HDMI input port, set 
the projector’s video range to match the video range setting of 
your device.
note
You can also use the remote 
control’s 
Auto button to 
automatically reset the 
projector’s Tracking, Sync, 
and Position settings. See 
page 155 for details.
note
For component or RGB 
video, the Progressive setting 
can only be adjusted when 
480i/576i/1080i signals are 
being input. However, the 
setting cannot be adjusted 
with 1080i signals when the 
Aspect setting is Full.
note
The Noise Reduction, 
Progressive, and Overscan 
settings cannot be set for 
digital RGB signals. 
						

							118Fine-Tuning the Projector
■Input Signal
If the colors don’t look right on the Auto setting, select the 
setting for the type of equipment you’ve connected to the 
Computer1, Computer2 (G5550NL/G5650WNL/
G5950NL only), or 
BNC ports. Choose RGB for a computer 
or RGB-video connection, and 
Component for a video 
player that outputs a component video signal (with 
connectors labeled Y/Cb/Cr or Y/Pb/Pr).
■Video Signal 
Select the setting for the type of equipment you’ve connected 
to the 
Video1, Video2, or S-Video ports. Leave this setting 
at 
Auto unless you are using a 60-Hz PAL system (then select 
PAL60).
■Aspect
Sets the image’s aspect ratio (ratio of width to height). 
Depending on your projector model and input source, you 
can select 
Auto, Normal, 4:3, 16:9, Full, Zoom, or Native; 
see page 61 for more information.
■Overscan
Allows you to reduce the image size slightly when the edges of 
the image are not visible. The range of trimming can be set to 
Off, 4%, or 8%. You can select Auto only when the input 
source is 
HDMI. When Auto is selected, the range is 
automatically switched to 
Off or 8% according to the input 
signal.
■2-2 Pull-down (G5450WUNL/G5750WUNL only)
Projects 24 frames per second images at their original frame 
rate without interpolation. This can be set only when 
1080p/24Hz signals are being input. 
						

							Fine-Tuning the Projector119
Customizing Projector Features
You can use the Settings menu to lock the buttons on the projector, 
adjust audio volume, and customize several other features.
■Keystone 
Adjusts the shape of the image if the projector has been tilted 
upward or placed at an angle to the screen.
Select 
H/V-Keystone to correct horizontal and vertical keystone 
distortion.
Select 
Quick Corner to adjust the shape and position of the 
projected image.
■Split Screen
Lets you divide the screen into two parts and show two input 
sources at the same time. See page 62 for more information.
■Control Panel Lock
Lets you disable all of the buttons on the projector, or all of the 
buttons except the Ppower button. See page 125 for more 
information.
■Pointer Shape
Lets you choose from three pointer shapes. See page 69 for more 
information.
■Power Consumption
Lets you select from two levels of brightness. The ECO setting 
reduces power consumption and noise, and extends the lamp’s 
operating life. 
						

							120Fine-Tuning the Projector
■Volume
Raises or lowers the volume.
■Audio Input
Lets you select the input port to use for audio when your video 
input is 
LAN. With the PowerLite G5550NL/G5650WNL/
G5950NL, you can also select an audio input port when your 
video input is 
HDMI.
■Remote Receiver
Deactivates the projector’s front and/or back sensors that detect 
signals from the remote control. Use this setting to prevent use of 
the remote control or to stop interference from bright fluorescent 
lights.
■User Button
You can assign one of the following six menus to the User 
button: 
Power Consumption, Info, Progressive, Test 
Pattern
, Multi-screen, or Resolution. By pressing the button, 
the assigned menu item selection/adjustment screen is displayed, 
allowing you to make one-touch settings/adjustments.
■Test Pattern
Displays a test pattern for use when adjusting the zoom, focus, 
image position, 
Color Mode, Brightness, Sharpness (standard 
only), 
Abs. Color Temp, Color Adjustment, and when 
performing keystone correction.
Press the  pointer button on the remote control to the left or 
right or press the 
Enter button on the projector to change the test 
pattern. Press the 
Esc button to clear the test pattern.
note
You can also adjust the 
volume using the remote 
control.