Epson Powerlite 745c Technical Specifications

							Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 1
Projector Parts
Specifications
General
Type of display Poly-silicon TFT active matrix
Resolution 1024 
× 768 pixels (XGA)
(native format)
Color  24-bit, 16.8 million colors
reproduction
Brightness  2500 lumens (High Brightness mode)
(ANSI) 2000 lumens (Low Brightness mode)
Contrast ratio 400:1
Image size 30 to 300 inches (0.8 to 7.6 meters)
Projection  3.2 to 39.7 feet (1.0 to 12.1 meters)
distanceProjection  Front, rear, upside-down (ceiling mount)
methods
Internal  1 W monaural 
sound system
Optical aspect  4:3 (horizontal:vertical)
ratio
Zoom ratio 1 : 1.2
Noise level 36 dB (Low Brightness mode)
Mouse Supports USB (type B)
compatibility
Projection Lamp
Type UHE (Ultra High Efficiency)
Power 170 W 
consumption
Lamp life High Brightness mode: about 2000 hours
Low Brightness Mode: about 3000 hours
Part number V13H010L32
Remote Control
Range 20 feet (6 meters)
Batteries (2) Alkaline AAA
Dimensions
Height 2.7 inches (70 mm), feet retracted
Width 10.9 inches (276 mm)
Depth 7.6 inches (193 mm)
Weight 3.9 lb (1.8 kg) 
Electrical 
Rated frequency 50/60 Hz AC
Power supply 100 to 120 VAC, 2.7 A
200 to 240 VAC, 1.1 A 
Power Operating: 240 W
consumption
Environmental
Temperature Operating: 41 to 95 °F (5 to 35 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Humidity  Operating: 20 to 80% RH,
(non-condensing) Storage: 10 to 90% RH
I/R receiverLens cap
Exhaust air vent
Foot adjust leverSecurity lock
Control panel
Zoom ringFocus ringCard slot
SpeakerRear adjustable 
footPower inlet
USB port
(Type B)
Audio portComputer/
Component 
Video portVideo port
S-Video port
USB port
(Type A) 
						

							Epson PowerLite 745c Projector
2 - Epson PowerLite 745c Projector 8/04
Safety and Approvals
United States FCC 47CFR Part15B Class B (DoC)
UL60950 Third Edition
Canada ICES-003 Class B
CSA C22.2 No. 60950 
CE Marking Directive 73/23/EEC, 89/336/EEC
IEC60950 Third Edition
EN 55022, EN 55024
Compatible Video Formats
The projector supports the video display formats listed below:
Compatible Computer Display Formats
To project images from a computer, set the computer’s video 
card at a refresh rate (vertical frequency) compatible with the 
projector; see the following table for compatible formats. Some 
images are automatically resized to display in the projector’s 
“native” format (XGA). The frequencies of some computers 
may not allow images to display correctly; see your computer’s 
documentation for details. 
*The image is resized using Epson’s SizeWise™ Technology.
Mode Refresh Rate (Hz)
NTSC
NTSC 4:43
PAL
N—PAL
M—PAL
PAL—60
SECAM60
60
50
50
60
60
50
HDTV (720p)
HDTV (720p)
HDTV (1080i)
HDTV (1080i)
SDTV (480p)
SDTV (480p)
TV480i
TV480i60
50
60
50
60
50
60
50
Mode Refresh Rate (Hz) Resolution
VGA EGA
VGA—60
VESA—72
VESA—75
VESA—8570
60
72
75
85640 
× 350*
640 
× 480*
640 
× 480*
640 × 480*
640 
× 480*
SVGA—56
SVGA—60
SVGA—72
SVGA—75
SVGA—8556
60
72
75
85800 
× 600*
800 × 600*
800 
× 600*
800 
× 600*
800 × 600*
XGA—60
XGA—70
XGA—75
XGA—8560
70
75
851024 
× 768 
1024 × 768 
1024 × 768 
1024 × 768 
SXGA1—70
SXGA1—75
SXGA1—8570
75
851152 × 864*
1152 × 864*
1152 
× 864*
SXGA2—60
SXGA2—75
SXGA2—8560
75
851280 
× 960*
1280 × 960*
1280 
× 960*
SXGA+60
SXGA+75
SXGA+8560
75
851400 
× 1050*
1400 
× 1050*
1400 × 1050*
SXGA3—60
SXGA3—75
SXGA3—8560
75
851280 
× 1024*
1280 
× 1024*
1280 × 1024*
UXGA—60 60 1600 
× 1200* 
iMAC VGA
iMAC SVGA
iMAC XGA
MAC13
MAC16
MAC19—60
MAC19
MAC21117
95
75
67
75
59
75
75640 × 480*
800 × 600*
1024 
× 768 
640 × 480*
832 × 624*
1024 
× 768 
1024 × 768 
1152 × 870* 
						

							Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 3
Positioning the Projector
Before connecting the projector, you need to decide where to 
place it. The location you choose depends on the size of the 
room and what you are projecting.
❏Place the projector on a sturdy, level surface, between 
3.2 and 39.7 feet from the screen.
❏Make sure there is plenty of space for ventilation around and 
under the projector. Do not set the projector on top of 
anything that could block the vents under the projector.
❏Make sure the projector is within 10 feet of an electrical 
outlet or extension cord and within 5 feet of your computer 
and/or video source, unless you are projecting wirelessly or 
from a memory card.
❏Place the projector directly in front of the center of the 
screen, facing the screen squarely. Otherwise, your image 
will not be rectangular.
Note:
It’s easier to position the projector when the screen is directly in 
front of the room. 
Use the figure below as a guideline to help you determine how 
far from the screen to place the projector. Image size generally 
increases with distance, but may vary depending on how you 
position the zoom ring and whether you have adjusted the 
image size with other settings. 
To calculate exact measurements, use the following formulas: 
❏To find the projection distance when you know the screen’s 
diagonal dimension:
Wide (inches) = ((33.696 
× diagonal screen size [inches]) –
21.717) / 25.4
Tele (inches) = ((40.453 
× diagonal screen size [inches]) – 
22.52) / 25.4
❏To find how large a screen’s diagonal dimension will be 
when you know the projection distance:
Wide (inches) = (Projection distance [inches] 
× 0.0254 + 
0.02171) / 0.033696
Tele (inches) = (Projection distance [inches] 
× 0.0254 + 
0.02252) / 0.040453If you place the projector below the level of the screen, you’ll 
have to tilt it up by extending the front adjustable foot, as 
shown. Tilting the projector upward causes the image to lose its 
rectangular shape, but you can correct the distortion by pressing 
the 
Sync buttons on the projector. See page 6 for detailed 
information about correcting the image shape.
If you place the projector level with the bottom of the screen, 
the image will be rectangular and you won’t have to adjust it. If 
you place the projector higher than the bottom of the screen, 
the image will still be rectangular, but you won’t be able to fill 
the whole screen with the image. 
Starting Up the Projector
Make sure your projector and other equipment are set up and 
connected correctly. Then turn on your projector, as described 
below. 
If you turn on your connected computer or video equipment 
before starting the projector, the projector automatically detects 
and displays the image source. If you turn on the projector first, 
or have multiple pieces of connected equipment, you may have 
to select the image source manually. See “Selecting the Image 
Source” on page 5.
Follow these steps to plug in and turn on the projector:
1. Remove the lens cap.
Caution
Do not use the projector with the lens cap in place. The heat 
generated by the lamp can damage the cap.
2. Connect one end of the power cord to the projector’s power 
inlet. Then connect the other end to an electrical outlet. 
The P 
Power light on top of the projector turns orange, 
indicating that the projector is receiving power but not yet 
turned on. 
33.1 to 39.7 feet 6.6 to 7.9 feet 3.2 to 3.9 feet 
						

