Epson Powerlite 800p Technical Specifications

							EPSON PowerLite 600p/800p/810p Projectors
8/01 EPSON PowerLite 600p/800p/810p Projectors - 1
Projector Specifications 
General
Type of display Poly-silicon Thin Film Transistor(TFT),
active matrix
Size of LCD panels    Diagonal: 0.9 inches (22.9 mm) 
Lens F=1.74 to 2.06, f=28.3 to 37.98 mm
Resolution 
(native format) 1024
 × 768 pixels (800p and 810p)
800 
× 600 (600p)
Color reproduction 24 bit, 16.7 million colors
Brightness 2000 lumens (ANSI) (810p)
1500 lumens (ANSI) (800p)
1700 lumens (ANSI) (600p)
Contrast ratio 400 : 1 
Image size 30 to 300 inches
Projection distance 2.85 to 40.7 feet (0.87 to 12.4 meters)
Projection methods Front, rear, upside-down (ceiling mount)
Internal speaker
system 5 W monaural
Optical aspect ratio 4 : 3 (horizontal : vertical)
Zoom ratio 1 : 135
Noise level 38 dB
Keystone 
correction angle Vertical: ± 30° maximum
Horizontal: ± 10° maximum
Projection Lamp
Type UHE (Ultra High Efficiency)
Power 
consumption 200 W
Lamp life About 1500 hours
Part number ELPLP15
Remote Control
Range 32.8 feet (10 meters)
Batteries Alkaline AA (2)
Mouse Compatibility
Supports PS/2 and USB 
Remote IR Receiver
Supports EPSON Remote IR Receiver (typically used for rear 
screen projection)
foot release 
button contro
l panel
zoom ring
focus ring
remote control 
receiver
Kensington lock 
port
lamp cover latch
A/C power inlet
remote control receiverstatus lights
handle
speaker
back 
adjustable 
foot
Computer1 (DVI)
optional 
remote 
receiver S-Video Serial Computer2/ 
Component 
Video Audio Out
Mouse 
Audio1 Monitor 
Out  USB in USB out
Composite 
VideoAudio2 
						

							EPSON PowerLite 600p/800p/810p Projectors
2 - EPSON PowerLite 600p/800p/810p Projectors 8/01 Dimensions
Height 4.1 inches (104 mm)
Width 13.7 inches (348 mm)
Depth 10.8 inches (274 mm)
Weight 9.3 lb (4.2 kg)
Electrical
Rated frequency 50 to 60 Hz
Power supply 100 to 120 VAC, 3.1 A
200 to 240 VAC, 1.5 A
Power 
consumption Operating: 280 W
Standby: 5.5 W
Environmental
Temperature Operating: 41 to 95 °F (5 to 35 °C),
Storage: 14 to 140 °F (–10 to 60 °C),
Humidity Operating: 20 to 80% RH, 
non-condensing
Storage: 10 to 90% RH, 
non-condensing
Safety
United States FCC Part 15B Class B
UL1950 Rev. 3
Canada DOC ICES003 Class B
CSA C22.2 No. 950 Rev. 2
CE Marking Directive 89/336/EEC, 73/23/EEC
EN 55022, EN 55024, EN 60950
Compatible Video Formats
The projector supports the following video standards: NTSC, 
HDTV, PAL, and SECAM, as well as the monitor display 
formats listed below.
To project images output from a computer, the computer’s 
video card must be set at a refresh rate (vertical frequency) 
that’s compatible with the projector; see the following table 
for compatible formats. Some images are automatically resized 
to display in the projector’s native format. The frequencies of 
some computers may not allow images to display correctly; see 
your computer’s documentation for details.
.
ModeRefresh 
rate (Hz) ResolutionDVI 
support
PC98 57 640 × 400 supported
VGAEGA 70 640 
× 350 supported
VGA60 60 640 
× 480 supported
VESA72 72 640 
× 480 supported
VESA75 75 640 
× 480 supported
VESA85 85 640 
× 480 supported
VGA120 120 640 
× 480
SVGA56 56 800 
× 600 supported
SVGA60 60 800 
× 600 supported
SVGA72 72 800 
× 600 supported
SVGA75 75 800 
× 600 supported
SVGA85 85 800 
× 600 supported
SVGA120 120 800 
× 600
XGA43i 43 1024 
× 7681
XGA60 60 1024 × 7681supported
XGA70 70 1024 
× 7681supported
XGA75 75 1024 
× 7681supported
XGA85 85 1024 
× 7681supported
XGA120 120 1024 
× 7681
SXGA1—70 70 1152 × 8642supported
SXGA1—75 75 1152 
× 8642supported
SXGA1—85 85 1152 
× 8642supported
SXGA1—100 100 1152 
× 8642
SXGA2—60 60 1280 × 9602supported
SXGA2—75 75 1280 
× 9602supported
SXGA2—85 85 1280 
× 9602
SXGA3—43i 43 1280 × 10242
SXGA3—60 60 1280 × 10242supported
SXGA3—75 75 1280 
× 10242supported
SXGA3—85 85 1280 
× 10242
SXGA+60 60 1400 × 10502supported
SXGA+75 75 1400 
× 10502supported
SXGA+85 85 1400 
× 10502supported
UXGA48i 48 1600 
× 12002,3
UXGA60 60 1600 × 12002,3
UXGA65 65 1600 × 12002,3
UXGA70 70 1600 × 12002,3
UXGA75 75 1600 × 12002,3
UXGA80 80 1600 × 12002,3
UXGA85 85 1600 × 12002,3
iMAC VGA 117 640 × 480
iMAC SVGA 95 800 
× 600
iMAC XGA 75 1024 
× 7681supported
MAC II 13 67 640 
× 480 supported
MAC16 75 832 
× 624 supported
MAC19 75 1024 
× 7681supported
MAC21 75 1152 
× 8702supported
TV525i 602
TV625i 502
SDTV525p 602supported
HDTV750p 602supported
HDTV1125i 602 
						

