Epson Powerlite 82c Multimedia Projector Users Guide

							
31
2
Projecting
Once you’ve set up the projector, you’re ready to turn it on, adjust 
the image, and give your presentation. 
Although you can operate the projec tor without it, the remote control 
lets you use additional features.  See Chapter 3 for instructions on 
using the remote. This chapter covers the following:
■Turning on the projector and other equipment
■Adjusting the image
■Adjusting the volume
■Shutting down the projector 
						

							
32Projecting
Turning On Your Equipment
Make sure your projector and other equipment are set up and 
connected correctly, as described in Chapter 1. Then turn on your 
projector, as described below.
If you turn on your connected computer or video equipment before 
starting the projector, the projector automatically detects and displays 
the image source. If you turn on the projector first, or have multiple 
pieces of connected equipment, you may have to select the image 
source manually. See page 34.
Turning On the Projector
Follow these steps to plug in and turn on the projector:
1. Push in the tabs and remove the lens cap.
2. Connect one end of the power cord to the projector’s power inlet. 
3. Connect the other end to an electrical outlet. 
The power light on top of the pr ojector turns orange, indicating 
that the projector is receiving power but not yet turned on. Wait 
until the light stops flashing but stays orange.
caution
Do not use the projector with 
the lens cap in place. The 
heat generated by the lamp 
can damage it. 
						

							
Projecting33
4. Turn on your computer or video source if you have not already. 
5. Press the P 
Power button on top of the projector to turn it on. 
(You can also press the  P 
Power button on the remote control.)
The projector beeps and the power light flashes green as the 
projector warms up. The projector lamp comes on in about 4 
seconds and the power light stays green. 
■If you’re using a computer, you should see your computer 
display projected after a moment or two. If not, you need to 
select the image source. See page 34.
(Windows only: If you see a message saying that it has found 
a plug-and-play monitor, click 
Cancel.) 
■If you’re projecting a video, press the Source Search button 
on the projector or remote control to switch to your video 
source. Then press the 
Play button on your DVD player or 
other device.
■If you are prompted to enter a password, see page 69.
To focus and adjust the image, see page 37. If a projected image fails 
to appear, see “What To Do If You See a Blank Screen” on page 34.
When you’re done with your presentation, shut down the projector as 
described on page 42.
note
If you are using the remote 
control for the first time, be 
sure to insert the batteries as 
described on the  Quick 
Setup poster.
Projector Remote control Power button
warning
Never look into the lens when 
the lamp is on. This can 
damage your eyes, and is 
especially dangerous for 
children. 
						

							
34Projecting
Selecting the Image Source
Selecting the image source lets you switch between images input from 
different pieces of equipment connected to the projector (such as a 
computer and DVD player). If you don’t see the image you want, 
press one of the following buttons on the remote control:
■Comp1
Press this button to move through the following options: 
Computer1 (Auto), Computer 1 (RGB), and Computer 1 
(Component Video)
.
■Comp2
Press this button to move through the following options: 
Computer 2 (Auto), Computer 2 (RGB), Computer 2 
(Component Video)
.
■S-Video
Press to select S-Video.
■Video
Press to select Video.
You can also press the 
Source Search button on the remote control 
or projector until the correct device image is projected. If a projected 
image fails to appear, see the next section for help.
Once you see your image, turn to page 37 for instructions on focusing 
and making other image adjustments. 
What To Do If You See a Blank Screen
If you see a blank screen or a  blue screen with the message No Signal 
after turning on your computer or video source, try the following:
■Make sure the cables are connected correctly, as described in 
Chapter 1.
■Make sure the power light is green and not flashing and the lens 
cap is off. 
■Make sure you’ve selected the correct image source; see the 
previous section. Allow a few seconds for the projector to sync up 
after pressing the button. 
note
The name of the selected 
image source appears in the 
upper right corner of the 
screen. 
						

							
Projecting35
■Check the Signal menu to make sure the correct input source is 
selected. See page 58.
If you’re using a PC laptop:
■Hold down the Fn key and press the function key that lets you 
display on an external monitor. It may have an icon such as   
or it may be labelled 
CRT/LCD. Allow a few seconds for the 
projector to sync up after pressing  it. Check your laptop’s manual 
or online help for details. 
On most systems, the   or 
CRT/LCD key lets you toggle 
between the LCD screen and the projector, or display on both at 
the same time. 
■If you’re projecting from a laptop, and you don’t see the same 
image on the projection screen and computer screen, check your 
monitor settings to make sure both the LCD screen and the 
external monitor port are enabled. 
From the Control Panel, open the 
Display utility. Click the 
Settings tab, then click Advanced. The method for adjusting 
the settings varies by brand; you may need to click a 
Monitor tab, 
then make sure the external Monitor port is set as your primary 
display and/or enabled. See your  computer’s documentation or 
online help for details.  
						