							Epson PowerLite 745c Projector
4 - Epson PowerLite 745c Projector 8/04 3. Press the P 
Power button on top of the projector or on the 
remote control. 
The projector beeps once and the P 
Power light flashes 
green as the projector warms up, then an image begins to 
appear. When the P 
Power light stops flashing and remains 
green, the projector is ready for use. 
Warning:
Never look into the lens when the lamp is on. This can damage 
your eyes, and is especially dangerous for children.
❏If you’ve connected a Windows
®-based computer to the 
projector, you may see a New Hardware Wizard saying 
your computer has found a plug-and-play monitor; if so, 
click 
Cancel.
❏If you don’t see the image you want, press the 
Source 
Search button on the projector or the Search button on 
the remote control until you see the image you want to 
project.
❏If you are prompted to enter a password, see “Starting the 
Projector with a Password” on page 10.
Note:
You can also use the Source buttons on the remote control to 
switch between devices connected to the ports identified on each 
button. For details, see page 5.
If a projected image fails to appear, see “What To Do If You See 
a Blank Screen” in the next column. 
When you’re done with your presentation, shut down the 
projector as described on page 7. Shutting down the projector 
correctly prevents premature lamp failure and possible damage 
from overheating. 
What To Do If You See a Blank Screen
If you see a blank screen or the No Signal message after turning 
on your computer or video source, try the following:
❏Make sure the cables are connected correctly.
❏Make sure the P 
Power light is green and not flashing and 
the lens cover is off. 
❏Press the 
Source Search button on the projector or the 
Search button on the remote control repeatedly until you 
see the image you want to project. See page 5 for more 
information about selecting the image source.
If you’re using a Windows computer:
❏Hold down the Fn key and press the function key that lets 
you display on an external monitor. It may have an icon such 
as   or it may be labelled 
CRT/LCD. Allow a few seconds 
for the projector to sync up after pressing it. Check your 
computer’s manual or online help for details. 
On most systems, the   or 
CRT/LCD key lets you toggle 
between the LCD screen and the projector, or display on 
both at the same time. 
❏Depending on your computer’s video card, you might need 
to use the Display utility in the Control Panel to make sure 
that both the LCD screen and external monitor port are 
enabled. See your computer’s documentation or online help 
for details.
If you’re using a Macintosh® with OS X:
You may need to set up your system to display on the projector 
screen as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
System Preferences, then 
click 
Displays.
2. Select 
VGA Display or Color LCD, click Arrange or 
Arrangement, and make sure Mirror Displays is checked.
If you’re using a Macintosh with OS 8.6 to 9.x:
You may need to set up your system to display on the projector 
screen as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
Control Panels, then click 
Monitors or Monitors and Sound.
2. Click the 
Arrange icon.
3. Drag one monitor icon on top of the other. 
If the 
Arrange option isn’t available, try selecting one of the 
Simulscan resolution settings. Click the 
Monitor icon, if 
necessary, and then select a 
Simulscan resolution. (Allow a few 
seconds for the projector to sync up after making the selection.)
Remote control Projector
Power button 
						

							Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 5
Selecting the Image Source
If multiple devices are connected to the projector, the easiest 
way to select the image source is to press the 
Search button on 
the remote control or the 
Source Search button on the 
projector until the correct image is projected.
You can also press one of the following buttons on the 
remote control:
❏
Computer to select the device connected to the projector’s 
Computer/Component Video port. 
❏
S-Video to select the device connected to the 
S-Video port.
❏
Video button to select the device connected to the 
Video port.
❏
EasyMP button to project wirelessly or from a memory 
card.
After you select a source, the screen goes dark for a moment 
before the image appears. 
Adjusting the Image
Once you see your image, you may need to make certain 
adjustments, as described in this section.
Focusing and Zooming Your Image
Rotate the focus ring to sharpen the image.
Rotate the zoom ring to reduce or enlarge the image.You can also change the image size by moving the projector 
closer to or farther away from the screen. You can use the 
E-Zoom buttons on the remote control to zoom in on a portion 
of the image. See “Zooming Your Image” on page 7 for 
instructions. 
Adjusting the Height of Your Image
If the image is too low, you can raise it by extending the 
projector’s front adjustable foot.
 
1. Stand behind the projector. Press up on the blue foot release 
lever and lift the front of the projector to extend the front 
adjustable foot.
2. Once the image is positioned where you want it, release the 
lever to lock the foot in position.
3. If the projector is not level, rotate the 
foot at the back of the projector.
If the image is no longer rectangular after 
raising it, see the next section.
Correcting Computer 
Images
If you’ve connected a computer and the image doesn’t look 
right, or it doesn’t fit properly on the screen, press the 
Auto 
button on the remote control or the 
Enter button on the 
projector. This automatically resets the projector’s tracking, 
sync, resolution, and position settings. You must be projecting 
an image for this button to have any effect. Additionally, if the 
Auto Setup option in the Signal menu is set to OFF, the Auto 
function will not work.
Focus ring
Zoom ring 
						

