Epson Powerlite 822p Quickstart Manual

							
Quick SetupChoose a location
The projector supports 4 viewing setups. Choose the best one for 
your environment. If you install the projector in a rear or overhead 
position, you’ll need to choose the correct projection option, 
identified below, from the Extended menu. See the User’s Guide 
on your CD-ROM for instructions. 
 
 Table 
  Convenient for temporary front projection.
 
  Choose 
Front from the menu.
 Ceiling 
  Professional installation recommended. 
 
  Choose 
Front /Ceiling from the menu.
 Rear 
   
For installation behind a translucent screen. 
Choose Rear from the menu.
 Rear/Ceiling 
    
Professional installation recommended. 
Choose Rear/Ceiling from the menu.
The distance between the projector and the screen determines  
the size of the image. The diagram below shows approximately  
how big your image will be (diagonally), based on where you set up 
the projector. (For more help determining the size of your image, 
try the Image Size Calculator on the Multimedia Projectors page on 
Epson’s web site.)
2 Connect your video source
Connect the projector to a computer or video source using any of the available 
connections shown below.
 • Check the connectors on your video equipment. If more than one 
    connection is available, choose the one that provides the best quality.
 
    The projector connectors from highest to lowest quality are
 
    Computer (Component Video), S-Video, and Video.
 •   A computer cable is included. You can purchase optional video and 
audio cables through Epson® or an electronics store.  
 •   You can connect up to 4 video devices and use the remote control to 
switch between them. 
	
NOTE		
You	 can	 also	 connect	 an	external	 monitor	to	watch	 the	display	
on	 your	 computer	 monitor	while	watching	 the	projection	 screen	
(when	 the	computer	 cable	is	connected	 to	the	 Computer1	 port).	To	
enhance	 the	sound	 in	your	 presentation,	 you	can	connect	 external	
speakers.	 See	the	
User’s Guide 	on	 your	 CD-ROM	 for	instructions.
3 Set up the remote control
 1  Remove the battery cover.
 2   Insert the batteries. 
 3 Replace the battery cover. 
    The remote control is ready for use.
Turn over
PowerLite
®
 822p/83c
1 Unpack the projector
 You should have the following items:
	
ProjectorPower cord
Computer cable
User’s Guide 
CD-ROM
Password protect 
sticker
Remote control
and batteries
RCA video cable  (composite video)(optional)
S-Video  cable(optional)
Component  video to  VGA cable(optional)
Computer  cable  (included)
L-Audio-R  ports
Audio2 and Audio1 ports 
						

							
Quick SetupChoose a location
The projector supports 4 viewing setups. Choose the best one for 
your environment. If you install the projector in a rear or overhead 
position, you’ll need to choose the correct projection option, 
identified below, from the Extended menu. See the User’s Guide 
on your CD-ROM for instructions. 
 
 Table 
  Convenient for temporary front projection.
 
  Choose 
Front from the menu.
 Ceiling 
  Professional installation recommended. 
 
  Choose 
Front /Ceiling from the menu.
 Rear 
   
For installation behind a translucent screen. 
Choose Rear from the menu.
 Rear/Ceiling 
    
Professional installation recommended. 
Choose Rear/Ceiling from the menu.
The distance between the projector and the screen determines  
the size of the image. The diagram below shows approximately  
how big your image will be (diagonally), based on where you set up 
the projector. (For more help determining the size of your image, 
try the Image Size Calculator on the Multimedia Projectors page on 
Epson’s web site.)
2 Connect your video source
Connect the projector to a computer or video source using any of the available 
connections shown below.
 • Check the connectors on your video equipment. If more than one 
    connection is available, choose the one that provides the best quality.
 
    The projector connectors from highest to lowest quality are
 
    Computer (Component Video), S-Video, and Video.
 •   A computer cable is included. You can purchase optional video and 
audio cables through Epson® or an electronics store.  
 •   You can connect up to 4 video devices and use the remote control to 
switch between them. 
	
