Epson Powerlite 750c Specifications

							Epson PowerLite 750c/760c Projector
8/05 Epson PowerLite 750c/760c Projector - 11 Warning: 
Except as specifically explained in the User’s Guide, do not attempt 
to service this product yourself.
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface. 
❏Use a canister of compressed air to remove dust. 
❏To remove dirt or smears on the lens, use lens-cleaning 
paper. If necessary, moisten a soft cloth with lens cleaner and 
gently wipe the lens.
Caution:
Do not use glass cleaner to clean the lens and do not spray liquid of 
any kind directly on the lens. Spray the cleaner on a soft cloth and 
then gently wipe the lens with the cloth.
Cleaning the Projector Case
Turn off the projector and unplug the power cord before you 
clean the case. 
To remove dirt or dust, wipe the case with a soft, dry, 
lint-free cloth. 
To remove stubborn dirt or stains, wipe the case with a soft 
cloth moistened with a mild detergent. 
Caution:
Do not use wax, alcohol, benzene, paint thinner, or other chemical 
detergents. These can damage the case. Do not spray cleaner directly 
on the projector.
Cleaning and Replacing the Air Filter
Clean the air filter and air intake vents on the bottom of the 
projector after every 100 hours of use. If not cleaned 
periodically, they can become clogged with dust, preventing 
proper ventilation. This can cause overheating and damage the 
projector. 
Follow these steps:
1. Turn off the projector, allow it to cool down, and unplug the 
power cord.
2. Turn the projector upside down.
Use a small vacuum cleaner designed for computers and 
other office equipment. If you don’t have one, use a very soft 
brush (such as an artist’s paintbrush).
If dirt is difficult to remove or the filter is torn, replace it. 
The air filter set (part number 
V13H134A08) contains two 
filters. See page 13 for ordering information. 
Red The projector is overheating, which turns 
the lamp off automatically. Wait until the 
cooling fan stops, then unplug the power 
cord. Plug the power cord back in and 
press the P Power button. Make sure the 
room temperature is not above 95 °F 
(35 °C), and there is plenty of space around 
and under the projector for ventilation. 
The air filters may be clogged. Clean or 
replace them as described in the next 
column. If the projector continues to 
overheat after you clean the air filter, the 
problem may be caused by damage to the 
cooling fan or temperature sensor. Contact 
Epson for help.
Flashing 
orangeIt’s time to replace the lamp. (See 
page 12.) If you continue to use the lamp 
after the replacement warning, there is an 
increased possibility that the lamp may 
break.
Flashing 
redThe lamp may be burnt out. First make 
sure the lamp cover is securely installed. If 
that’s not the problem, let the lamp cool, 
remove the lamp, and replace it as 
described on page 12. If this does not 
resolve the problem, contact Epson.
Flashing 
redPower is cut off because of an internal 
problem. Unplug the power cord and 
contact Epson for help. Light Status Description 
						

							Epson PowerLite 750c/760c Projector
12 - Epson PowerLite 750c/760c Projector 8/05 3. If you need to replace the filter, slide it off as shown.
4. Slide the new air filter until it clicks in place.
Replacing the Lamp 
The projection lamp typically lasts for about 2000 hours of use 
(in High Brightness mode) or 3000 hours (in Low Brightness 
mode). It is time to replace the lamp when: 
❏The projected image gets darker or starts to deteriorate.
❏The message 
Replace the Lamp appears on the screen when 
the lamp comes on and the   warning light flashes orange. 
To maintain brightness and image quality, replace the lamp 
as soon as possible.
❏The lamp   warning light flashes red (the lamp is burnt 
out).
You can check how many hours the lamp has been used in the 
Info menu.
Note:
Turn the projector off when not in use. Continuous use may reduce 
the life of the product.
See page 13 for ordering information and request part number 
V13H010L32. 
Follow these steps to replace the lamp:
1. Turn off the projector.
2. When the 
Power light stops flashing, unplug the power 
cord.
3. If the projector has been on, allow it to cool down for at least 
an hour (or until the lamp is cool). 
Warning:
Let the lamp cool before replacing it. In the unlikely event that the 
lamp has broken, small glass fragments may be present and should 
be removed carefully to avoid injury.4. Turn the projector over. Press in on the tabs and lift up the 
lamp cover.
5. Loosen the two screws holding the lamp in place (you don’t 
need to remove them).
6. Hold the lamp as shown and pull it straight out.
7. Gently insert the new lamp. (If it doesn’t fit easily, make sure 
it is facing the right way.)
Warning:
The lamp(s) in this product contain mercury. Please consult 
your state and local regulations regarding proper disposal or 
recycling. Do not place in the trash.
Caution:
Do not touch the glass portion of the lamp assembly. Touching 
the glass could result in premature lamp failure.
8. Once the lamp is fully inserted, tighten its screws.
9. Insert the two cover tabs, then press down on the cover until 
it snaps into place.
10.Reset the lamp timer as described in the next section.  
						

							Epson PowerLite 750c/760c Projector
8/05 Epson PowerLite 750c/760c Projector - 13
Resetting the Lamp Timer
You must reset the lamp timer after replacing the lamp to clear 
the 
Replace the Lamp message.
Note:
Do not reset the lamp timer if you have not replaced the lamp. If 
you do, the 
Lamp Hours will not accurately reflect the number of 
hours that the lamp has been used.
1. Connect the power cable and turn on the projector.
2. Press the 
Menu button on the remote control and select the 
Reset menu. Then press Enter. You see this screen:
3. Select 
Lamp-Hours Reset and press Enter. You see this 
prompt:
4. Select 
Yes and press Enter.
5. Press 
Esc to return to the Reset menu or the Menu button 
to exit the menu system. 
Optional Accessories
Epson provides the following optional accessories for the 
projectors. 
You can purchase these accessories from an Epson authorized 
reseller. For product information and to find the nearest 
reseller, please call (800) GO-EPSON (800-463-7766). 
To purchase online, visit www.epsonstore.com (U.S. sales 
only). In Canada, please call 800-463-7766 for reseller referral.
Related Documentation
CPD-20247Epson PowerLite 750c/760c User’s Guide
CPD-20249Epson PowerLite 750c/760c Quick Setup
Product Part number
Replacement lamp  V13H010L32 
Air filter set (includes 2 filters) V13H134A08
Samsonite
® wheeled soft case 
ATA molded hard-shell carrying case
Notebook/projector soft shoulder bagELPKS35-S
ELPKS42
ELPKS43
Component video cable (VGA-to-RCA) ELPKC19
S-Video cable ELPSV01
Macintosh adapter set  ELPAP01
Distribution amplifier ELPDA01
50-inch portable screen
60-inch portable pop-up screen
80-inch portable pop-up screen
83.6-inch hanging pull-down screenELPSC06
ELPSC07
ELPSC08
ELPSC09
High resolution document imager V12H162020
Kensington
® security lock ELPSL01
Universal ceiling mount
False ceiling plate
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channelELPMBUNI
ELPMBFCP
ELPMBSEC
ELPMBACC