							EPSON PowerLite 600p/800p/810p Projectors
8/01 EPSON PowerLite 600p/800p/810p Projectors - 3
1The image is resized so that it displays using one of the projector’s 
native formats (PowerLite 600p only).
2The image is resized so that it displays using one of the projector’s 
native formats. 
3Not supported on the PowerLite 600p
Computer Video Port Pin Assignments
The Computer 2/Component Video port is a female video 
RGB, 15-pin micro-D-style connector. Here are the pin 
assignments: 
ELP Link Lite
If you want to be able to control the projector’s settings from a 
computer, you can install the ELP Link Lite program. You can 
download this program, plus its User’s Guide, from EPSON’s 
web site at support.epson.com. You’ll also need a serial or 
USB cable to connect the projector to the computer.
Positioning the Projector
Follow these guidelines to get the best results when projecting:
❏Place the projector on a sturdy, level surface, between 
2.85 and 41 feet from the screen.
❏Make sure there is plenty of space for ventilation around and 
under the projector.
❏Make sure the projector is within 10 feet of a grounded 
electrical outlet or extension cord and within 5 feet of the 
image source.
❏Face the projector squarely toward the screen. 
Note: It’s easier to position the projector when the screen is 
directly in front of the room. However, if you need to place it off-
center, you can use the keystone correction feature to maintain a 
square image. 
If you place the projector below the level of the screen, you’ll 
have to tilt it up by extending the foot as shown. Tilting the 
projector upward causes the image to lose its square shape, but 
you can correct the distortion by pressing the 
Keystone 
button as described on page 6. 
If you place the projector level with the bottom of the screen, 
the image will be square and you won’t have to adjust it. If 
you place the projector higher than the bottom of the screen, 
the image will still be square, but you won’t be able to fill the 
whole screen with the image.
NTSC 602
NTSC4.43 602
PAL 502
M-PAL 602
N-PAL 502
PAL60 602
SECAM 502
Pin #Computer 2/Component 
Video port (analog)
1 Red video
2 Green video
3 Blue video
4GND
5GND
6 Red video GND
7 Green video GND
8 Blue video GND
9 Reserved
10 Synchronous GND
11 GND
12 SDA
13 Horizontal sync/composite sync
14 Vertical sync
15 SCL
ModeRefresh 
rate (Hz) ResolutionDVI 
support
ideal 
height 
						

