Epson Powerlite 8300i Technical Specifications

EPSON PowerLite 8300i Projector
10 - EPSON PowerLite 8300i Projector 5/03
Shutting Down the Projector
When you’ve finished using the projector, follow the 
recommended procedure to shut it down. This extends the life 
of the lamp and protects the projector from possible 
overheating. 
Note: When the projector has not received any input signals for 30 
minutes, it automatically turns off the projector lamp and enters 
sleep mode. This conserves electricity, cools the projector, and 
extends the life of...

EPSON PowerLite 8300i Projector
5/03 EPSON PowerLite 8300i Projector - 11
Note: If the projector does not respond to the remote control, make 
sure batteries are installed and the switch on its side is turned on. 
The projector also might not respond if the batteries are weak; 
you’re standing at too great a distance from the projector; ambient 
light is too bright; a certain type of fluorescent light is present; a 
strong light source (such as direct sunlight) shines into the infrared 
receiver; or...

EPSON PowerLite 8300i Projector
12 - EPSON PowerLite 8300i Projector 5/03
Controlling Multiple Projectors
If you’re using more than one projector, you can control all 
the projectors—or just selected ones—by using the projector 
ID system. To operate a projector, you have to set the remote 
control’s ID to match that of the projector. Or you can 
control all of the projectors simultaneously by setting the 
remote control’s ID to zero. 
Setting the Projector ID
The projector’s default ID is 1. If you need...

EPSON PowerLite 8300i Projector
5/03 EPSON PowerLite 8300i Projector - 13 5. If your network does not assign addresses automatically, 
turn off 
DHCP and enter the projector’s IP Address, 
Subnet Mask, and Gateway Address, as needed. 
Note: To enter numbers using the remote control, press the 
Num button until it lights, then use the number keypad. 
6. After changing an address in the network menu, press the 
Enter button. This stores the value. 
7. When done making all necessary changes, press 
ESC to...

EPSON PowerLite 8300i Projector
14 - EPSON PowerLite 8300i Projector 5/03 Controlling Your Projectors
The control buttons in the upper-right of the EMP Monitor 
screen let you turn on and off the projectors and select video 
sources. (Hold the mouse pointer over a button to see a 
description of its meaning.) Make sure you’ve selected the 
projector(s) you want to operate (with the mouse pointer) 
before clicking one of the buttons. 
Note: To turn on a projector when it’s in standby mode (plugged in 
but...

EPSON PowerLite 8300i Projector
5/03 EPSON PowerLite 8300i Projector - 15 3. EMP NetworkManager connects to the projector, and you 
see this screen: 
4. Verify that the network settings are correct. 
❏Make any desired changes to the projector’s network 
address configuration (turning off DHCP enables the 
manual settings). 
❏You can give the projector a name—up to 15 characters 
long, including the hyphen (-) symbol.
Naming the projector helps you identify it in EMP 
Monitor and EMP NetworkManager. This...

EPSON PowerLite 8300i Projector
16 - EPSON PowerLite 8300i Projector 5/03
Projector Status Lights
s
The lights on top of the projector indicate the projector’s 
status and let you know when a problem occurs.
Key:   = on  = flashing  = off 
Light Description and solution
If no lights are on, make sure the power 
cord is connected securely both at the 
power outlet and the projector. If you have 
just replaced the lamp, make sure the cover 
is securely fastened
.
When the power light is orange, the...

EPSON PowerLite 8300i Projector
5/03 EPSON PowerLite 8300i Projector - 17
Cleaning the Lens 
Clean the lens whenever you notice dirt or dust on the surface. 
❏Use a canister of compressed air to remove dust. 
❏To remove dirt or smears on the lens, use lens-cleaning 
paper. If necessary, moisten a soft cloth with lens cleaner 
and gently wipe the lens surface.
Caution:  Do not use glass cleaner to clean the lens.
Cleaning the Projector 
Before you clean the case, first turn off the projector and 
unplug...

EPSON PowerLite 8300i Projector
18 - EPSON PowerLite 8300i Projector 5/03
Replacing the Lamp
The projection lamp typically lasts for about 3000 hours in 
low-brightness mode, or 2000 hours in high-brightness mode.
Note: The brightness setting can be changed by selecting 
Brightness Control in the projector’s Advanced2 menu.
It is time to replace the lamp when: 
❏The projected image gets darker or starts to deteriorate.
❏The message 
LAMP REPLACE appears on the screen when 
the lamp comes on and the lamp...

EPSON PowerLite 8300i Projector
5/03 EPSON PowerLite 8300i Projector - 19
Optional Accessories
You can purchase these accessories from your dealer, by calling 
EPSON at (800) 873-7766, or by visiting the EPSON Store  
at www.epsonstore.com (U.S. sales only). In Canada, please 
call (800) 463-7766 for dealer referral.
EasyMP.net Option Board
The EasyMP.net option board is also available (part number 
V12H114P01). It offers businesses a premium network 
solution: web browsing, remote desktop client access,...