Epson Powerlite 600p Multimedia Projector Users Guide

							Maintaining and Transporting the Projector65
Follow these steps to replace the lamp:
1. Turn off the projector, wait for it to cool down (when the light 
stops flashing), then unplug the power cord.
2. Allow the projector to cool for at least half an hour (if it has been 
on).
3. Use a screwdriver to slide the latch and pop open the lamp cover. 
Then lift up and remove it.
4. Use a screwdriver to loosen the two silver screws holding the lamp 
in place. (You can’t remove these screws.)
warning
Let the lamp cool before 
replacing it. If the lamp 
breaks, handle the shards 
carefully to avoid injury.
600-811-820.book  Page 65  Tuesday, April 30, 2002  10:17 AM 
						

							66Maintaining and Transporting the Projector5. Grasp the lamp as shown and pull it straight out.
6. Gently insert the new lamp.
7. Once the lamp is fully inserted, tighten its screws.
8. To replace the lamp cover, insert the tabs and then snap the cover 
into place. (The projector won’t come on if the lamp cover is 
loose.)
caution
Do not touch the glass 
portion of the lamp assembly. 
Touching the glass could 
result in premature lamp 
failure.
600-811-820.book  Page 66  Tuesday, April 30, 2002  10:17 AM 
						

							Maintaining and Transporting the Projector67
Resetting the Lamp Timer
After you replace the lamp, you need to reset the lamp timer using the 
projector’s menu. 
1. Press the 
Menu button on the control panel or the remote 
control. You see the main menu.
2. Use the 
Sync– button (control panel) or the   button (remote 
control) to highlight 
About.
You see the lamp usage hours and other settings.
3. Press 
 to select Reset Lamp Timer. Press  again. You see this 
prompt:
4. Select
 Yes, then press  .
5. When you’re finished, press 
Esc or Menu. 
600-811-820.book  Page 67  Tuesday, April 30, 2002  10:17 AM 
						

							68Maintaining and Transporting the Projector
Transporting the Projector
The projector contains many glass and precision parts. If you need to 
transport it, follow these packing guidelines to prevent damage
to the projector:

When shipping the projector for repairs, use the original 
packaging material if possible. If you do not have the original 
packaging, use equivalent materials, placing plenty of cushioning 
around the projector.

When transporting the projector a long distance, first put it in a 
carrying case (such as an optional EPSON case), then pack it in a 
firm box, using cushioning around the case.

If you want to store the remote control inside the projector’s 
carrying case, be sure to turn it off using the switch on its side. 
This prevents the batteries from discharging if something presses 
against one of the buttons.

When you are hand-carrying the projector, use the carrying 
handle.
note
EPSON shall not be liable 
for any damages incurred 
during transportation.
carrying handle
600-811-820.book  Page 68  Tuesday, April 30, 2002  10:17 AM 
						

							6
Solving Problems69
6
Solving Problems
This chapter helps you solve problems with your projector, and tells 
you how to contact technical support for problems you can’t solve 
yourself. This chapter explains the following:

Using the projector’s on-screen help system

What to do when the projector’s status lights flash

Solving problems with the image or sound

Solving problems with the remote control

Contacting technical support
600-811-820.book  Page 69  Tuesday, April 30, 2002  10:17 AM 
						

							70Solving Problems
Using On-Screen Help
If the image doesn’t look right or your audio isn’t working, you can 
get help by pressing the blue 
? Help button on top of the projector or 
on the remote control. The following choices are available:

Help for the image

Help for the sound

Language selection (Language)
Follow these steps to get help:
1. Press the blue 
? Help button on the projector or the remote 
control. 
You see the Help menu:
2. Press the   
Sync+ or   Sync– button on the projector (or 
use the   button on the remote control) to highlight one of the 
options. Then press the   button to select it.
3. Press the   
Tracking– or  Tracking+ button on the projector 
(or use the   button on the remote control) to highlight the 
problem you want to solve. Then press the   button to view the 
solution(s). 
Esc
Menu
Comp1
Source
Video
S-Video
Comp2/YCbCr
HelpPowe r
Menu EscHelp
Computer/YCbCrVideo
control panel remote control
doesnt
600-811-820.book  Page 70  Tuesday, April 30, 2002  10:17 AM 
						

							Solving Problems71
4. Highlight a solution (if this choice is available). Then press the   
button to select the solution. 
Press the 
Esc button if you need to back up.
If the solution is to adjust one of the settings, press either 
the  
Tracking– or  Tracking+ button on the projector (or 
use the   button on the remote control) to adjust it.
5. To exit the Help system, press the blue
 ? Help button.
If none of the suggestions solves your problem, see additional 
solutions to problems in the following sections.
What To Do When the Lights Flash
The lights on top of the projector indicate the projector’s status and 
let you know when a problem occurs.
If the projector is not working correctly, first turn it off, let it cool, 
and unplug it. Then plug the power cord back in and turn on the 
projector. If this does not solve the problem, check the status lights on 
top of the projector and try the solutions recommended on the 
following pages.
power lightlamp light temperature 
light
600-811-820.book  Page 71  Tuesday, April 30, 2002  10:17 AM 
						

