Epson Powerlite 8000i Technical Specifications

EPSON PowerLite 8000i/9000i Projector
10/99 EPSON PowerLite 8000i/9000i Projector - 1
Projector Specifications 
General
Type of display Poly-silicon Thin Film Transistor (TFT)
Size of liquid
crystal panels    Diagonal: 1.3 inches (33.6 mm) 
Lens F=1.8 to 2.3, f=49 to 69 mm
Resolution 1024
 ´ 768 pixels (8000i)
1366  
´ 1024 pixels (9000i)
Color reproduction 24 bit, 16.7 million colors
Brightness 2200 lumens (ANSI) 8000i
1700 lumens (ANSI) 9000i
Image size Wide angle: 30 to 320 inches (at 3.6 to
 43.3...

EPSON PowerLite 8000i/9000i Projector
2 - EPSON PowerLite 8000i/9000i Projector 10/99 Remote IR Receiver
Supports EPSON Remote IR Receiver, 10-foot cable (typical 
use for rear screen projection)
Mechanical
Height 6.1 inches (157 mm), including feet
Width 12 inches (305 mm)
Depth 19.8 inches (475 mm), including lens
Weight 18.3 lb. (8.3 kg)
Electrical
Rated frequency 50 to 60 Hz
Power supply 100 to 120 VAC, 2.4 A
200 to 240 VAC, 1.2 A
Power 
consumption Operating: 360 W
Standby: 12 W
Environmental...

EPSON PowerLite 8000i/9000i Projector
10/99 EPSON PowerLite 8000i/9000i Projector - 3
Computer 1 and Computer Out 
Connector Pin Assignments
The Computer 1 and Computer Out connectors are female 
video RGB, 15-pin micro-D-style connectors. The pin 
assignments are:
Projector Placement Guidelines
To get the best results when projecting your images, it is 
important to position the projector at the proper height and 
distance relative to the screen.
When projecting from a table or desk, place the projector...

EPSON PowerLite 8000i/9000i Projector
4 - EPSON PowerLite 8000i/9000i Projector 10/99 To determine the projection distance when you know the 
diagonal size of the screen image:
oInches:
Maximum projection distance = (1.967 ´ diagonal size) – 3.224
Minimum projection distance = (1.554 ´ diagonal size) – 3.563
oCentimeters:
Maximum projection distance = (4.996 ´ diagonal size) – 8.1889
Minimum projection distance = (3.947 ´ diagonal size) – 9.0500
For example, here are the measurements for three...

EPSON PowerLite 8000i/9000i Projector
10/99 EPSON PowerLite 8000i/9000i Projector - 5
Projection Lamp Light
Temperature Light
Using the Remote Control
The remote control uses a line-of-sight infrared signal. To use 
the remote control, point it toward one of the remote control 
receivers located at the front and back of the projector. You 
can use the remote control up to about 32.8 feet (10 meters) 
from the projector. (This distance may be shorter if the remote 
control batteries are low.) You must...

EPSON PowerLite 8000i/9000i Projector
6 - EPSON PowerLite 8000i/9000i Projector 10/99 This table summarizes the functions on the remote control.
  Using the Control Panel 
You can use the control panel to control the projector instead 
of the remote control. However, you can program and access 
the custom features only with the remote control.
The following table summarizes the functions on the control 
panel: 
Button Function
Power Starts or stops the projector.
Freeze Keeps the current computer or...

EPSON PowerLite 8000i/9000i Projector
10/99 EPSON PowerLite 8000i/9000i Projector - 7
Cleaning the Lens 
Warning: Before you clean any part of the projector, turn off the 
projector and unplug the power cord. Never open any cover on the 
projector, except the lamp and filter covers. Dangerous electrical 
voltages in the projector can injure you severely. Do not try to 
service this product yourself, except as specifically explained in this 
Product Information Guide. Refer all other servicing to...

EPSON PowerLite 8000i/9000i Projector
8 - EPSON PowerLite 8000i/9000i Projector 10/99 3. Use a screwdriver to loosen the two retaining screws on the 
lamp cover. When the screws are loose, lift off the lamp 
cover. (You cannot remove these screws from the cover.)
4. Use a screwdriver to loosen the three screws holding the 
lamp unit in place. (You cannot remove these screws 
completely.) Then lift up the handle and pull out the lamp 
unit. 
5. Gently insert the new lamp unit by lowering it into position....