							Epson PowerLite 745c Projector
6 - Epson PowerLite 745c Projector 8/04 Adjusting the Image Shape
The projector automatically corrects images that are distorted 
when the projector is tilted up or down (up to a 15° tilt). The 
Keystone window appears on the screen while the projector 
makes the correction. If the projected image still isn’t 
rectangular or has a “keystone” shape, do one or more of the 
following:
❏If your image looks like  or  , you’ve placed the 
projector off to one side of the screen, at an angle. Move it 
directly in front of the center of the screen, facing the screen 
squarely.
❏If your image looks like   or  , you may need to 
manually adjust the keystone correction value. Follow the 
directions below:
❏To make keystone corrections using the projector’s 
Setting menu, press the 
Menu button on the projector or 
remote control. Select the 
Setting menu, then press 
Enter. Select Keystone and press Enter. Use the   
pointer button on the remote control (or the arrow 
buttons on the projector) to adjust the keystone setting as 
needed.
❏To manually adjust the keystone correction value, press 
the   or   button on the projector to correct the 
shape of the image. After correction, your image will be 
slightly smaller.
Adjusting the Brightness
The brightness of an image depends on the source you are 
projecting and the amount of light in the room. If the image is 
too bright or not bright enough, do one of the following:
❏Change the 
Brightness setting in the Image menu. 
❏Select 
Low or High for the Brightness Control option in 
the Setting menu. Low Brightness mode extends the life of 
the lamp and decreases the fan noise.
Adjusting the Color Mode
You may want to adjust the color mode to select a setting 
that is appropriate for the image you’re projecting and the 
environment in which you’re projecting it.
The following table lists the available color modes.  
To change the color mode, press the 
Color Mode button on 
the remote control until you see the mode you want. The 
currently selected setting appears in the upper right corner of 
the screen. You can also use the projector menu system to select 
the Color Mode in the Image menu.
Sleep Mode
When the projector has not received any input signals for 
30 minutes, it automatically turns off the projector lamp and 
enters “sleep mode.” This conserves electricity, cools the 
projector, and extends the life of the lamp. If you are done using 
the projector, unplug the power cord. If you want to start 
projecting again, press the P 
Power button. 
You can enable sleep mode in the Extended menu under 
Operation.
Color mode Description
sRGBFor matching the color palette of standard sRGB 
computer displays.
DynamicFor increased brightness in bright rooms (the 
default for non-computer display).
PresentationFor computer presentations (the default when 
projecting from a computer with analog video).
TheaterFor optimizing movie images with increased 
contrast.
Living RoomFor increased brightness when playing video 
games or watching TV in a bright room.
BlackboardFor projecting accurate colors on a green 
chalkboard (adjusts the white point). 
						

							Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 7
Using Direct Power On
The Direct Power On function enables faster setup. The 
projector will start up automatically when you plug it in; you 
won’t have to press the P 
Power button.
Follow these steps to enable Direct Power On:
1. Press the 
Menu button on the remote control and select the 
Extended menu.
2. Choose 
Operation and press Enter.
3. Choose 
Direct Power On and press Enter.
4. Highlight 
ON and press Enter.
5. Press 
Esc or Menu to exit.
Note:
When Direct Power On is enabled, shut down the projector as you 
normally would. Follow the instructions in the next section. (The 
projector will start automatically when power is restored after a 
power failure if it is plugged in.)
Shutting Down the Projector
When you’ve finished using the projector, follow the 
recommended procedure to shut it down. This extends the 
lamp life and protects the projector from possible overheating. 
1. Turn off any equipment plugged into the projector.
2. To turn off the projector, press the P 
Power button on the 
projector or remote control. You see a confirmation message. 
(If you don’t want to turn it off, press any other button.)
3. Press the P 
Power button again. The P Power light flashes 
orange as the projector cools down. When the projector 
beeps twice, it’s safe to unplug it.
To turn the projector on again, wait until the P 
Power light 
stops flashing. Then press the P 
Power button.
4. Press up on the blue foot release lever and lower the 
projector to retract the front adjustable foot, as shown.
5. Replace the lens cap and unplug the power cord.Caution
To avoid damaging the projector or lamp, never unplug the 
power cord when the P 
Power light is green or flashing orange.
Using the Remote Control
Before using the remote control, insert the two AAA alkaline 
batteries, as described on page 8.
When using the remote control, stand within 20 feet of the 
projector. Point the remote control either at the projector or at 
the screen (the projector’s front sensor can detect signals 
bounced off the screen). Press the button for the function you 
want to use. 
Turning Off the Picture and Sound
You can use the A/V Mute button on the remote control to turn 
off the image and sound. This is useful if you want to 
temporarily redirect your audience’s attention.
❏To turn off the picture and sound, press the 
A/V Mute 
button. The screen turns blue.
❏To turn the image and sound back on, press the 
A/V Mute 
button again.
You can create an image, such as a company logo or a picture, to 
display on the screen whenever you press the 
A/V Mute button. 
See the User’s Guide for more information.
Stopping Action 
Press the Freeze button to stop the action in your video or 
computer image and keep the current image on the screen. The 
sound will continue.
To restart the action, press the 
Freeze button again or 
press
 Esc.
Zooming Your Image
Follow these steps to zoom in on a portion of the image:
1. Press the 
E-Zoombutton on the remote control. You see 
a crosshair indicating the center of the zoom-in area.
2. Use the  pointer button to position the crosshair in the 
area you want to enlarge.
3. Continue pressing the 
E-Zoombutton to enlarge the 
selected area up to 4 times. 
						

