Epson Powerlite 7200 Technical Specifications

							EPSON PowerLite 5300/7200/7300 Projector
1/99 EPSON PowerLite 5300/7200/7300 Projector - 1
Projector Specifications 
General
Type of display Poly-silicon Thin Film Transistor (TFT); 
PowerLite 5300 and 7300 models have a
Micro Lens Array (MLA) built in
Size of liquid 
crystal panels    Diagonal: 1.3 inches (33.6 mm) 
Lens F=2.0–2.3, f=55–72 mmResolution PowerLite 5300: SVGA, 800 
´ 600 pixels
PowerLite 7200/7300: XGA, 1024 
´ 768
pixels
Color 
reproduction 24 bit, 16.7 million colors
Brightness PowerLite 5300/7300: 1200 lumens (ANSI)
PowerLite 7200: 1000 lumens (ANSI)
Image size 30 to 300 inches (at 3.9 to 40.6 feet 
distance), Tele angle 
23 to 230 inches (at 5.1 to 54 feet
distance), Wide angle
Projection 
distance 3.9 to 54.7 feet (1.2 to 16.7 meters)
Projection 
methods Front, rear, upside-down (ceiling mount)
Internal speaker 
system 3 
´ 3 W stereo output
2 
´ 3 W 8 (ohm) speakers
Optical aspect 
ratio PowerLite 5300/7300: 4:3 (horiz.:vertical)
PowerLite 7200: 5:4 (SVGA); 4:3 (VGA,
SVGA, XGA); 16:9 (wide screen video)
Zoom ratio 1:1.3
Tilt angle 0° to 12°
Supported video 
interface standards NTSC, PAL, PAL-M, PAL-N, SECAM
Projection Lamp
Type UHE (Ultra High Efficiency)
Power 
consumption 120 W
Lamp life 2000 hours at 50% brightness
Part number ELPLP05
Remote Control
Range 32.8 feet (10 meters)
Batteries Alkaline AA (2)
Mouse Compatibility
Supports PS/2, serial, ADB
Repeater Interface
Supports Xantech
® IR repeaters,
3.5 mm stereo mini-jack
foot adjust 
lever
infrared receivercontrol panel
power lightstatus lights
infrared 
receiver
foot adjust lever
adjustable 
feet
1
power inletAudio Out Audio 1Audio 2
Mouse/Com 1 Mouse/Com 2
Repeater
Computer OutComputer 2
Computer 1 R/R-Y G/Y G Sync B/B-YBNC HD/Sync VD S-Video
Video L-Audio-R 
						

							EPSON PowerLite 5300/7200/7300 Projector
2 - EPSON PowerLite 5300/7200/7300 Projector1/99 Mechanical
Height 5.1 inches (130 mm), including feet
Width 11.8 inches (300 mm)
Depth 14.3 inches (363 mm), including lens
Weight 13.8 lb (6.2 kg)
Electrical
Rated frequency 50/60 Hz
Power supply 100 to 120 VAC, 2.4 A
200 to 240 VAC, 1.2 A
Power 
consumption Operating: 200 W
Standby: 8.4 W
Environmental
Temperature Operating: 41 to 104° F (5 to 40° C),
non-condensing
Storage: 14 to 140° F (–10 to 60° C),
non-condensing
Humidity Operating: 20 to 80% RH, 
non-condensing
Storage: 10 to 90% RH, 
non-condensing
Safety
United States FCC Part 15J Class B
UL1950 Rev. 3
Canada DOC SOR/88-475
CSA C22.2 No. 950 Rev. 3
Supported Monitor Displays
Here are the display formats supported by the projector:
Note: The frequencies of some computers may not allow the image 
to be displayed correctly.
Projector Placement Guidelines
To get the best results when projecting your images, it is 
important to position the projector at the proper height and 
distance relative to the screen.