							
36Projecting
If you’re using a Macintosh laptop with OS X:
You may need to set up your system  to display on the projector screen 
as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
System Preferences, then click 
Display or Displays.
2. Select VGA Display or Color LCD, click Arrange or 
Arrangement, and make sure Mirror Displays is checked.
If you’re using a Macint osh laptop with OS 9:
You may need to set up your system  to display on the projector screen 
as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
Control Panels, then click 
Monitors or Monitors and Sound.
2. Click the Arrange icon.
Click here
Select Mirror 
Displays
Click here
Drag one 
monitor icon on 
top of the other 
						

							
Projecting37
3. Drag one monitor icon on top of the other. 
If the 
Arrange option isn’t available, you may need to select one of 
the Simulscan resolution settings:
1. Click the 
Monitor icon, if necessary. 
2. Select a 
Simulscan resolution, as shown. (Allow a few seconds 
for the projector to sync up after making the selection.)
Adjusting the Image
Once you see your image, you’ll need to make certain adjustments:
■To focus or zoom your image, see page 38.
■If the image is too high or too low, you can reposition it. 
See page 38.
■If the image isn’t square, see page 39.
■To adjust image brightness, see page 40.
■If a computer image displays incorrectly, see page 40.
■To change the color mode for your image and surroundings, see 
page 41.
You can make many other adjustments to the image—such as 
changing the brightness, contrast, and aspect ratio—using the 
projector’s menu system. See Chapter 4 for more information.
Click here
Select a 
Simulscan 
resolution 
						

							
38Projecting
Focusing and Zooming Your Image
Rotate the focus ring to sharpen the image.
Rotate the zoom ring to reduce or enlarge the image.
You can also change the image size by moving the projector closer to 
or farther away from the screen. You can use the 
E-Zoom buttons on 
the remote control to zoom in on  a portion of the image. See page 47 
for instructions. 
Adjusting the Height of Your Image
If the image is too low, you can ra ise it by extending the projector’s 
front adjustable foot.
 
1. Stand behind the projector. Press up on the blue foot release  lever and lift the front of the projector to extend the front 
adjustable foot.
Focus ring
Zoom ring
Foot 
						

							
Projecting39
2. Once the image is positioned where you want, release the lever to lock the foot in position.
3. To fine-tune the height of the image,  rotate the foot at the back of the 
projector.
If the image is no longer rectangular after 
raising it, see the next section.
Adjusting the Image Shape
The projector automatically corrects images that are distorted when 
the projector is tilted up or down (up to a 30° tilt). The Keystone 
window appears on the screen while the projector makes the 
correction. If the projected image still isn’t rectangular or has a 
“keystone” shape, do one or more of the following:
■If your image looks like   or  , you’ve placed the projector 
off to one side of the screen, at an angle. Move it directly in front 
of the center of the screen, facing the screen squarely.
■If your image looks like   or  , the Auto Keystone feature 
may have been disabled or you may need to manually adjust the 
keystone correction value. (Auto  Keystone is not available when 
you’re using ceiling or rear proj ection.) Follow the directions 
below:
■To turn on Auto Keystone, press the Menu button on the 
remote control. Use the  pointer button on the remote 
control (or the arrow buttons on the projector) to select the 
Settings menu, then press Enter. If Auto Keystone is OFF, 
use the  pointer button to highlight this option and press 
Enter. Select ON in the Auto Keystone window that appears 
and press 
Enter to save your changes. Exit the menu by 
pressing the
 Menu button. 
Enter button Menu button Pointer button 
						

							
40Projecting
■To manually adjust the keystone correction value, press the  or   buttons on the projector to correct the shape of 
the image. After correction, yo ur image will be slightly 
smaller.
You can also make keystone adjustments using the projector’s Settings 
menu. See page 61.
Adjusting the Brightness
The brightness of an image depends on the source you are projecting 
and the amount of light in the room. If the image is too bright or not 
bright enough, here are two ways you can adjust it:
■Change the Brightness setting in the Image menu. See page 56.
■Select Low or High for the Brightness Control option in the 
Settings menu. (See page 61.) Low brightness mode extends the 
life of the lamp and decreases the fan noise.
Correcting Computer Images
If you’ve connected a computer and the image doesn’t look right, or it 
doesn’t fit properly on the screen, press the 
Auto button on the 
remote control. This automatically resets the projector’s tracking, 
sync, resolution, and position sett ings. You must be projecting a 
computer image for this button to have any effect. Additionally, if the 
Auto Setup option in the Signal menu is set to OFF, the Auto 
function will not work. See page 59.
note
You can also use the buttons 
on the projector to access the 
menu system:
Menu button ESC button
Enter button Arrow buttons