Epson Powerlite Home Cinema 1080 Ub Users Guide

Introduction11
Optional Accessories
Epson provides the following optional accessories for the projector:
You can purchase accessories from an authorized Epson reseller. To find the nearest 
reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit 
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Registration and Warranty
The PowerLite Home Cinema 1080 UB comes with a basic two-year carry-in warranty. For 
details, see page 71.
In addition, for customers who register...

12Introduction
Using This Manual
This book contains all the information you need to use the projector, in addition to basic 
setup and maintenance instructions, troubleshooting tips, important safety instructions, 
specifications, and warranty information.
Please follow these guidelines as you read through the manual:
Warning: Must be followed carefully to avoid bodily injury.
Caution: Must be observed to avoid damage to your equipment.
Note: Contains important information about your projector.
Tip:...

Setting Up the Projector13
Setting Up the Projector
Follow the instructions in this section to choose a location for the projector, connect the 
cables, and display an image.
Choosing a Location
You can install the projector for various viewing setups, as shown below. 
Center
CeilingSide 

14Setting Up the Projector
Ideally, place the projector at a height where its lens is between the top and bottom of the 
screen. That way, you can keep the projector level and use the vertical lens shift dial to 
position the image. This produces the best-looking picture.
Try to be as close as possible to the calculated projector position when installing the projector. 
Too much lens shift can cause minor reduction in image dimensions. The image display 
position cannot be moved to the maximum distance...

Setting Up the Projector15
The maximum size of the image is determined by the distance from the projector’s lens to the 
screen. Depending on your display settings and how you use the Zoom ring, the actual size 
may be smaller. Use this table as a rough guide for projector placement: 
To determine the exact image size when you know the projection distance (or the exact 
projection distance when you know the desired image size), you can use the Projection 
Distance Calculator. You can download this...

16Setting Up the Projector
Also keep these considerations in mind:
■Make sure there is plenty of space for ventilation around and under the projector. Do not 
set the projector on top of loose materials that could block the vents underneath.
■Make sure the projector is within 9.8 feet of a grounded electrical outlet or extension 
cord.
Installing the Projector
To install the projector, you first need to determine the location, based on the size of your 
screen (maximum diagonal image size). Use the table...

Setting Up the Projector17
The following illustrations show the dimensions of the projector:
To install, you will need the optional projector mount designed for the projector. See page 11 
for ordering information.
Warning: When installing or adjusting the ceiling mount, do not use adhesives to prevent the 
screws from loosening and do not use any type of oil or lubricant. These may cause the projector 
casing to crack and the projector may fall, causing serious injury and serious damage to the...

18Setting Up the Projector
In addition to the tools supplied with the projector mount, you will need a Phillips head 
screwdriver and a drill to use on the wall or ceiling.
If you install the projector on the ceiling, you will need to 
invert the picture so that it appears right side up. Follow 
these steps:
1. Press the 
Menu button on the remote control.
2. Press the menu navigation buttons to open the 
Settings menu, then select Projection.
3. Use the navigation buttons to select 
Front/Ceiling.
4....

Setting Up the Projector19
* For details on compatible video formats, see page 63. 
For best results, connect your video equipment to the HDMI1 (High-Definition Multimedia 
Interface) or HDMI2 port, if possible. If your equipment doesn’t support HDMI, connect it 
to one of the following ports (highest quality listed first): Component (for component video), 
S-Video, or Video (for composite video). 
Component  Use a component video cable
(with RCA-style connectors):
Connect the cable to the three...

20Setting Up the Projector
If you connect to the Component port, be sure to select the correct Input Signal setting for 
your equipment, or the image may not display properly (see page 23).
Making Other Connections
Connect the power cable and other cables described below, depending on how you plan to 
use the projector.
■Plug the power cable into the projector and a grounded electrical outlet. 
■The Trigger out port outputs a 12-volt DC signal 
when the projector is turned on. This lets a central...