							EPSON PowerLite 600p/800p/810p Projectors
4 - EPSON PowerLite 600p/800p/810p Projectors 8/01 The projector can be installed for four different viewing 
setups: front projection, ceiling mounting, rear projection 
onto a semi-transparent screen, or rear/ceiling projection, as 
shown: 
To project from overhead, you’ll need to select 
Ceiling in the 
projector’s Advanced menu. To project from the rear, select 
Rear Proj. 
If you’re ceiling-mounting the projector and you place it 
above screen level, you’ll have to tilt it down to position the 
image on-screen. This causes the image to lose its square 
shape. You can then correct the distortion by using the 
V Keystone function in the projector’s menu system or by 
using the 
Keystone buttons on the projector’s control panel.Image Size and Projection Distance
Use the tables below to estimate how far to place the projector 
from the screen. Since the size of the image can be changed by 
rotating the zoom ring, a range of distance is given for each 
screen size. 
Note that if you tilt the projector upward by extending the 
foot or use electronic keystone correction, your image size may 
vary.
Displaying an Image
Once the projector is connected to your computer or video 
source and plugged in, press the red 
Power button on top of 
the projector to turn it on. The power light flashes green as the 
projector warms up, and the projection lamp comes on in 
about 30 seconds. The power light stays green, and you may 
see a blue screen with the message 
No Signal displayed. This is 
normal. 
Do one of the following:
❏Turn on or restart your computer. In a few moments, you 
should see your computer display projected.
If you see a New Hardware Wizard message saying that it has 
found a plug-and-play monitor, click 
Cancel. If you see a 
New Hardware Wizard message about USB audio, click 
Next and follow the instructions on the screen (Windows 
only).
❏If you’re projecting a video, press the 
Play button on your 
video source.
If a projected image fails to appear, see the next section for 
help. 
front projection
ceiling mounting
rear projection
rear/ceiling projectionDiagonal screen 
size Distance
30 inches 2.9 to 3.9 feet (0.87 to 1.20 meters)
60 inches 5.9 to 8 feet (1.80 to 2.45 meters)
100 inches 9.9 to 13.6 feet (3.02 to 4.13 meters)
200 inches 20 to 27.2 feet (6.10 to 8.30 meters)
300 inches 30.1 to 40.9 feet (9.17 to 12.48 meters) 
						

							EPSON PowerLite 600p/800p/810p Projectors
8/01 EPSON PowerLite 600p/800p/810p Projectors - 5 What To Do If You See a Blank Screen
If you see a blank screen or a blue screen with the message 
No Signal after turning on your computer or video source, do 
one of the following:
❏Make sure the cables are connected correctly, as described in 
the User’s Guide.
❏Make sure the power light is green and not flashing and the 
lens cover is off. 
❏Try restarting your computer.
❏If you’ve connected more than one computer and/or video 
source, you may need to press the 
Computer/YCbCr or 
Video button on top of the projector to select the correct 
source. Allow a few seconds for the projector to sync up after 
pressing the button.
If you’re using a PowerBook:
You may need to set up your system to display on the 
projector screen as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
Control Panels, then click 
Monitors or Monitors and Sound.
2. Click the 
Arrange icon and drag one monitor icon on top of 
the other. If the Arrange option isn’t available, you may need to select 
one of the Simulscan resolution settings:
1. Click the 
Monitor icon. 
2. Select a 
Simulscan resolution as shown. Allow a few seconds 
for the projector to sync up after making the selection.
If you’re using a PC laptop:
❏Hold down the the Fn key and press the function key that 
lets you display on an external monitor. It’s often labelled 
with an icon such as   but it may also be labelled 
CRT/
LCD
. Allow a few seconds for the projector to sync up after 
pressing it. 
On most systems, the   or 
CRT/LCD key lets you 
toggle between the LCD screen and the projector, or display 
on both at the same time. Check your laptop’s manual or 
online help for details.
❏Depending on your computer’s video card, you might need 
to use the Display utility in the Control Panel to make sure 
that both the LCD screen and external monitor port are 
enabled. See your computer’s documentation or online help 
for details.
Resizing the Image
Some computer images need to be resized to display in the 
projector’s native format. If only part of your computer image 
is displayed, you can correct it with the 
Resize button. 
❏Press the 
Resize button on the control panel or remote 
control. The screen image is automatically compressed.
❏Continue pressing the 
Resize button to pan around the 
screen in the original resolution. 
If you’re projecting from video equipment, pressing the 
Resize button switches the aspect ratio between 4:3 and 16:9. 
If you’ve zoomed in on your image (using the 
E-Zoom button 
on the remote), you can press the 
Resize button to restore the 
original display size.
Click here
Drag one monitor 
icon on top of 
the other
Click here
Select a 
Simulscan 
resolution 
						