NOTE		
You	 can	 also	 connect	 an	external	 monitor	to	watch	 the	display	
on	 your	 computer	 monitor	while	watching	 the	projection	 screen	
(when	 the	computer	 cable	is	connected	 to	the	 Computer1	 port).	To	
enhance	 the	sound	 in	your	 presentation,	 you	can	connect	 external	
speakers.	 See	the	
User’s Guide 	on	 your	 CD-ROM	 for	instructions.
3 Set up the remote control
 1  Remove the battery cover.
 2   Insert the batteries. 
 3 Replace the battery cover. 
    The remote control is ready for use.
Turn over
PowerLite
®
 822p/83c
1 Unpack the projector
 You should have the following items:
	
ProjectorPower cord
Computer cable
User’s Guide 
CD-ROM
Password protect 
sticker
Remote control
and batteries
RCA video cable  (composite video)(optional)
S-Video  cable(optional)
Component  video to  VGA cable(optional)
Computer  cable  (included)
L-Audio-R  ports
Audio2 and Audio1 ports 
						

							Quick SetupChoose a location
The projector supports 4 viewing setups. Choose the best one for 
your environment. If you install the projector in a rear or overhead 
position, you’ll need to choose the correct projection option, 
identified below, from the Extended menu. See the  User’s Guide 
on your CD-ROM for instructions. 
 
 
Table 
  Convenient for temporary front projection.  
  Choose Front
 from the menu.
 
Ceiling 
  Professional installation recommended.   
  Choose Front /Ceiling
 from the menu.
 
Rear 
    For installation behind a translucent screen. 
Choose  Rear from the menu.
 
Rear/Ceiling 
     Professional installation recommended. 
Choose  Rear/Ceiling  from the menu.
The distance between the projector and the screen determines  
the size of the image. The diagram below shows approximately  
how big your image will be (diagonally), based on where you set up 
the projector. (For more help determining the size of your image, 
try the Image Size Calculator on the Multimedia Projectors page on 
Epson’s web site.)
2 Connect your video source
Connect the projector to a computer or video source using any of the available 
connections shown below.
 
•  Check the connectors on your video equipment. If more than one 
    connection is available, choose the one that provides the best quality.  
    The projector connectors from highest to lowest quality are  
    Computer (Component Video), S-Video, and Video.
 
•    A computer cable is included. You can purchase optional video and 
audio cables through Epson
® or an electronics store.  
 
•    You can connect up to 4 video devices and use the remote control to 
switch between them. 
	
NOTE	 	
You 	can 	also 	connect 	an 	external 	monitor 	to 	watch 	the 	display 	
on 	your 	computer 	monitor 	while 	watching 	the 	projection 	screen 	
(when 	the 	computer 	cable 	is 	connected 	to 	the 	Computer1 	port). 	To 	
enhance 	the 	sound 	in 	your 	presentation, 	you 	can 	connect 	external 	
speakers. 	See 	the 	User’s Guide
	on 	your 	CD-ROM 	for 	instructions.
3 Set up the remote control
 1  Remove the battery cover.
 
2    Insert the batteries. 
 
3  Replace the battery cover. 
   
PowerLite
®
 822p/83c
1  Unpack the projector
  You should have the following items:
	
ProjectorPower cord
Computer cable
User’s Guide  
CD-ROMPassword protect  sticker
Remote controland batteries
RCA  video cable  
(composite video) (optional)
S-Video  
cable
(optional) Component  
video to  
VGA cable (optional) Computer  
cable  
(included)
L-Audio-R   ports
Audio2 and Audio1 ports 
						

							
 Where to get help
 Internet support
   Visit Epson’s support website at epson.com/support and select your 
product for solutions to common problems. You can download utilities 
and documentation, get FAQs and troubleshooting advice, or e-mail 
Epson with your questions.
    Visit 
http://www.presentersonline.com to access tips, templates, and 
training for developing successful presentations.
 Speak to a support representative
   To use the Epson PrivateLine® Support service, call (800) 637-7661  
and enter the PIN on the included Epson PrivateLine Support card.  
This service is available 6 
AM to 6 PM, Pacific Time, Monday through 
Friday, for the duration of your warranty period. You may also speak  
with a projector support specialist by dialing one of the following 
numbers. (Toll or long distance charges may apply.)
   U.S.:  (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday-Friday
 Canada:   (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday-Friday 
 Purchase supplies and accessories
    You can purchase screens, carrying cases, and other accessories  
from an Epson authorized reseller. To find the nearest reseller, call  
800-GO-EPSON (800-463-7766). Or you can purchase online at  
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
	
5 Adjust the image
 1    To raise the image, stand behind the 
projector, then press the foot release lever 
and lift the front of the projector. Release 
the lever to lock the foot in the position  
you want. 
 
