Epson Powerlite 822p Multimedia Projector Users Guide

							Monitoring the Projector Over a Network91
Connecting to the Network
Follow these steps to connect the projector to your network and 
configure it with an IP address. 
1. Connect the projector to your network using a commercially 
available 100BaseTX or 10BaseT network cable. Connect the 
cable to the 
LAN port on the projector. 
2. Press the projector’s P
Power button to turn it on. 
						

							92Monitoring the Projector Over a Network
Selecting Network Settings
Follow the instructions in this section to set up the projector’s 
network settings in the menu system.
1. Press the 
Menu button.
2. Select the 
Network menu. 
3. Press 
Enter. Then use the up and down arrow buttons and the 
Enter button to set the following options:
■Wired LAN
If your network assigns addresses automatically, turn on the 
DHCP setting.
If your network does not assign addresses automatically, turn 
off 
DHCP and enter the projector’s IP Address, Subnet 
Mask
, and Gateway Address as needed. 
To enter numbers, use the numeric buttons on the remote 
control.
■PJLink Password
Lets you enter a password for using the PJLink™ protocol to 
control the projector. 
■Web Control Password
Lets you enter a password for accessing the projector over the 
web from a computer running the EMP Monitor software. 
						

							Monitoring the Projector Over a Network93
■SNMP
If you’re a network administrator, you can use the SNMP 
option to enter a trap IP address. This lets you receive trap 
alerts for the projector on a computer running the SNMP 
Manager software.
■Mail
When enabled, the projector sends you an e-mail alert if it has 
any problems. For instructions on setting up e-mail alerts, see 
the next section.
■Projector Name
Enter a name for identifying the projector over the network.
Using Projector E-mail Alerts
When this feature is enabled, the projector sends you an e-mail alert if 
it has any problems. 
1. Press the 
Menu button, select the Network menu, and press 
Enter. 
2. Select 
Mail and press Enter.
3. Select the following settings as necessary:
■Mail Notification
Select On to enable sending of an e-mail if there is a problem 
with the projector.
■SMTP Server
Enter the IP address for the SMTP server for the projector. 
You can enter a number from 0 to 255 in each field of the 
address.
■Port Number
Enter the SMTP server’s port number. The default value is 
25. You can enter a numeric value from 1 to 65535.
■Destination Address 1/2/3
Choose one of the Destination Address fields, then enter 
the e-mail address where you want to receive a message when 
a problem occurs.
note
You can also set e-mail alerts 
from EMP Monitor (see 
page 98).
note
If a critical problem develops 
with a projector which 
causes it to suddenly stop 
working, it may not be 
possible for the projector to 
send a message.
If Standby Mode is set to 
Network On in the 
Extended menu, the 
projector can still be 
monitored even if the 
projector is in standby mode 
(when the power is off). 
						

							94Monitoring the Projector Over a Network4. When you’re done, press 
Menu to exit the menu system. 
When a problem occurs, an e-mail message is sent to the specified 
addresses with the subject line 
EPSON Projector and the following 
information:
■Line 1: The name of the projector where the problem has 
occurred
■Line 2: The IP address of the projector where the problem has 
occurred
■Line 3: Details of the problem 
Using EMP Monitor
EMP Monitor lets you use a remote computer to manage your 
projectors. It lets you easily turn the projector on or off, switch image 
sources, and check its status. 
Before using EMP Monitor, make sure you’ve installed the software 
(available for Windows only) as described on page 90. The computer 
you’re using to monitor the projector should already be connected to 
your network.
Opening and Closing EMP Monitor
To start EMP Monitor, click Start > Programs or All Programs > 
EPSON Projector > EMP Monitor
. 
If you’ve added the program to the Startup programs folder, then it 
may already be open. If so, click the icon in the system tray on the 
lower-right corner of your screen to display the EMP Monitor 
window:
To close EMP Monitor, select 
Exit from the File menu or right-click 
the program icon shown above, then select 
Exit.
note
If you want to monitor the 
projector while it is in 
standby mode, select 
Standby Mode in the 
Extended menu, then 
select 
Network On. 
See page 58.
Click here to start EMP Monitor 
						

							Monitoring the Projector Over a Network95
Registering a Projector
Before you can monitor a projector, you have to register it. Follow 
these steps to automatically search for your projector. 
1. Open EMP Monitor.
2. Select 
Edit > New > Projector (automatic search). 
3. Click 
Search to locate projectors currently operating on the 
network.
4. Select the projector you want to add by clicking its name, then 
click the 
Edit button. 
5. Enter a Display name, select a Parent group, if necessary, enter a 
Monitor Password, if necessary, and a Description for the 
projector. 
6. Click the 
Register button.
7. Repeat steps 2 through 5 to register any additional projectors on 
the network.
8. When you’re done adding the projector, click 
Cancel. You see a 
screen with a list of all registered projectors:
Monitoring Your Projector
The EMP Monitor screen lets you monitor your projector status and 
check if a problem has occurred. 
For the most current status, click the 
Refresh button. 
The following table describes the EMP Monitor status icons. 
Group status icons
No warnings or problems in the projector group.
Warning or problem in a projector in the group.
Monitoring disabled. Right click the icon and select 
Monitoring Enabled to begin monitoring the group.
Data is currently being updated.
note
If the projector is not 
automatically found, your 
projector may not be 
connected or configured 
correctly for the network. See 
page 91.
To delete a projector from 
the list, right-click the 
projector name, and click 
Delete.
note
To monitor a projector 
when it’s in standby mode 
(plugged in but not turned 
on), you must select 
Network On as the 
Standby Mode setting in 
the projector’s Extended 
menu (see page 58).
For detailed status 
information, right-click the 
projector and click 
Property. 
						

