Epson Powerlite 96w Quick Setup Manual
Have a look at the manual Epson Powerlite 96w Quick Setup Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Connect the projector
Choose from the following connections:
Computer USB Port
Connect a computer using a USB cable.
Connect the square end of the USB cable to the projector’s USB
TypeB (square) port. Connect the flat end of the cable to any USB port on
your computer.
Windows® 2000 SP4 or later: After turning on the projector, follow
the on-screen instructions to install the Epson USB Display software
(EMP_UDSE.EXE; only on first connection).
Note: If the software screen does not display automatically, open My
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not
display, access the projector’s Extended menu and select USB Display as the
USB Type B setting. See the User’s Guide on your projector CD for instructions.
Mac OS® X 10.5.1 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
Connect one end of the cable to the projector’s Computer1 or Computer2
port, and the other end to your computer’s monitor port. If you are using
a notebook, switch it to external display (see “Troubleshooting”). You can also
connect an audio cable.
Wireless Network
You can connect the projector wirelessly over an 802.11g, 802.11b, or 802.11n
wireless network. See “Project wirelessly” for instructions.
Wired Network
You can connect the projector to your network using an Ethernet® cable.
See “Project over a wired network” on the back of this sheet for instructions.
Video Device
Connect up to 5 video devices and use the Source Search button on the
projector or remote control to switch between them. (All cables are optional).
RCA video cable (composite video)
Component video to VGA cable
Audio cable
S-Video cable
Audio cable
HDMI cable
Camera, USB Device, or Epson Document Camera DC-06
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera DC-06 to the projector’s USB TypeA (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the User’s Guide on your projector
CD for details.
External Monitor, External Speakers, and Microphone
You can also connect an external monitor, external speakers, and a microphone
to your projector to enhance your presentations. See the User’s Guide on your
projector CD for details.
Turn on your equipment
1 Turn on your computer or video source.
2 Plug in the projector.
The power light on the projector turns orange.
3 Open the A/V Mute slide all the way.
4 Press thepower button on the projector or remote control.
Power button
Power light
The power light flashes green, then stays on.
Note: To shut down the projector, press thepower button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5 The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select your
language and press Enter. Press the Menu to exit the menu system.
Adjust the image
1 If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2 To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3 Rotate the focus ring to sharpen the image.
Focus ring
4 Turn the zoom ring to reduce or enlarge the image.
Zoom ring
5 If your image looks likeor, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely. Or press the or buttons on
the projector to correct it.
6 If your image looks likeor, press theorbuttons on the
projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which source to display
Turn projectoron and off
Access projector menus
Turn off projector display and sound
Control projector volume
Navigate projector menus
For more information on using the remote control, see the User’s Guide on
your projector CD.
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11g,
802.11b, or 802.11n wireless network. You must install the optional Epson
wireless LAN module (part number V12H418P12). Your computer must have
a wireless card or built-in wireless interface, and be running Windows 7,
Windows Vista®, Windows XP Professional x64, Windows XP, or Windows 2000,
or Mac OS X 10.3 to 10.6.
1 Turn off the projector and unplug the power cord.
2 Slide the air filter cover latch and open the air filter cover.
3 Remove the screw securing the wireless LAN module stopper, then
remove the stopper.
4 Insert the wireless LAN module into the port.
PowerLite® 95/96W/905/915W/1835
4120194 Rev.0
1-F C
4120194 Rev.0
1-F M
4120194 Rev.0
1-F Y
4120194 Rev.0
1-F K
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Connect the projector
Choose from the following connections:
Computer USB Port
Connect a computer using a USB cable.
Connect the square end of the USB cable to the projector’s USB
TypeB (square) port. Connect the flat end of the cable to any USB port on
your computer.
Windows® 2000 SP4 or later: After turning on the projector, follow
the on-screen instructions to install the Epson USB Display software
(EMP_UDSE.EXE; only on first connection).
Note: If the software screen does not display automatically, open My
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not
display, access the projector’s Extended menu and select USB Display as the
USB Type B setting. See the User’s Guide on your projector CD for instructions.