							Epson PowerLite 745c Projector
8 - Epson PowerLite 745c Projector 8/04 4. While the image is enlarged, you can:
❏Use the  pointer button to move around the screen.
❏Press the 
E-Zoombutton to zoom out. 
5. When you’re done, press the 
Esc button to return the image 
to its original size.
Using the Remote Control as a Wireless 
Mouse
When you use the remote control as a wireless mouse, you can 
control your computer or click through slideshow-style 
presentations (such as PowerPoint
®) from up to 20 feet away. 
To control your computer with the remote, make sure you have 
connected the USB mouse cable between the projector and your 
computer.
❏To advance slides in a PowerPoint presentation in Slide 
Show mode, press the 
Page Up button on the remote 
control. Press the 
Page Down button to go back a slide.
❏To display the mouse pointer, press the 
Pointer button.
❏To move the pointer on the screen, aim the remote at the 
screen and use the  pointer button.
❏To click (or left-click), press the 
Enter button.
❏To right-click, press the 
Esc button.
❏To double-click, press the 
Enter button twice.
❏To click and drag, press and hold the 
Enter button and use 
the  pointer button to move the pointer, then release the 
Enter button.
Replacing the Batteries
Caution:
When replacing batteries, take the following precautions:
❏Replace the batteries as soon as they run out. If a battery leaks, 
wipe away battery fluid with a soft cloth. If fluid gets on your 
hands, wash them immediately.
❏Do not expose batteries to heat or flame.
❏Dispose of used batteries according to local regulations.
❏Remove the batteries if you won’t be using the projector for a 
long time. 
Follow these steps to replace the AAA alkaline batteries:
1. Press in the tab to remove the battery cover.
2. Remove the old batteries, then insert the new ones as shown.
3. Replace the battery cover. (It should snap into place.)
Page up or 
page downMove the pointer
Left-click or 
double-clickRight-click
Display the 
pointer 
						

							Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 9
Using Password Protection
If you assign a password for the projector, a screen appears 
requesting the password whenever you turn on the projector. If 
you enter the password incorrectly three times in succession, the 
projector’s operation is locked. Disconnect the projector and 
reconnect it. If you enter the incorrect password 30 times in a 
row, the projector is locked and remains locked until an 
authorized Epson servicer can unlock it.
You can also create a user’s logo for the projector, to be 
displayed as the startup screen and/or AV/Mute screen. 
Unauthorized users cannot turn it off or change it. This 
discourages theft and provides a way to identify the projector 
should it be stolen. 
Additionally, to make sure a borrowed projector is returned, 
you can temporarily disable the password for a set period of 
time. When that time has elapsed, the password function is 
reactivated and you must enter the password before you can use 
the projector.
Follow the instructions below to set the password, and then 
turn on the password and/or user logo protection.
Note:
If you should happen to enable the password before you set one, and 
you see the prompt to enter the password, enter the default password 
0000 to proceed.
Setting a Password 
1. Press the Freeze button on the remote control for about 
5 seconds, until you see the Password Protect menu:
If a password has already been set, you see the Password 
Protect Release screen. See “Starting the Projector with a 
Password” on page 10.
2. Select 
Password and press Enter. You see the message 
Change the password?
3. Select Yes and press Enter.4. Hold down the 
Num button 
on the remote control and use 
the numeric keypad to enter a 
4-digit password.
The password will be 
displayed as 
****. After you 
enter the last digit, a 
confirmation screen appears. 
Enter the password again.
5. After you finish setting the 
password, press the 
Esc 
button to return to the 
Password Protect menu.
6. Press the 
Num button to deactivate the numeric keypad.
Make a note of the password and keep it in a safe place in case 
you forget it. 
Turning On the Password and User’s Logo
To enable the password and User’s Logo, follow these steps:
1. Press the 
Freeze button on the remote control for about 5 
seconds until you see the Password Protect menu.
2. Select 
Power ON Protect and press Enter. 
3. Select 
ON and press Esc. 
4. If you want to disable the password temporarily so someone 
can use the projector without entering the password, select 
Timer and press Enter. Then hold down the Num button 
while you use the numeric keypad to enter the number of 
hours (from 0 to 9999) you want the password feature 
disabled. If you want the projector to request the password 
every time it is turned on, set the timer to 
0H. 
The timer starts counting as soon as you close the Password 
Protect menu. (You can check the elapsed time in this menu 
next to 
Time elapsed.)
When the period defined in the Time-elapsed setting has 
passed, and the password is entered correctly, the elapsed 
time will be reset to 
0H and the timer will start again. 
Remember to disable or change this setting when you’re 
finished using it.
5. To enable your User’s Logo, select 
User’s Logo Protect and 
press 
Enter. Then select ON and press Enter. 
When this feature is on, the logo appears whenever the 
projector is turned on (if the 
Startup Screen is enabled in 
the Extended menu) and as the A/V Mute screen (if you 
selected 
Logo as the Background Color in the Extended 
menu). 
Note:
None of the User’s Logo features can be changed when the User’s 
Logo Protect function is enabled.
Numeric keypad Num button 
						

							Epson PowerLite 745c Projector
10 - Epson PowerLite 745c Projector 8/04 6. Press 
Menu to close the Password Protect menu.
Starting the Projector with a Password
Caution:
If you lose the remote control, you will not be able to enter the 
password; so keep the remote control in a safe place at all times. 
When the password function is enabled, you see this screen 
when you turn on the projector: 
Hold down the 
Num button on the remote control as you use 
the numeric keypad buttons to enter the password. Once you 
have entered the password correctly, the password screen closes, 
and projection begins.
If the password is not correct, you see the message 
Wrong 
password. Please try again
. If you enter an incorrect 
password three times in succession, you see the message 
The 
projector’s operation will be locked. Request code xxxxx
 
and the projector switches to standby mode for approximately 5 
minutes. Write down the request code. Then disconnect the 
projector’s power cord from the electrical outlet, reconnect it, 
and turn the projector back on. When you see the Password 
Protect Release screen, enter the correct password.
If you have forgotten the password, contact Epson for assistance 
and give them the request code number that appears in the 
Password Protect Release screen. 
If you enter an incorrect password 30 times in a row, the 
projector remains locked and you must contact an authorized 
Epson servicer to unlock it. 
Disabling the Projector’s Buttons
When you enable the Operation Lock function, all the 
projector’s buttons are disabled except the P 
Power button. 
This is useful, for example, if you want to prevent students in a 
classroom from playing with the projector.
1. Press the 
Menu button.
2. Select the 
Setting menu and press Enter.
3. Select 
Operation Lock and press Enter.
4. Select 
ON and press Enter. Then select Yes and press Enter 
to confirm the setting.
5. Press the 
Menu button to exit the menu system.
Note:
You can cancel Operation Lock by pressing the projector’s 
Enter 
button for 7 seconds.
Presenting Over a Wireless Network
Using EMP NS Connection, you can project images shown 
on your computer screen directly to your audience without 
connecting the projector to your computer. Before you begin, 
make sure you’ve installed EMP NS Connection from the 
CD-ROM that came with your projector. See the User’s Guide 
for installation instructions.
Starting EasyMP
™
Before you can connect to the projector wirelessly, you have to 
switch it to EasyMP mode.
1. Turn on the remote control and the projector. Press the 
EasyMP button on the remote control to select EasyMP as 
the source.
2. Locate the Epson 802.11G/B card that came with your 
projector. Insert it with the label facing upward.
Note: 
Only the Epson 802.11G/B card is guaranteed to work. 
Other cards may not be compatible.