							EPSON PowerLite 600p/800p/810p Projectors
6 - EPSON PowerLite 600p/800p/810p Projectors 8/01 Adjusting the Image Shape
If the projected image isn’t square or has a “keystone” shape, 
do one or more of the following:
❏If your image looks like   or  , you’ve placed the 
projector off to one side of the screen, at an angle. Move it 
directly in front of the center of the screen, facing the screen 
squarely. If you still can’t get a square image, press the left or 
right 
Keystone button on the projector’s control panel.
❏If your image looks like   or  , press the top or 
bottom 
Keystone button to correct the shape of the image. 
After correction, your image will be slightly smaller.
You can also perform electronic keystone correction using the 
projector’s Setting menu. 
Switching Between Picture Sources
If your projector is connected to more than one computer 
and/or video source, you can use the buttons on the control 
panel (or remote control) to switch between the different 
sources. 
On the control panel, press the 
Computer/YCbCr button to 
switch between computer sources and component video. Press 
the 
Video button to switch between standard (composite) 
video and S-Video sources. 
On the remote control:
❏Press the 
Comp2/YCbCr button to select a computer or 
component video source connected to the Computer 2/
Component Video port on the projector.
❏Press the 
Comp1 button to select a computer connected to 
the DVI 
Computer 1 port on the projector. 
❏Press the 
Video button to select a standard composite video 
source.
❏Press the 
S-Video button to select an S-Video source. 
After you select a source, the screen goes dark for a moment 
before the image appears.
Projector Status Lights
The lights on top of the projector indicate the projector’s 
operating status.
Light Status Description and action
Does not 
come onMake sure the power cord is securely 
connected at both the power outlet and 
projector.
Green The projector is operating normally.
Flashing 
greenThe projector is warming up. Wait for the 
image to appear.
Orange The projector is in sleep mode. You can 
unplug it to turn it off, or press the Power 
button to turn it on.
Flashing 
orangeThe projector is cooling down. Wait for the 
light to stop flashing before unplugging the 
projector or turning it back on. 
Flashing red Power is cut off because of an internal 
problem. Disconnect the power cord and 
contact EPSON for help.
Red The lamp is burned out and must be replaced.
Flashing 
orangeThe lamp is almost burned out. This is a good 
time to replace it. 
Flashing red There is a problem with the lamp, power 
supply, fan, or circuit. If necessary, replace the 
lamp.
lamp lighttemperature 
light power light 
						

							EPSON PowerLite 600p/800p/810p Projectors
8/01 EPSON PowerLite 600p/800p/810p Projectors - 7
Using the Control Panel
The following table summarizes the functions on the control 
panel. 
Using the Remote Control
The remote control uses a line-of-sight infrared signal. It lets 
you access the projector’s features from anywhere in the 
room—up to 32 feet away. (This distance may be shorter if 
the remote control batteries are low.) If you have connected 
the mouse cable, you can also use the remote control as a 
wireless mouse.
The projector may not respond to remote control commands 
in these conditions: 
❏The remote control is not turned on (using the switch on its 
side)
❏You are too far away or not within 30
° to the left or right of 
the front or rear sensor or 15° above or below
❏Batteries are weak
❏Ambient light is too bright
❏A fluorescent light is shining into the infrared receiver
❏A strong light source (such as direct sunlight) shines into the 
infrared receiver
❏Other equipment emitting infrared energy is present (such as 
a radiant room heater)
Flashing 
orangeThe projector is too hot. Make sure the 
temperature surrounding the projector does 
not exceed 95 °F and there is plenty of space 
around and under the projector for ventilation. 
Clean the air filter if necessary.
Red The projector is overheating, which turns off 
the lamp automatically. Let it cool for a few 
minutes, then turn it back on. Make sure there 
is plenty of space around and under the 
projector for ventilation. If it continues to 
overheat, you may need to change the air 
filter. 
Flashing red There is a problem with the cooling fan or 
temperature sensor. Turn off the projector and 
unplug it. Contact EPSON for help.
Button Function
Power Starts or stops projection.
Help Displays the online help menu.
Computer/
YCbCrSwitches between the source connected to the 
Computer 1 port and the Computer 2/Component Video 
port.
Video Switches between composite video and S-Video.
Menu Displays or hides the menu screen.
Esc Stops the current function. Pressing Esc while viewing a 
menu or the online help displays the previous screen or 
menu.
Light Status Description and action
Volume Power
A/V MuteResize
Sync+
Tracking - Tracking +
Sync-
MenuSource
Esc Help
Computer/YCbCrVideo
Keystone
Shift
Auto
Sync + 
Sync –Use after tilting the projector (extending its foot) to 
square up the image. Corrects up to a ±30° tilt. Allows 
selection of a menu or menu options if the menu screen 
is displayed. When used with the Shift button, 
synchronizes the computer’s graphic signal. Use these 
buttons to adjust a fuzzy-looking image that contains a 
lot of fine detail. 
Tracking – 
Tracking 
+ Corrects horizontal keystone distortion, which occurs 
when the projector is not directly in front of the screen. 
Allows selection of menu options if the menu screen is 
displayed. When used with the Shift button, matches the 
projector’s internal clock to computer graphic signals. 
Use these buttons to eliminate vertical stripes or bands 
from an image that contains a lot of fine detail. 
 Enter, 
AutoSelects a menu option or the next menu/help screen. 
Pressing Enter when no menu or help screen is 
displayed optimizes the computer image.
Shift Press with the Sync or Tracking buttons to change their 
function from Keystone control to Sync or Tracking.
Resize Resizes non-standard computer video formats so they 
appear correctly on screen. Switches the aspect ratio 
between 4:3 and 16:9 when video images are being 
projected.
A/V Mute Turns off the audio and video. (In the menu system, you 
can set whether the screen appears black or blue, or 
displays a user logo.)
 Volume  Adjusts the volume.
Button Function 
						