Mac OS® X 10.5.1 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
Connect one end of the cable to the projector’s Computer1 or Computer2
port, and the other end to your computer’s monitor port. If you are using
a notebook, switch it to external display (see “Troubleshooting”). You can also
connect an audio cable.
Wireless Network
You can connect the projector wirelessly over an 802.11g, 802.11b, or 802.11n
wireless network. See “Project wirelessly” for instructions.
Wired Network
You can connect the projector to your network using an Ethernet® cable.
See “Project over a wired network” on the back of this sheet for instructions.
Video Device
Connect up to 5 video devices and use the Source Search button on the
projector or remote control to switch between them. (All cables are optional).
RCA video cable (composite video)
Component video to VGA cable
Audio cable
S-Video cable
Audio cable
HDMI cable
Camera, USB Device, or Epson Document Camera DC-06
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera DC-06 to the projector’s USB TypeA (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the User’s Guide on your projector
CD for details.
External Monitor, External Speakers, and Microphone
You can also connect an external monitor, external speakers, and a microphone
to your projector to enhance your presentations. See the User’s Guide on your
projector CD for details.
Turn on your equipment
1 Turn on your computer or video source.
2 Plug in the projector.
The power light on the projector turns orange.
3 Open the A/V Mute slide all the way.
4 Press thepower button on the projector or remote control.
Power button
Power light
The power light flashes green, then stays on.
Note: To shut down the projector, press thepower button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5 The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select your
language and press Enter. Press the Menu to exit the menu system.
Adjust the image
1 If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2 To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3 Rotate the focus ring to sharpen the image.
Focus ring
4 Turn the zoom ring to reduce or enlarge the image.
Zoom ring
5 If your image looks likeor, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely. Or press the or buttons on
the projector to correct it.
6 If your image looks likeor, press theorbuttons on the
projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which source to display
Turn projectoron and off
Access projector menus
Turn off projector display and sound
Control projector volume
Navigate projector menus
For more information on using the remote control, see the User’s Guide on
your projector CD.
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11g,
802.11b, or 802.11n wireless network. You must install the optional Epson
wireless LAN module (part number V12H418P12). Your computer must have
a wireless card or built-in wireless interface, and be running Windows 7,
Windows Vista®, Windows XP Professional x64, Windows XP, or Windows 2000,
or Mac OS X 10.3 to 10.6.
1 Turn off the projector and unplug the power cord.
2 Slide the air filter cover latch and open the air filter cover.
3 Remove the screw securing the wireless LAN module stopper, then
remove the stopper.
4 Insert the wireless LAN module into the port.
PowerLite® 95/96W/905/915W/1835
4120194 Rev.0
1-F C
4120194 Rev.0
1-F M
4120194 Rev.0
1-F Y
4120194 Rev.0
1-F K
3 Select Network Configuration and press Enter.
4 Select the Basic menu and press Enter.
5 Select the Projector Name setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the User’s Guide on the projector CD for information on adding
passwords.
6 Select the Wired LAN menu and press Enter.
7 Choose IP Settings and press Enter.
8 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9 To prevent the IP address from appearing on the network standby screen,
set the SSID Display and /or IP Address Display settings to Off.
10 When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software for
Meeting & Presentation to install the program.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is
installed along with your projector User’s Guide.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install links to the download pages from your projector CD, or go to
www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and
select your projector.
5 Replace the wireless LAN module stopper and secure it using the screw
you removed.
6 Close the air filter cover.
7 Plug in and turn on the projector.
8 To configure your projector for your wireless network, do one of
the following:
If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the User’s
Guide on your projector CD.
If you’re not using the key, continue with these steps.
9 Press the Menu button on the remote control, select the Network
menu, and press Enter.
10 Choose Network Configuration and press Enter.
11 Select the Basic menu and press Enter.
12 Select the Projector Name setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the User’s Guide on the projector CD for information on
adding passwords.
