Home > Epson > Projector > Epson Powerlite 715c Quick Setup Manual

Epson Powerlite 715c Quick Setup Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson Powerlite 715c Quick Setup Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							STA
    R
    T
    HERE
    EPSON
    ®
    PowerLite
    ®
    505c/715c
    Quick Setup
    Connect the power cord to your projector and plug the other end into a grounded outlet.
    The     power light turns orange.
    3
    Connect the other end to your laptop’s video or      monitor
    port. If you can’t connect the cable to your PowerBook®, you
    may need to use an adapter. See your User’s Guide
    for instructions.
    1
    Press the red Powerbutton to turn on the projector. The      power light
    flashes green as the projector warms up, and the projection lamp comes on
    in about 30 seconds.
    2
    If you’re using a laptop, turn it on or restart it. (Windows only: If you see
    this Add New Hardware screen, click Cancel.)
    Turn Over
    To shut the projector down safely, press the red Powerbutton twice. Let the projector
    cool while the     power light flashes orange (about a minute). Once the light stops
    flashing and stays on, it’s safe to unplug the projector.
    Never unplug the projector when the     power light is green or flashing orange.
    Use these instructions to
    set up your projector.
    Plug in your projector
    Turn on your equipment
    Caution:Before unplugging the projector...
    1
    2Make sure your projector and laptop are turned off.
    Connect one end of the computer cable to the
    Computer port on the projector.
    Using a laptop?
    Follow these instructions to connect your laptop to the projector.
    To connect other devices, such as a VCR or desktop PC, see your
    User’s Guide. You’ll need just two cables: the power cord and
    computer cable.
    tab
    power button
    Use the tab to rotate the lens ring, which extends the lens.
    Then squeeze the tabs to remove the lens cap.
    Extend the lenssqueeze here
    Presenting without
    a computer?
    You can use EasyMP™ to run your presentation directly
    from the projector. Follow the instructions below to start
    the projector. Then see the back of this sheet for more help.
    lens cap 
    						
    							Power
    Freeze
    A/V Mute
    E-ZoomR/C ON
    OFF
    3
    15
    24
    Enter
    Esc
    Menu
    Comp 1
    Auto
    P in PResizeVideoHelp
    - Volume +
    Power
    Freeze
    A/V Mute
    E-ZoomR/C ON
    OFF
    3
    15
    24
    Enter
    Esc
    EasyMP
    If you see a blank screen or the No Signal message
    after turning on your laptop, check the following: 
    Make sure the     power light is green and
    not flashing and the lens cover is off.
    Try turning off the laptop and restarting it.
    If you’ve connected a computer and video source, you may need to
    press the Sourcebutton on top of the projector. (Allow a few
    seconds for the projector to sync up after pressing it.)
    Make sure the computer cable is securely connected at both ends. 
    Adjust the image
    1Rotate the focus ring to sharpen the image.
    If You See a Blank Screen
    CPD-11737 EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.
    Copyright © 2001 by Epson America, Inc.
    lens ring
    2
    Rotate the lens ring if you need to reduce or enlarge
    the image. (You can also move the projector closer to
    or farther from the screen.)
    3
    Raise the image as needed. To do this, pull up the blue foot
    release levers and lift the front of the projector. Once the
    image is positioned where you want it, release the levers
    to lock the feet in position.
    4
    If your image looks like      or      , you’ve placed the projector
    off to one side of the screen, at an angle. Move it directly in
    front of the center of the screen, facing the screen squarely.
    5
    If your image looks like      or      , press the + or – side of the
    Keystonebutton on top of the projector to correct the shape
    of the image.
    EPSON PowerLite 505c/715c
    Note:If you see a blank screen          ,
    see the instructions in the box  below. 
    focus ring
    No signal
    No signal
    If you’re using a Windows laptop:
    Hold down the Fnkey on your keyboard and press the function
    key that lets you display on an external monitor. It may have an
    icon such as        , or it may be labelled CRT/LCD. (Allow a few
    seconds for the projector to sync up after pressing it.)
    You might need to use the Display utility in the Control Panel
    to enable both the LCD screen and external monitor port.
    If you’re using a Macintosh:
    1. From the Apple menu, select Control Panels, then click Monitors
    and Sound.
    2. Click the Arrangeicon.
    3. Drag one monitor icon on top of the other. This lets you display
    on the projector screen as well as the LCD screen.
    If this option isn’t available, you may need to select one of the
    Simulscan resolution settings:
    4. Click the Monitoricon.
    5. Select a Simulscanresolution. (Allow a few seconds for the
    projector to sync up after making the selection.)
    Presenting Without A Computer
    EasyMP lets you run your presentation from the projector. Simply
    convert  your PowerPoint
    ®file into a “scenario” with the
    EMP SlideMaker software on your computer. Then download
    your scenario to the projector’s memory card.
    If your scenario is set to autorun, it will start
    when you turn on the projector. You can present
    it with the remote control.
    1. Make sure the remote control has batteries.
    2. Push up the switch on the side of the
    remote control to turn it on.
    Press Enterto display the next slide.
    Press Escto display the previous slide.
    If your scenario is not set to autorun,
    start it by following these steps:
    1. Press the EasyMPbutton on the remote control.
    You see the EasyMP main screen.
    2. Use the Enterbutton on the remote control
    to highlight your scenario (SIT) file.
    3. Press Enter. In a moment, your presentation begins.
    Press Enterto display the next slide.
    Press Escto display the previous slide.
    4. To exit, press the EasyMPbutton on the remote control.
    You see a confirmation message.
    5. Press Enterto exit. You return to the EasyMP main screen.
    See your User’s Guidefor more information about
    presenting without a computer.
    keystone button
    ON/OFF switch 
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson Powerlite 715c Quick Setup Manual