Epson Powerlite 53c Multimedia Projector Users Guide

							Setting Up the Projector15
2. Connect the other end of the audio cable to your laptop’s
 headphone jack or   audio-out jack. (Jack locations vary; see 
your computer manual if you’re not sure which jack to use.)
If you don’t need to make any other connections, you can plug in 
your projector and turn it on. See page 20 for instructions.
Connecting to Video Sources
You can connect a DVD player, VCR, camcorder, laser disc player, 
digital camera, gaming console—such as Microsoft Xbox, Sony 
PlayStation 2, or Nintendo GameCube—or any other compatible 
video source to your projector.
The projector supports HDTV, NTSC, PAL, and SECAM, and 
automatically detects the video format.
The projector can receive composite video, S-Video, and component 
video. The type of cable you use depends on the video source: 
■For composite video, use the RCA A/V cable included with the 
projector.
■For component video, you will need the optional EPSON 
component video cable (ELPKC19).
■For S-Video, use the S-Video cable supplied with your video 
device or obtain one from you electronics dealer.
Follow the instructions below for your type of connection.
note
The projector does not 
support TV antenna cable 
F connectors. 
						

							16Setting Up the Projector
Connecting the RCA Video Cable
Before starting, make sure the projector and your DVD player or 
other video source are turned off. 
1. Connect one end of the yellow RCA plug to the projector’s 
Video 
jack.
2. Connect the other end of the plug to the video-out jack on your 
video source.
3. Connect the red and white plugs on the RCA A/V cable to the 
projector’s 
Audio2 L (white) and R (red) jacks.
4. Connect the red and white plugs on the other end of the cable to 
the corresponding audio output jacks on your video source. 
						

							Setting Up the Projector17
Connecting an S-Video Cable
If your video source has an S-Video jack, you can use it to project a 
higher quality video image. However, you’ll need an S-Video cable, 
which may be included with your video source, or may be purchased.
Before starting, make sure the projector and your DVD player or 
other video source are turned off.
1. Insert one end of an S-Video cable into the projector’s 
S-Video 
port.
2. Insert the other end into the S-Video output port of your video 
source.
3. Connect the audio plugs on the RCA A/V cable as described on 
page 16. 
						

							18Setting Up the Projector
Connecting a Component Video Cable
If your video source has component video connectors, you can use 
them to project a higher quality video image. However, you’ll need a 
component video cable, which can be purchased from EPSON 
(ELPKC19).
Before starting, make sure the projector and your DVD player or 
other video device are turned off.
1. Connect the large end of the component video cable to the 
projector’s 
Computer/Component Video port. 
2. Insert the three ends of the component video cable into the 
R, G, 
and 
B ports on your video source.
3. Connect the audio plugs on the RCA A/V cable as described on 
page 16.
4. After you turn on the projector, use the Video menu to set the 
Input Signal to 
YCbCr or YPbPr. See page 40 for more 
information. 
						

							Using the Projector19
1
Using the Projector
Once you’ve set up the projector, you’re ready to turn it on, adjust 
the image, and give your presentation. 
Although you can operate the projector without it, the remote control 
lets you use additional features. See Chapter 3 for instructions on 
using the remote. This chapter covers the following:
■Turning on the projector and other equipment
■Adjusting the image
■Shutting down the projector 
						

							20Using the Projector
Turning On Your Equipment
Make sure your projector and other equipment are set up and 
connected correctly, as described in Chapter 1 or Appendix A. Then 
turn on your projector, as described below, followed by any 
equipment you’ve connected to it. You can turn on your computer 
and video equipment in any order, but if you have both a computer 
and video source connected, you may have to switch to the desired 
source as described on page 21. 
Turning On the Projector
Follow these steps to plug in and turn on the projector:
1. Remove the lens cap.
2. Connect one end of the power cord to the projector’s power inlet. 
3. Connect the other end to an electrical outlet. 
The power light on top of the projector turns orange, indicating 
that the projector is receiving power but not yet turned on. Wait 
until the light stops flashing, but stays lit orange.
caution
Do not use the projector with 
the lens cap in place. The 
heat generated by the lamp 
can damage the cap. 
						

							Using the Projector21
4. Press the P Power button on top of the projector or on the 
remote control. 
The power light flashes green as the projector warms up, and the 
projection lamp comes on in about 40 seconds. The power light 
stays green. 
5. Do one of the following:
■If you’re using a computer, turn it on or restart it. In a few 
moments, you should see your computer display projected. 
(Windows
® only: If you see a message saying that it has found 
a plug-and-play monitor, click 
Cancel.) 
■If you’re projecting a video, press the Source button on top 
of the projector or the 
S-Video/Video button on the remote 
control to switch to your video source. Then press the 
Play 
button on your DVD player or other device.
If a projected image fails to appear, see the next section for help. 
Once you see your image, turn to page 25 for instructions on focusing 
and making other image adjustments. 
When you’re done with your presentation, shut down the projector as 
described on page 29. Shutting down the projector correctly prevents 
premature lamp failure and possible damage from overheating. 
Color Mode Computer
MenuA/V Mute
E-ZoomFreeze
S-Video/Video
Page up Page downPower
ESC AutoEnter
Remote control Projector
warning
Never look into the lens when 
the lamp is on. This can 
damage your eyes, and is 
especially dangerous for 
children. 
						

							22Using the Projector
What To Do If You See a Blank Screen
If you see a blank screen or a blue screen with the message No Signal 
after turning on your computer or video source, try the following:
■Make sure the cables are connected correctly, as described in 
Chapter 1 (for laptops and video sources) or in Appendix A (for 
desktop computers and other sources).
■Make sure the power light is green and not flashing and the lens 
cover is off. 
■Try restarting your computer.
■Press the Source button on top of the projector to select the 
correct source. (Allow a few seconds for the projector to sync up 
after pressing the button.)
If you’re using a PC laptop:
■Hold down the Fn key and press the function key that lets you 
display on an external monitor. It may have an icon such as   
or it may be labelled 
CRT/LCD. Allow a few seconds for the 
projector to sync up after pressing it. Check your laptop’s manual 
or online help for details. 
On most systems, the   or 
CRT/LCD key lets you toggle 
between the LCD screen and the projector, or display on both at 
the same time. 
■Depending on your computer’s video card, you might need to use 
the Display utility in the Control Panel to make sure that both the 
LCD screen and external monitor port are enabled. See your 
computer’s documentation or online help for details. 
						

							Using the Projector23
If you’re using a Macintosh laptop with OS 9.x or 
earlier:
You may need to set up your system to display on the projector screen 
as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
Control Panels, then click 
Monitors or Monitors and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. 
If the 
Arrange option isn’t available, you may need to select one of 
the Simulscan resolution settings:
1. Click the 
Monitor icon, if necessary. 
2. Select a 
Simulscan resolution as shown. (Allow a few seconds for 
the projector to sync up after making the selection.)
Click here
Drag one 
monitor icon on 
top of the other
Click here
Select a 
Simulscan 
resolution 
						

							24Using the Projector
If you’re using a Macintosh laptop with OS X:
You may need to set up your system to display on the projector screen 
as well as the LCD screen. Follow these steps:
1. From the Apple menu, select 
System Preferences, then click 
Displays.
2. Select VGA Display or Color LCD, click Arrange or 
Arrangement, and make sure Mirror Displays is checked.
Click here
Select Mirror 
Displays