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2010 Epson America, Inc. 11/10Printed in XXXXXX CPD-28237
13 Select the Wireless LAN menu and press Enter.
14 Select the Connection Mode setting and choose one of these options:
Quick to connect the projector to one computer on the network
Advanced to connect the projector to multiple computers on
the network
15 If you selected Quick connection mode, select the Channel setting for
your wireless network and turn on the SSID Auto Setting setting.
16 Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
17 If you selected Advanced connection mode, enter your network SSID (up
to 32 characters) as the SSID setting.
18 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
19 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
20 When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
21 Press the Menu button to exit the menu system.
22 See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.
2 Press the Menu button on the remote control, select the Network menu,
and press Enter.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
Make sure the power light on the projector is green and not flashing,
and the A/V Mute slide is open.
Press the Source Search button on the projector or the remote control
to select the computer as the image source.
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as. You may have to hold down the
Fn key while pressing it (such as Fn + F7).
On a Macintosh®, select the Mirror Displays setting in the System
Preferences Displays utility.
Where to get help
Manuals
For more information about using the projector, install the manuals from your
projector CD. View the guides by clicking the icons for them on your computer
desktop.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
US: (562) 276-4394, 6 AM to 8 PM, Pacific Time, Monday through Friday, and
7 AM to 4 PM, Pacific Time, Saturday
Canada: (905) 709-3839, 6 AM to 8 PM, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the User’s Guide on your projector CD.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
4120194 Rev.0
1-B C
4120194 Rev.0
1-B M
4120194 Rev.0
1-B Y
4120194 Rev.0
1-B K
3 Select Network Configuration and press Enter.
4 Select the Basic menu and press Enter.
5 Select the Projector Name setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the User’s Guide on the projector CD for information on adding
passwords.
6 Select the Wired LAN menu and press Enter.
7 Choose IP Settings and press Enter.
8 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9 To prevent the IP address from appearing on the network standby screen,
set the SSID Display and /or IP Address Display settings to Off.
10 When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software for
Meeting & Presentation to install the program.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is
installed along with your projector User’s Guide.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install links to the download pages from your projector CD, or go to
www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and
select your projector.
5 Replace the wireless LAN module stopper and secure it using the screw
you removed.
6 Close the air filter cover.
7 Plug in and turn on the projector.
8 To configure your projector for your wireless network, do one of
the following:
If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the User’s
Guide on your projector CD.
If you’re not using the key, continue with these steps.
9 Press the Menu button on the remote control, select the Network
menu, and press Enter.
10 Choose Network Configuration and press Enter.
11 Select the Basic menu and press Enter.
12 Select the Projector Name setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the User’s Guide on the projector CD for information on
adding passwords.
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2010 Epson America, Inc. 11/10Printed in XXXXXX CPD-28237
13 Select the Wireless LAN menu and press Enter.
14 Select the Connection Mode setting and choose one of these options:
Quick to connect the projector to one computer on the network
Advanced to connect the projector to multiple computers on
the network
15 If you selected Quick connection mode, select the Channel setting for
your wireless network and turn on the SSID Auto Setting setting.
16 Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
17 If you selected Advanced connection mode, enter your network SSID (up
to 32 characters) as the SSID setting.
18 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
19 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
20 When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
21 Press the Menu button to exit the menu system.
22 See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.
2 Press the Menu button on the remote control, select the Network menu,
and press Enter.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
Make sure the power light on the projector is green and not flashing,
and the A/V Mute slide is open.
Press the Source Search button on the projector or the remote control
to select the computer as the image source.
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as. You may have to hold down the
Fn key while pressing it (such as Fn + F7).
On a Macintosh®, select the Mirror Displays setting in the System
Preferences Displays utility.
Where to get help
Manuals
For more information about using the projector, install the manuals from your
projector CD. View the guides by clicking the icons for them on your computer
desktop.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
US: (562) 276-4394, 6 AM to 8 PM, Pacific Time, Monday through Friday, and
7 AM to 4 PM, Pacific Time, Saturday
Canada: (905) 709-3839, 6 AM to 8 PM, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the User’s Guide on your projector CD.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
4120194 Rev.0
1-B C
4120194 Rev.0
1-B M
4120194 Rev.0
1-B Y
4120194 Rev.0
1-B K