Epson Powerlite 7000 Users Guide

1  •  
Installation
 n  n  n  n  n  n             14
c.
Connect the other end of the PS/2 mouse cable to the mouse port on your laptop.
d.
If your laptop uses a serial mouse, perform steps b and c using the serial mouse cable instead of the PS/2 mouse cable (not shown in the illustration).  
e.
To configure the projector from your laptop using the ELP Link II software 
or to use the Effects buttons on the 
remote control
, connect one end of the serial cable to the serial 
terminal on the square end of...

Connecting to a Computer
n  n  n  n  n  n  n  n 15
3.
Connect the audio cable.  a.
Connect one end of the audio cable to the Audio In 1 jack on the projector. (Use the Audio In 2 jack if you are connecting a second computer).
b.
Connect the other end of the audio cable to your laptop. 
pro-ch1.fm  Page 15  Tuesday, May 13, 1997  2:19 PM 

1  •  
Installation
 n  n  n  n  n  n             16
Connecting to a Desktop Macintosh 
 
Before beginning, turn off the projector and Macintosh if they are on.1.
Connect the video cables.   Note:
 Macintosh computer configurations vary. See your computer 
manual for the location of the ports needed to connect your PowerLite 7000 projector.a.
Connect either end of the video cable to the projector’s Computer In 1 port. (Use the Computer In 2 port if you are connecting a second computer.)
b.
Remove the...

Connecting to a Computer
n  n  n  n  n  n  n  n 17
c.
Connect the small terminal of the Macintosh video adapter to the other end of the video cable.
d.
Disconnect the monitor cable from the video port on the back of the Macintosh and connect the video cable (with Macintosh video adapter attached) to the video port. If a video-out cable was supplied with your Macintosh, connect one end to the video adapter and the other end to the video port on your Macintosh.
e.
If you wish to view or check images on the...

1  •  
Installation
 n  n  n  n  n  n             18
2.
Connect the main cable. The main cable connects the mouse cable (needed to use the remote control as a mouse) and serial cable (needed to use the ELP Link II software) from your 
Macintosh
 to 
the projector.   a.
Connect the small end of the main cable to the projector’s Mouse/Com 1 port. (Use the Mouse/Com 2 to connect a second computer.)
b.
Connect the MAC mouse cable to the mouse terminal on the other end of the main cable.
main cableMAC mouse...

Connecting to a Computer
n  n  n  n  n  n  n  n 19
c.
Disconnect the mouse cable from the ADB port of the Macin-tosh and connect the mouse connector of the MAC mouse cable to the mouse port.
d.
If you are planning to use the ELP Link II software, connect either end of the serial cable to the serial terminal on the large end of the main cable. Connect the other end of the serial cable to the PRINTER or MODEM port on the back of your Macintosh.
e.
Tighten the screws on both connectors.
3.
Connect the audio...

1  •  
Installation
 n  n  n  n  n  n             20
Connecting to a PowerBook 
  
Your PowerBook must have a video-out capability in order to connect to the PowerLite 7000 projector. Before beginning, turn off the projector and computer if they are on.1.
Connect the video cable. Note:
 PowerBook configurations vary. See your computer manual for 
the location of the ports needed to connect your PowerLite 7000 projector.a.
Connect one end of the video cable to the projector’s Computer In 1 port. (Use the...

Connecting to a Computer
n  n  n  n  n  n  n  n 21
b.
Remove the small cover and set the 
DIP switches on the 
Macintosh video adapter in accordance with the resolutions you want to use (such as 16 inch mode).
c.
Connect the small terminal of the Macintosh video adapter to the other end of the video cable.
d.
Connect one end of the video-out cable that came with your PowerBook to the video-out connector on the back of the PowerBook.
e.
Connect the other end of the PowerBook video-out cable to the...

1  •  
Installation
 n  n  n  n  n  n             22
2.
Connect the main cable. The main cable connects the mouse cable (needed to use the remote control as a mouse) and serial cable (needed to use the ELP Link II software) to the projector.  a.
Connect the small end of the main cable to the projector’s Mouse/Com 1 port. (Use the Mouse/Com 2 port if you are connecting a second computer.)
b.
Connect the MAC mouse cable to the mouse terminal on the other end of the main cable.
c.
Connect the mouse...

Connecting to a Computer
n  n  n  n  n  n  n  n 23
d.
If you are planning to use the ELP Link II software, connect either end of the serial cable to the serial terminal on the large end of the main cable. Connect the other end of the serial cable to the PRINTER or MODEM port on the back of your PowerBook.
e.
Tighten the screws on all connectors to make sure they are fas-tened securely.
4.
Connect the audio cable. a.
Connect one end of the audio cable to the Audio In 1 jack on the projector. (Use the...