 2   Rotate the focus ring to sharpen the image, and the zoom ring to 
enlarge or reduce it.
 
 3    If your image looks like  or , first make sure the projector 
is facing the screen squarely. Then, if necessary, press the  or  
buttons on the projector’s control panel until the image is corrected.
 4    To select the best color mode, press the Color Mode button on the 
remote control repeatedly to move through the options.
    See your 
User’s Guide on the CD-ROM for more information about  
image adjustments. 
6  Install your User’s Guide 
and register your projector
 1    Insert the PowerLite Projector CD-ROM in your drive. If the installer 
doesn’t open automatically, double-click the Epson CD-ROM icon, 
then double-click the Epson installer icon. 
 2   Choose your projector, then follow the instructions on the screen  
to register. 
NOTE	 You	 can	also	 register	 at	www.epson.com/webreg.
 3      After you register the projector, click User’s Guide to install it.  
(If you don’t already have Adobe® Reader,® click Adobe Reader  
and follow the on-screen instructions to install it.) 
 4   When you’re done, click Exit. 
    To open your 
User’s Guide, double-click the PL 822p 83c User’s Guide  
icon on your desktop.
4 Plug in and turn on
 1  Open the A/V Mute slide  
    (lens cover).
 2   Connect the power cord 
to the projector and plug 
the other end into an 
electrical outlet.
      The
  Power light on the 
projector turns orange.
 3   Turn on your computer or video source.
 4   Press the Power button on the projector  
or remote control. The projector beeps,  
the Power light flashes green, and the  
projector lamp comes on in about 5 seconds.  
The Power light stays green.
 5   Start your video or presentation. If you have connected more 
than one video source, use the Source Search button on the 
projector or remote control to select the one you want to watch.
NOTE	 	
If	your	 image	 does	not	appear	 on	the	 screen,	 see	the	
Troubleshooting 	section	 for	help.
   Turning off the projector 
 
1    If you’re using a computer, shut it down first, while you can  
still see the display. 
   2  Press the  Power button on the projector or remote control. 
 3    When you see the confirmation message, press the  Power 
button again. The projector beeps twice and the  Power  
light turns orange.
      With Epson’s Instant Off
® technology, there’s no cool-down 
period. When you’re done, just unplug the projector and it’s 
ready to travel.
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on 
your computer or video source, check the following:
   Make sure the Power light on the projector is green and not 
flashing and the A/V Mute slide (lens cover) is open.
   Make sure the cables are connected correctly. (See the User’s Guide 
for more information.)
   If you’ve connected more than one video source, you may need 
to press the Source Search button on the projector or the remote 
control to select the one you want to watch. (Allow a few seconds 
for the projector to sync up after pressing it.)
If the projector and the notebook don’t display the  
same image 
If you’re using a Windows® notebook:
   Hold down the Fn key and press the function key (such as   
or CRT/LCD) that lets you display on an external monitor. On most 
systems, the  or CRT/LCD key lets you toggle between the 
LCD screen and the projector, or display on both at the same time.
    Check your monitor settings to make sure both the LCD screen 
and the external monitor port are enabled. From the Control 
Panel, open the Display utility. Click the Settings tab, then click 
Advanced. The method for adjusting the settings varies by brand; 
you may need to click a Monitor tab, then make sure the external 
Monitor port is set as your primary display and/or enabled. See 
your computer’s documentation or online help for details. 
If you’re using a Macintosh® notebook with OS X:
1   From the Apple® menu, select System Preferences, then click 
Display or Displays.
2   Select VGA Display or Color LCD, click Arrangement or Arrange, 
and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Exceed Your Vision is a trademark of Seiko 
Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is a 
service mark of Epson America, Inc. 
General Notice: Other product names used herein are for identification purposes only and may be 
trademarks of their respective owners. Epson disclaims any and all rights in those marks. 
© 2007  Epson America, Inc. 1/07 
Printed in XXXXXX  CPD-23329
Color Mode 
button
Focus ringZoom ring 
						

							
 Where to get help
 Internet support
   Visit Epson’s support website at epson.com/support and select your 
product for solutions to common problems. You can download utilities 
and documentation, get FAQs and troubleshooting advice, or e-mail 
Epson with your questions.
    Visit 
http://www.presentersonline.com to access tips, templates, and 
training for developing successful presentations.
 Speak to a support representative
   To use the Epson PrivateLine® Support service, call (800) 637-7661  
and enter the PIN on the included Epson PrivateLine Support card.  
This service is available 6 
AM to 6 PM, Pacific Time, Monday through 
Friday, for the duration of your warranty period. You may also speak  
with a projector support specialist by dialing one of the following 
numbers. (Toll or long distance charges may apply.)
   U.S.:  (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday-Friday
 Canada:   (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday-Friday 
 Purchase supplies and accessories
    You can purchase screens, carrying cases, and other accessories  
from an Epson authorized reseller. To find the nearest reseller, call  
800-GO-EPSON (800-463-7766). Or you can purchase online at  
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
	
5 Adjust the image
 1    To raise the image, stand behind the 
projector, then press the foot release lever 
and lift the front of the projector. Release 
the lever to lock the foot in the position  
you want. 
 