When projecting from a table or desk, place the projector so 
the lens is aligned as closely as possible with the bottom of 
your screen:
When projecting from the ceiling, align the lens as closely as 
possible with the top of your screen:
Calculating Image Size and Projection 
Distance
The distance between the projector and the screen determines 
the actual image size. To determine the exact distance required 
for a particular image size (or to determine the size of an image 
at a particular distance), use the following formulas. 
(Remember that the size of the image can be changed by 
rotating the zoom ring.)
To determine the minimum and maximum diagonal size of an 
image when you know the projection distance:
oInches:
Maximum diagonal size = (0.6124 ´ projection distance) + 1.5264
Minimum diagonal size = (0.4556 
´ projection distance) + 1.1410
oCentimeters:
Maximum diagonal size = (0.6124 ´ projection distance) + 3.8771
Minimum diagonal size = (0.4556 
´ projection distance) + 2.8981
Computer type Formats Resolutions
IBM PC and 
IBM PC compatibleEGA, VGA EGA
VGA CGA
VGA60, VESA
VGA Text
VGA Text
SVGA
XGA
SXGA
SXGA
SXGA640 ´ 350
640 ´ 400
640 ´ 480
720 ´ 350
720 ´ 400
800 ´ 600
1024 ´ 768
1152 ´ 864
1280 ´ 960
1280 ´ 1024
Apple Macintosh Standard 8- and 
24-bit color monitor640 ´ 480
832 ´ 624
1024 ´ 768
1152 ´ 870
TV NTSC,
PAL, SECAM640 ´ 480
768 ´ 618 
						

							EPSON PowerLite 5300/7200/7300 Projector
1/99 EPSON PowerLite 5300/7200/7300 Projector - 3
To determine the projection distance when you know the 
diagonal size of the screen image:
oInches:
Maximum projection distance = (2.1949 ´ diagonal size) - 2.5044
Minimum projection distance = (1.6328 
´ diagonal size) - 2.4923
oCentimeters:
Maximum projection distance = (2.1949 ´ diagonal size) - 6.3612
Minimum projection distance = (1.6328 
´ diagonal size) - 6.3304
For example, here are the measurements for three installations:
* For an image size of 300 inches, the projector may be up to 54 feet 
away from the screen, depending on the setting of the zoom ring.
Long Throw Zoom Lens Calculations
If you are using the optional long throw zoom lens, use the 
following formulas instead:
To determine the minimum and maximum diagonal size of an 
image when you know the projection distance:
oInches:
Maximum diagonal size = (0.4742 ´ projection distance) + 3.2489
Minimum diagonal size = (0.2849 
´ projection distance) + 1.8968
oCentimeters:
Maximum diagonal size = (1.2045 ´ projection distance) + 8.2521
Minimum diagonal size = (0.7236 
´ projection distance) + 4.8179
To determine the projection distance when you know the 
diagonal size of the screen image:
oInches:
Maximum projection distance = (3.5094 ´ diagonal size) - 6.6568
Minimum projection distance = (2.1090 
´ diagonal size) - 6.8519
oCentimeters:
Maximum projection distance = (8.9139 ´ diagonal size) - 16.9083
Minimum projection distance = (5.3569 ´ diagonal size) - 17.4038 
Projector Status Lights
The status lights on top of the projector tell you the 
projector’s operating status.
Caution: A red light warns you if a serious problem occurs. 
Power Light
Projection Lamp Light
Temperature Light
Image size 
(diagonal)Horizontal distance from projector 
to screen
Minimum Maximum
300 inches* (762 cm) 487.3 inches (12.4 m) 656.0 inches (16.7 m)
200 inches (508 cm) 324.1 inches (8.2 m) 436.5 inches (11.1 m)
100 inches (254 cm) 160.8 inches (4.1 m) 217.1 inches (5.5 m)
Light status Meaning
Steady orange  Sleep mode. (The projector is plugged in, but not 
projecting.)
Steady green  Power and lamp are on.
Flashing green  The projector is warming up. Allow about 30 seconds.
Flashing orange The projector is cooling down.
Off The power cord is not plugged in or there is an internal 
projector problem.