							72Solving ProblemsRefer to the following table for a complete description of the 
projector’s status lights and their meaning:
Status lights
Light Status Description
orange The projector is in sleep mode. You can unplug it or press the Power 
button to turn it on.
flashing green The projector is warming up. Wait for the image to appear.
green The projector is operating normally.
flashing orange The projector is cooling down. You can’t turn it back on (and you should 
not unplug it) until the light stops flashing and remains orange. 
flashing red Power is cut off because of an internal problem. Remove the power cord 
and contact EPSON for help.
red The lamp is burned out. Replace it as described on page 64.
flashing orange The lamp is almost burned out. Make sure you have a replacement lamp 
ready.
flashing red There is a problem with the lamp, power supply, fan, or circuit. If 
necessary, replace the lamp as described on page 64.
flashing orange The projector is too hot. Make sure the temperature surrounding the 
projector does not exceed 95 
°F (35 °C) and there is plenty of space 
around and under the projector for ventilation. 
The air filter may be clogged. Clean or replace it as described on page 63. 
red The projector is overheating, which turns the lamp off automatically. Wait 
until the cooling fan stops, then unplug the power cord. Plug the power 
cord back in and press the 
Power button. Make sure the room 
temperature is not above 95 °F (35 °C) and there is plenty of space 
around and under the projector for ventilation. 
The air filter may be clogged. Clean or replace it as described on page 63.
If the projector continues to overheat after you clean the air filter, the 
problem may be caused by damage to the cooling fan or temperature 
sensor. Contact EPSON for help.
Warning:
 Except as specifically explained in this User’s Guide, do not 
attempt to service this product yourself.
flashing red There is a problem with the cooling fan or temperature sensor. Turn off 
the projector and unplug it. Contact EPSON for help.
600-811-820.book  Page 72  Tuesday, April 30, 2002  10:17 AM 
						

							Solving Problems73
The   power light is flashing orange and you cannot turn 
on the projector.
The lamp is cooling down. Wait until the light turns off and then 
press the 
Power button to turn on the projector.
The   power light does not come on.
Make sure the power cord is connected securely both at the power 
outlet and the projector. If you have just replaced the lamp, make sure 
the cover is securely fastened.
Solving Problems with the 
Image or Sound
No image appears on the screen.

Check that the 
 
P power light is green, not flashing, and the lens 
cap is off. 

The projector may be in sleep mode. If the 
 
P power light is 
orange, press the 
Power button to turn the projector on.

If the power was switched off and then on again, the projector 
may still be cooling down. Wait until the power light stops 
flashing and remains orange; then press the 
Power button again.

Try pressing the Power button on the remote control.

Make sure the Brightness setting on the Video menu is correct. 
See page 48 for more information. Try selecting the 
Reset All 
setting to return all setup menus to their default values. 

Press the A/V Mute button to make sure the picture has not been 
turned off temporarily. 

The attached computer may be in sleep mode or displaying a 
black screen saver. Try pressing a key on the computer.
600-811-820.book  Page 73  Tuesday, April 30, 2002  10:17 AM 
						

							74Solving Problems
You see a blue screen with the message No Signal displayed.

Make sure the cables are connected correctly, as described in 
Chapter 1.

Try restarting your computer.

If you’ve connected a computer and one or more video sources, 
you may need to press the 
Computer/YCbCr or Video button 
(on the projector) or the 
Comp1, Comp2/YCbCr, Video, or 
S-Video
 button (on the remote control) to select the correct 
source. Allow a few seconds for the projector to sync up after 
pressing the button.
If you’re using a PC laptop:

Hold down the Fn key and press the function key that lets you 
display on an external monitor. It may have an icon such as 
, or it may be labelled 
CRT/LCD. Allow a few seconds for 
the projector to sync up after pressing it. Check your laptop’s 
manual or online help for details. 
On most systems, the   key lets you toggle between the LCD 
screen and the projector, or display on both at the same time.

Depending on your computer’s video card, you might need to use 
the Display utility in the Control Panel to make sure that both the 
LCD screen and external monitor port are enabled. See your 
computer’s documentation or online help for details.
If you’re using a PowerBook or iBook with OS 9.x:
1. From the Apple menu, select 
Control Panels, then click 
Monitors and Sound
.
2. Click the 
Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display 
on the projector screen as well as the LCD screen.
4. If this option isn’t available, click the 
Monitor icon. 
5. Select one of the listed 
Simulscan resolutions. (Allow a few 
seconds for the projector to sync up after making the selection.)
600-811-820.book  Page 74  Tuesday, April 30, 2002  10:17 AM