Epson Powerlite 810p Multimedia Projector Users Guide

Setting Up the Projector15
Connecting to Video Sources
You can connect a DVD player, VCR, camcorder, laser disc player, 
digital camera, or any other compatible video source to your projector.
The projector supports HDTV, NTSC, PAL, and SECAM, and 
automatically detects the video format. 
The projector can receive composite video, S-Video, and component 
video. You can connect one or more of these video sources at the same 
time. 
The type of cable you use depends on whether you have composite 
video,...

16Setting Up the Projector
Connecting the RCA A/V Cable
Before starting, make sure the projector and your DVD player or 
other video source are turned off.
1. Connect the yellow plug on one end of the A/V cable to the 
projector’s yellow 
Video jack. 
2. Connect the other yellow plug to the video-out jack on your video 
source.
3. Connect the red and white plugs on the A/V cable to the 
projector’s 
Audio L (white) and R (red) jacks.
4. Connect the red and white plugs on the other end of the cable to...

Setting Up the Projector17
Connecting an S-Video Cable
If your video source has an S-Video jack, you can use it to project a 
higher quality video image. However, you’ll need an S-Video cable, 
which may be included with your video source, or can be purchased 
separately.
Before starting, make sure the projector and your DVD player or 
other video source are turned off.
1. Insert one end of an S-Video cable into the projector’s 
S-Video 
connector. 
2. Insert the other end into the S-Video output port of...

18Setting Up the Projector
Connecting a Component Video Cable
If your video source has component (blue, green, and red) connectors, 
you can use them to project a higher quality video image. However, 
you’ll need a VGA-to-component video cable, which is available from 
EPSON; see page 8.
Before starting, make sure the projector and your DVD player or 
other video device are turned off.
1. Connect the VGA end of the cable to the projector’s 
Computer 2/Component Video port. 
2. Connect the red, green, and...

2
Using the Projector19
Using the Projector
Once you’ve connected the projector to your computer or other 
equipment (as described in Chapter 1 or Appendix A), you’re ready to 
turn on the projector, adjust the image, and give your presentation. 
Although you can operate the projector without it, the remote control 
lets you use additional features. See Chapter 3 for instructions on 
using the remote. This chapter covers the following:

Turning on the projector and other equipment

Adjusting the image...

20Using the Projector
Turning On Your Equipment
Make sure your projector and other equipment are set up and 
connected correctly, as described in Chapter 1 or Appendix A. Then 
turn on your projector, as described below, followed by any 
equipment you’ve connected to it. You can turn on your computer 
and video equipment in any order, but if you have more than one 
computer or video source connected, you may have to switch to the 
desired source as described on page 28. 
Turning On the Projector
Follow...

Using the Projector21
5. Press the red Power button on top of the projector. 
The power light flashes green as the projector warms up, and the 
projection lamp comes on in about 30 seconds. The power light 
stays green, and you may see a blue screen with the 
No Signal 
message displayed. This is normal.
6. Do one of the following:

If you’re projecting from a computer, turn on or restart your 
computer. In a few moments, you should see your computer 
display projected.
If you see a New Hardware Wizard...

22Using the Projector
What To Do If You See a Blank Screen 
If you see a blank screen or a blue screen with the No Signal message 
after turning on your computer or video source, try the following:

Make sure the cables are connected correctly, as described on 
page 12 (for laptops) or in Appendix A (for other systems).

Make sure the power light is green and not flashing and the lens 
cover is off. 

Try restarting your computer.

If you’ve conne cte d more t han one  computer and/or video source, 
you...

Using the Projector23
If the Arrange option isn’t available, you may need to select one of the 
Simulscan resolution settings:
1. Click the 
Monitor icon. 
2. Select a 
Simulscan resolution as shown. (Allow a few seconds for 
the projector to sync up after making the selection.)
If you’re using a PC laptop:

Press the function key that lets you display on an external 
monitor. It’s often labelled with an icon such as   but it may 
also be labelled 
CRT/LCD. You may have to hold down the Fn key 
while...

24Using the Projector
Adjusting the Image
Once you see your image, you’ll need to make certain adjustments:    

To focus or zoom your image, see below. 

If the image is too high or too low, you can reposition it. See 
page 25.

If the image isn’t square, see page 26.

If only part of a computer image is displayed, you may need to 
press the 
Resize button. See page 27 for more information.

If the projected image is flickering or “noisy,” see page 27. 
Focusing and Zooming Your Image
Rotate the focus...