Light status Meaning
Orange and 
red flashing 
alternatelyLamp timer has exceeded 1900 hours. Projection lamp 
needs replacing.
Steady red Projection lamp has burned out. Replace lamp.
Flashing red Problem with projection lamp or lamp power supply.
Off Lamp is functioning normally.
Light status Meaning
Flashing orange Projector is too hot.
Steady red Projector has turned off automatically because of 
overheating.
Flashing red Problem with the cooling fan or temperature sensor, 
generating an overheat condition.
Off The projector is functioning normally.
power lighttemperature light
projection lamp light 
						

							EPSON PowerLite 5300/7200/7300 Projector
4 - EPSON PowerLite 5300/7200/7300 Projector1/99
Using the Remote Control  
The remote control uses a line-of-sight infrared signal. To use 
the remote control, point it towards one of the infrared  
receivers located at the front and back of the projector. You 
can use the remote control up to about 32 feet (10 meters) 
from the projector. (This distance may be shorter if the remote 
control batteries are low.) You must also be within a 
± 30° 
angle from the front or rear receiver.
Note: The projector may not respond to remote control commands 
in these conditions: ambient light is too bright; a certain type of 
fluorescent light is present; a strong light source (such as direct 
sunlight) shines into the infrared receiver; or other equipment 
emitting infrared energy is present (such as a radiant room 
heater). Correct these conditions to use the remote control or 
control the projector from a computer.
This table summarizes the functions on the remote control.   
Using the Control Panel  
You can use the control panel to control the projector instead 
of the remote control. However, you can program and access 
the custom features only with the remote control. The 
following table summarizes the functions on the control panel.   
Button Function
Menu Displays or hides the menu.
Source Switches between Computer 1 and Computer 2, and 
from video to computer. (When the Computer 2 BNC 
switch on the back of the projector is set to BNC, the 
source is switched to 5BNC.)
Pointer button Use the pointer button to navigate the menus or use the 
remote as a mouse pointer when the projector is 
connected to the computer with the main cable and the  
mouse cable.
Effects buttons Use to display special effects assigned using the ELP 
Link III software.
Top 
multi-purpose 
buttonActs as a right mouse click, registers a menu selection, 
and selects other custom functions.
Bottom 
multi-purpose 
buttonActs as a left mouse click, registers a menu selection, 
and selects other custom functions.
Blank Clears the screen and switches to a blue or black 
display, or a user logo.
bottom 
multi-purpose 
button top 
multi-purpose 
button pointer 
buttonResize Switches the display dot mode and resize mode for VGA, 
SVGA, XGA, and SXGA input (for resolutions that do not 
match the projector’s output).
Custom Accesses Custom menu functions (Zoom, Preview, and 
Strobe).
Freeze Keeps the current computer or video image on the 
screen.
Mute Turns off audio.
 – Volume +
 Adjusts the volume.
Power Starts or stops the projector.
Button Function
Power Starts or stops projection.
Source Switches between Computer 1 and Computer 2, and 
from video to computer. (When the Computer 2 BNC 
switch on the back of the projector is set to BNC, the 
source is switched to 5BNC.)
Menu Displays or hides the menu.
Up, down arrows 
(Sync+/Sync
-)Synchronizes the computer’s graphic signal. 
Use these buttons to adjust an image that is fuzzy or 
streaked, or to select menu items.
Left, right arrows
(Tracking
-/
Tracking+)Matches the projector’s internal clock to various 
computer graphic signals (tracking adjustment).  
Use these buttons to adjust an image with vertical 
fuzzy lines, or to change numeric settings.
Enter Executes a menu selection.
Resize Switches the display dot mode and resize mode for 
VGA, SVGA, XGA, and SXGA input (for resolutions 
that do not match the projector’s output).
Mute Turns off audio.
 – Volume +
 Adjusts the volume.
Blank Clears the screen and switches to a blue or black 
display, or a user logo.