 2   Rotate the focus ring to sharpen the image, and the zoom ring to 
enlarge or reduce it.
 
 3    If your image looks like  or , first make sure the projector 
is facing the screen squarely. Then, if necessary, press the  or  
buttons on the projector’s control panel until the image is corrected.
 4    To select the best color mode, press the Color Mode button on the 
remote control repeatedly to move through the options.
    See your 
User’s Guide on the CD-ROM for more information about  
image adjustments. 
6  Install your User’s Guide 
and register your projector
 1    Insert the PowerLite Projector CD-ROM in your drive. If the installer 
doesn’t open automatically, double-click the Epson CD-ROM icon, 
then double-click the Epson installer icon. 
 2   Choose your projector, then follow the instructions on the screen  
to register. 
NOTE	 You	 can	also	 register	 at	www.epson.com/webreg.
 3      After you register the projector, click User’s Guide to install it.  
(If you don’t already have Adobe® Reader,® click Adobe Reader  
and follow the on-screen instructions to install it.) 
 4   When you’re done, click Exit. 
    To open your 
User’s Guide, double-click the PL 822p 83c User’s Guide  
icon on your desktop.
4 Plug in and turn on
 1  Open the A/V Mute slide  
    (lens cover).
 2   Connect the power cord 
to the projector and plug 
the other end into an 
electrical outlet.
      The
  Power light on the 
projector turns orange.
 3   Turn on your computer or video source.
 4   Press the Power button on the projector  
or remote control. The projector beeps,  
the Power light flashes green, and the  
projector lamp comes on in about 5 seconds.  
The Power light stays green.
 5   Start your video or presentation. If you have connected more 
than one video source, use the Source Search button on the 
projector or remote control to select the one you want to watch.
NOTE	 	
If	your	 image	 does	not	appear	 on	the	 screen,	 see	the	
Troubleshooting 	section	 for	help.
   Turning off the projector 
 
1    If you’re using a computer, shut it down first, while you can  
still see the display. 
   2  Press the  Power button on the projector or remote control. 
 3    When you see the confirmation message, press the  Power 
button again. The projector beeps twice and the  Power  
light turns orange.
      With Epson’s Instant Off
® technology, there’s no cool-down 
period. When you’re done, just unplug the projector and it’s 
ready to travel.
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on 
your computer or video source, check the following:
   Make sure the Power light on the projector is green and not 
flashing and the A/V Mute slide (lens cover) is open.
   Make sure the cables are connected correctly. (See the User’s Guide 
for more information.)
   If you’ve connected more than one video source, you may need 
to press the Source Search button on the projector or the remote 
control to select the one you want to watch. (Allow a few seconds 
for the projector to sync up after pressing it.)
If the projector and the notebook don’t display the  
same image 
If you’re using a Windows® notebook:
   Hold down the Fn key and press the function key (such as   
or CRT/LCD) that lets you display on an external monitor. On most 
systems, the  or CRT/LCD key lets you toggle between the 
LCD screen and the projector, or display on both at the same time.
    Check your monitor settings to make sure both the LCD screen 
and the external monitor port are enabled. From the Control 
Panel, open the Display utility. Click the Settings tab, then click 
Advanced. The method for adjusting the settings varies by brand; 
you may need to click a Monitor tab, then make sure the external 
Monitor port is set as your primary display and/or enabled. See 
your computer’s documentation or online help for details. 
If you’re using a Macintosh® notebook with OS X:
1   From the Apple® menu, select System Preferences, then click 
Display or Displays.
2   Select VGA Display or Color LCD, click Arrangement or Arrange, 
and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Exceed Your Vision is a trademark of Seiko 
Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is a 
service mark of Epson America, Inc. 
General Notice: Other product names used herein are for identification purposes only and may be 
trademarks of their respective owners. Epson disclaims any and all rights in those marks. 
© 2007  Epson America, Inc. 1/07 
Printed in XXXXXX  CPD-23329
Color Mode 
button
Focus ringZoom ring 
						

							
 Where to get help
 Internet support
   Visit Epson’s support website at epson.com/support and select your 
product for solutions to common problems. You can download utilities 
and documentation, get FAQs and troubleshooting advice, or e-mail 
Epson with your questions.
    Visit 
http://www.presentersonline.com to access tips, templates, and 
training for developing successful presentations.
 Speak to a support representative
   To use the Epson PrivateLine® Support service, call (800) 637-7661  
and enter the PIN on the included Epson PrivateLine Support card.  
This service is available 6 
AM to 6 PM, Pacific Time, Monday through 
Friday, for the duration of your warranty period. You may also speak  
with a projector support specialist by dialing one of the following 
numbers. (Toll or long distance charges may apply.)
   U.S.:  (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday-Friday
 Canada:   (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday-Friday 
 Purchase supplies and accessories
    You can purchase screens, carrying cases, and other accessories  
from an Epson authorized reseller. To find the nearest reseller, call  
800-GO-EPSON (800-463-7766). Or you can purchase online at  
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
	
5 Adjust the image
 1    To raise the image, stand behind the 
projector, then press the foot release lever 
and lift the front of the projector. Release 
the lever to lock the foot in the position  
you want. 
 