							EPSON PowerLite 600p/800p/810p Projectors
8 - EPSON PowerLite 600p/800p/810p Projectors 8/01 The remote control buttons are shown in the following 
illustrations.This table summarizes the functions on the remote control.
  
Enter (pointer) button
Esc button Freeze
A/V Mute
E-Zoom
Special effects 
buttons (1-3)
Left mouse 
buttonsignal output
Power
On/off switch
Previous slide
Next slide
Menu
Comp1
Auto
P in P
Volume Help
Comp2/YCbCr
S-Video
Resize
Preset
Video
Button Function
Power Starts or stops the projector.
R/C on/off Turns the remote control on or off.
Freeze Keeps the current computer or video image on the 
screen.
A/V Mute Turns off the audio and video, displaying the black, 
blue, or user logo background.
Previous/Next 
slide buttonThe up arrow displays the previous slide; the down 
arrow displays the next slide. 
E-Zoom Changes the image size up to 4×. Pressing the right 
side of the button enlarges the image, pressing the left 
side reduces the image. To display a portion of an 
enlarged image which is outside the display area, 
press the Enter button and scroll the image to the 
desired location.
Effects buttons Displays special highlighting effects on the screen. 
Enter
(pointer button)Use the Enter button to navigate the menus or use the 
remote as a mouse pointer when the projector is 
connected to a computer with the mouse or USB 
cable. 
Esc Stops the current function. Pressing Esc while viewing 
a menu or the online help displays the previous screen 
or menu. When the image source is a computer, the 
Esc button acts as a mouse right-click.
Left mouse 
buttonWorks like the left button on a mouse when the 
projector is connected to a computer with the mouse 
or USB cable.
Menu Displays or hides the menu.
Help Displays the online help menu.
Comp1 Switches to the Computer 1 (DVI) image.
Comp2/YCbCr Switches to the Computer 2 or component video 
source.
Video Switches to the composite video source.
S-Video Switches to the S-Video source.
Auto Optimizes the computer image.
Resize Resizes SXGA and other video formats so they 
appear correctly on the screen. Switches the aspect 
ratio between 4:3 and 16:9 when video images are 
being projected. 
P in P Displays a video or S-Video image in a subscreen on 
the main display. Use the Enter button to reposition 
the Picture in Picture (P in P) screen, or the E-Zoom 
button to enlarge or reduce the image. Changes made 
to the P in P screen location and size are 
automatically carried over to the next P in P session. 
						