							96Monitoring the Projector Over a Network
Type status icons
No warnings or problems. 
Warning or problem.
Monitor Password error. No monitor password was 
entered when you registered the projector, or an 
incorrect password was entered.
Monitoring disabled. Right-click the icon and select 
Monitoring Enabled to monitor the projector.
Data is currently being updated.
Network error (projector is not connected to the 
network, the power cable is disconnected, or 
Network Off is selected as the Standby Mode 
setting in the Extended menu; see page 58).
Network error (Esc/VP.net communication error).
Power status icons
The projector is powered on; normal status.
The projector is powered off; normal status.
The projector is powered on; abnormal status.
The projector is powered off; abnormal status.
Temperature level status icons
The projector’s internal temperature is normal (low).
The projector’s internal temperature is normal 
(medium).
The projector’s internal temperature is normal (high).
The projector’s internal temperature is high 
(high-temperature warning).
The projector’s internal temperature is too high 
(high-temperature error). The projector is turned off 
automatically. 
						

							Monitoring the Projector Over a Network97
Error status icons
Lamp life warning. The lamp is nearing the end of its 
life.
High-temperature warning. The projector is getting 
too hot but continues to operate.
Replace air filter.
No air filter. The air filter is not installed or installed 
incorrectly.
Low air flow. The air filter needs to be cleaned or 
replaced.
Air flow sensor error. Contact Epson as described on 
page 87.
Lamp cover door open. Close the lamp cover door.
Lamp out. The lamp has reached the end of its life.
Lamp failure at power on. The lamp has reached its 
end of life or is installed incorrectly.
High internal temperature error. The projector is 
turned off automatically.
Internal (system) error. Contact Epson as described 
on page 87.
Fan error. Contact Epson as described on . 
Sensor error. Contact Epson as described on 
page 87.
Other error. Contact Epson as described on page 87. 
						

							98Monitoring the Projector Over a Network
Using E-mail Alerts
You can set up e-mail alerts to warn you of problems with the 
projector. 
1. Open EMP Monitor.
2. From the Tool menu, select 
Mail notification function.
3. Turn the Mail notification function setting 
On.
4. Enter the IP address and port number of your network’s SMTP 
(outgoing) mail server.
5. Enter the Sender (projector) mail address.
6. Enter up to three e-mail addresses to send alerts to in the 
Recipient mail address boxes.
7. Click the 
Notification event buttons to select the conditions 
under which an e-mail alert will be sent.
8. When you’re done, click the 
OK button.
If a projector experiences a problem, EMP Monitor sends an e-mail 
message to each of the addresses you entered in the Set mail 
notification function window. The subject line and body of the 
message includes the projector’s name and the warning or error 
(similar to the those listed on page 95).
When the problem has been fixed, EMP Monitor sends a message 
indicating the problem has been resolved.
note
You can also set e-mail alerts 
from the projector’s menu 
system (see page 93).
note
If a projector develops a 
critical problem, it may not 
be possible for it to report the 
error. 
						

							Monitoring the Projector Over a Network99
Using a Browser to Monitor the 
Projector
If your projector is connected to a network, you can use a standard 
web browser to monitor and control it. When using a browser to 
access the projector, you cannot connect through a proxy server.
1. Make sure that the projector is connected to your network, as 
described on page 91. 
2. Follow the instructions on page 58 to set 
Standby Mode to 
Network On in the Extended menu so you can monitor the 
projector in standby mode. 
3. Open your web browser and enter the IP address of the projector 
you want to monitor in the browser window.
If you’re not sure what the address of the projector is, turn the 
projector on and select 
Wired LAN from the Network menu to 
display the IP address of the projector. See page 92.
You see a login screen.
4. Do one of the following:
■If you didn’t set a Web Control Password in the Network 
menu, click 
OK.
■If you set a Web Control password in the Network menu, 
enter it in the 
Password box, then click OK.
You see a screen displaying the settings you can change.
5. Select one of the menu options, then change any settings as 
needed. These settings correspond to those found in the 
projector’s menu system. See page 50 for details.
You cannot change the 
User’s Logo, High Altitude Mode, and 
Language settings in the Extended menu or select the Reset All and 
Reset Lamp Hours in the Reset menu
Use the controls at the bottom of the screen to choose a source, stop 
the action, turn off the picture and sound, or turn the projector’s 
power on or off. 
						

							100Monitoring the Projector Over a Network