 2   Rotate the focus ring to sharpen the image, and the zoom ring to 
enlarge or reduce it.
 
 3    If your image looks like  or , first make sure the projector 
is facing the screen squarely. Then, if necessary, press the  or  
buttons on the projector’s control panel until the image is corrected.
 4    To select the best color mode, press the Color Mode button on the 
remote control repeatedly to move through the options.
    See your 
User’s Guide on the CD-ROM for more information about  
image adjustments. 
6  Install your User’s Guide 
and register your projector
 1    Insert the PowerLite Projector CD-ROM in your drive. If the installer 
doesn’t open automatically, double-click the Epson CD-ROM icon, 
then double-click the Epson installer icon. 
 2   Choose your projector, then follow the instructions on the screen  
to register. 
NOTE	 You	 can	also	 register	 at	www.epson.com/webreg.
 3      After you register the projector, click User’s Guide to install it.  
(If you don’t already have Adobe® Reader,® click Adobe Reader  
and follow the on-screen instructions to install it.) 
 4   When you’re done, click Exit. 
    To open your 
User’s Guide, double-click the PL 822p 83c User’s Guide  
icon on your desktop.
4 Plug in and turn on
 1  Open the A/V Mute slide  
    (lens cover).
 2   Connect the power cord 
to the projector and plug 
the other end into an 
electrical outlet.
      The
  Power light on the 
projector turns orange.
 3   Turn on your computer or video source.
 4   Press the Power button on the projector  
or remote control. The projector beeps,  
the Power light flashes green, and the  
projector lamp comes on in about 5 seconds.  
The Power light stays green.
 5   Start your video or presentation. If you have connected more 
than one video source, use the Source Search button on the 
projector or remote control to select the one you want to watch.
NOTE	 	
If	your	 image	 does	not	appear	 on	the	 screen,	 see	the	
Troubleshooting 	section	 for	help.
   Turning off the projector 
 
1    If you’re using a computer, shut it down first, while you can  
still see the display. 
   2  Press the  Power button on the projector or remote control. 
 3    When you see the confirmation message, press the  Power 
button again. The projector beeps twice and the  Power  
light turns orange.
      With Epson’s Instant Off
® technology, there’s no cool-down 
period. When you’re done, just unplug the projector and it’s 
ready to travel.
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on 
your computer or video source, check the following:
   Make sure the Power light on the projector is green and not 
flashing and the A/V Mute slide (lens cover) is open.
   Make sure the cables are connected correctly. (See the User’s Guide 
for more information.)
   If you’ve connected more than one video source, you may need 
to press the Source Search button on the projector or the remote 
control to select the one you want to watch. (Allow a few seconds 
for the projector to sync up after pressing it.)
If the projector and the notebook don’t display the  
same image 
If you’re using a Windows® notebook:
   Hold down the Fn key and press the function key (such as   
or CRT/LCD) that lets you display on an external monitor. On most 
systems, the  or CRT/LCD key lets you toggle between the 
LCD screen and the projector, or display on both at the same time.
    Check your monitor settings to make sure both the LCD screen 
and the external monitor port are enabled. From the Control 
Panel, open the Display utility. Click the Settings tab, then click 
Advanced. The method for adjusting the settings varies by brand; 
you may need to click a Monitor tab, then make sure the external 
Monitor port is set as your primary display and/or enabled. See 
your computer’s documentation or online help for details. 
If you’re using a Macintosh® notebook with OS X:
1   From the Apple® menu, select System Preferences, then click 
Display or Displays.
2   Select VGA Display or Color LCD, click Arrangement or Arrange, 
and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Exceed Your Vision is a trademark of Seiko 
Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is a 
service mark of Epson America, Inc. 
General Notice: Other product names used herein are for identification purposes only and may be 
trademarks of their respective owners. Epson disclaims any and all rights in those marks. 
© 2007  Epson America, Inc. 1/07 
Printed in XXXXXX  CPD-23329
Color Mode 
button
Focus ringZoom ring