							EPSON PowerLite 600p/800p/810p Projectors
8/01 EPSON PowerLite 600p/800p/810p Projectors - 9 The three special effects buttons have the following functions.
Note: You can use the projector’s Effect menu to modify the 
highlighting effects for each of the numbered buttons.
Cleaning the Lens 
Warning: Before you clean any part of the projector, turn it off 
and unplug the power cord. Never open any cover on the 
projector, except the lamp and filter covers. Dangerous electrical 
voltages in the projector can injure you severely. Do not try to 
service this product yourself, except as specifically explained in this 
Product Information Guide. Refer all other servicing to 
qualified service personnel.
Clean the lens whenever you notice dirt or dust on the surface.
❏Use a canister of compressed air to remove dust.
❏To remove dirt or smears on the lens, use lens cleaning 
paper. If necessary, moisten a soft cloth with an alcohol-
based cleaner and gently wipe the lens surface.
Cleaning the Projector Case 
Before you clean the projector case, turn off the projector and 
unplug the power cord. 
❏To remove dirt or dust, wipe the case with a soft, dry, lint-
free cloth. 
❏To remove stubborn dirt or stains, moisten a soft cloth with 
water and a neutral detergent. Then wipe the case. 
❏Do not use wax, alcohol, benzene, thinner, or other chemical 
detergents. These can damage the case.
Cleaning or Replacing the Air Filter
Clean the air filter at the bottom of the projector after every 
100 hours of use. If it is not cleaned periodically, it can 
become clogged with dust, preventing proper ventilation. This 
can cause overheating and damage the projector.
Follow these steps:
1. Turn off the projector, allow it to cool down, and unplug the 
power cord.
2. Turn the projector on its side so that the handle is on top 
and you can access the filter easily.
3. To clean the filter, EPSON recommends using a small 
vacuum cleaner designed for computers and other office 
equipment. If you don’t have one, gently clean the filter 
using a very soft brush (such as an artist’s camel-hair brush).
If the dirt is difficult to remove or if the filter is torn, replace 
it. Contact your dealer or call EPSON at (800) 873-7766 in 
the United States and Canada to obtain a new one.
Note: When you get a replacement lamp for your projector, a 
new air filter is included. You should replace the filter when 
you replace the lamp.
Preset Saves and recalls up to five different session settings 
(resolution, tracking, sync signal, and position). To 
save the current session settings, press the Preset 
button and it will be assigned the next available 
number, 1 through 5. To recall a setting, press the 
Preset button a second time and move to the desired 
session number. To overwrite a saved setting, move 
to the setting you want to replace and press Enter. 
When the confirmation message displays, choose Yes 
and press Enter.
 Volume  Adjusts the volume.
Button Function
1 Changes the mouse cursor to a pointer or arrow.
2 Spotlights a section of the screen.
3 Lets you place a vertical or horizontal bar on the screen to 
highlight a part of your image.
Button Function 
						

							EPSON PowerLite 600p/800p/810p Projectors
10 - EPSON PowerLite 600p/800p/810p Projectors 8/01 4. If you need to replace the filter, make sure the projector is on 
its side as shown (not turned upside down) to prevent dust 
from falling inside. Then press the arrow tab to remove the 
filter.
5. To install the new filter, first insert the tabs, then press on 
the latch until it clicks in place.
Replacing the Lamp
The projection lamp typically lasts for about 1500 hours of 
use. It is time to replace the lamp when:
❏The projection image gets darker or starts to deteriorate.
❏The lamp warning light   is red or flashing red. 
❏The message 
LAMP REPLACE appears on the screen when 
the projector lamp comes on (after about 1400 hours of use). 
To maintain projector brightness and image quality, replace 
the lamp as soon as possible.
Note: You can check to see how many hours the lamp has been 
used through the About menu.
Contact your dealer or call EPSON at (800) 873-7766 in the 
United States and Canada for a replacement lamp. Request 
part number 
V13H010L15.
Warning: Be extremely careful when removing the lamp module. 
In the unlikely event that the bulb has ruptured, small glass 
fragments may be present and should be removed with caution. If 
your projector is mounted on the ceiling, you should unmount it 
before accessing the lamp compartment. This will make it easier 
for you to replace the lamp and minimize the chance of any small 
glass fragments dropping from the projector.
Follow these steps to replace the lamp:
1. Turn off the projector and unplug the power cord.
2. Allow the projector to cool down for at least half an hour (if 
it has been on).3. Use a screwdriver to slide the latch and pop open the lamp 
cover. Then lift it up and remove it.
4. Use a screwdriver to loosen the two silver screws holding the 
lamp in place. (You can’t remove these screws.)
5. Grasp the lamp as shown, and pull the lamp straight out.
Caution: Do not touch the glass portion of the lamp assembly.
6. Fully insert the new lamp. 
7. Once the lamp is fully inserted, tighten its screws.
8. To replace the lamp cover, insert the tabs and then snap the 
cover into place. (The projector won’t come on if the lamp 
cover is loose.)
arrow tab