Button Function
Enter button 
						

							EPSON PowerLite 5300/7200/7300 Projector
1/99 EPSON PowerLite 5300/7200/7300 Projector - 5
Computer 1 and 2 and Computer Out 
Connector Pin Assignments
The Computer 1 and 2 and Computer Out connectors are 
female video RGB, 15-pin micro-D-style connectors. The pin 
assignments are:
Cleaning the Air Filter  
Clean the air filter at the bottom of the projector after every 
100 hours of use. If it is not cleaned periodically, it can 
become clogged with dust, preventing proper ventilation. This 
can cause overheating and damage the projector. To clean the 
air filter, follow these steps:
1. Turn off the projector and unplug the power cable.
2. Turn the projector on its side so that the handle is on top 
and you can access the filter easily.
Note: Standing the projector with the handle at the top keeps 
dust from getting inside the projector housing.3. Pull up on the filter cover tab to release the filter cover. 
Remove the cover.
4. The filter is attached to the inside of the filter cover. It is 
recommended that you use a small vacuum cleaner designed 
for computers and other office equipment to clean the filter. 
If you don’t have one, use a dry, lint-free cloth.  
If the dirt is difficult to remove or the filter is torn, replace it.
5. Replace the filter cover when you’re done. Insert the tabs, 
then press down.
Replacing the Lamp   
The projector lamp typically lasts for about 2000 hours of use. 
It is time to replace the lamp when:
oThe projected image gets darker or starts to deteriorate.
oThe projection lamp indicator is either red, or flashing 
orange and red alternately. 
oThe message LAMP REPLACE appears on the screen when 
the projector lamp comes on. 
Warning:  Let the lamp cool before replacing it. Also, do not 
touch the glass portion of the lamp assembly. Touching the glass 
portion of the lamp will result in premature lamp failure.
1. Turn off the projector and unplug the power cable.
2. Turn the projector over so you can access the lamp cover.
Input 
pinComputer Out
connector signalsComputer 1 and 2 
connector signals
1 Red out / red video Red video
2 Green out / green video Green video
3 Blue out / blue video Blue video
4 Reserved Monitor (ID bit 2)
5GND GND
6 GND Red video GND
7 GND Green video GND
8 GND Blue video GND
9 Reserved +5 V
10 GND Synchronous GND
11 Reserved Monitor (ID bit 0)
12 Reserved SDA
13 Horizontal sync Horizontal sync
14 Vertical sync  Vertical sync
15 Vertical sync Reserved 
						

							EPSON PowerLite 5300/7200/7300 Projector
6 - EPSON PowerLite 5300/7200/7300 Projector1/99 3. Use a screwdriver, coin, or similar object to loosen the two 
retaining screws on the lamp cover. When the screws are 
loose, lift off the lamp cover. (You cannot remove these 
screws from the cover.
)
4. Use a screwdriver, coin, or similar object to loosen the two 
screws holding the lamp unit in position. (You cannot 
remove these screws.) 
5. Lift up the handle and pull out the lamp unit.
6. Gently insert the new lamp unit by lowering it into position. 
Make sure it’s inserted securely. Tighten the screws on the 
new lamp unit.
7. Replace the lamp cover and tighten the cover screws. (Make 
sure the lamp cover is securely fastened. The projector turns 
itself off if the lamp cover is open.)
Information Reference List
Engineering Change Notices
None.
Technical Information Bulletins
None.
Product Support Bulletins
None.
Related Documentation
CPD 7925
7541655EPSON PowerLite 5300/7200/7300 
User’s Guide
CPD 7926 EPSON PowerLite 5300/7200/7300 
Portable Guide
SM-ELP5300 EPSON PowerLite 5300 Multimedia 
Projector Service Manual
SM-ELP7273 EPSON PowerLite 7200/7300 Multimedia 
Projector Service Manual
PL-ELP5300 EPSON PowerLite 5300 Multimedia 
Projector Parts Price List 
PL-ELP7200 EPSON PowerLite 7200 Multimedia 
Projector Parts Price List 
PL-ELP7300 EPSON PowerLite 7300 Multimedia 
Projector Parts Price List