Epson Monitor V4.30 User Manual

Using the control functions
31
Using the control functionsCarrying out control using control buttons
Click the icon of a projector to be controlled in Grouping view or Detail 
list view, and click a control button to enable control of only that selected 
projector.
You can also enable control of all selected projectors by selecting more 
than one projector in Grouping view or Detail list view and clicking a 
control button. The methods of selecting more than one projector at the 
same time are as...

Using the control functions
32
The following table shows the meanings of the control buttons.
* If the button does not function, you can switch the input source using the 
EasyMP control button.•Some connected projectors may not be equipped with all of the above 
ports or functions. If you click a button for a port or function that is not 
available, nothing will happen.
•You can select objects to be controlled and use the control buttons to 
carry out control operations even when the following are being...

Using the control functions
33
You can select projectors and right-click on them to select Web control 
even when the following are being displayed.
Group properties sp.28
Warning and Error Projector list (Control operations can only be carried 
out for projectors with a warning status.) sp.27
Carrying out control using timer settings
This is useful for carrying out certain control operations such as turning 
a projector's power on and off at specified times every day or every week.
Timer settings...

Using the control functions
34
Procedures for new timer settings
ProcedureA
Click "Add" on the timer setting window. The following 
window is displayed and the new timer settings are applied.
At Operation, you can carry out the operations of turning the pow-
er on and off and switching the input sources, similarly for the con-
trol buttons on the main window. If you set the input source 
switching, the projector's power will turn on at the timer start time 
even if it is not on at the time....

E-mail notification function settings
35
E-mail notification function settings
The mail notification function can be used to send corresponding 
notification messages to a preset e-mail address when a projector that is 
connected to the network assumes a certain status, or if it experiences a 
problem or warning. By using this function, the operator can be notified 
of a projector’s status or problems even when the operator is in a 
different location from the projectors.
•Up to three addressees...

E-mail notification function settings
36
C
Click "Notification event" and check the items for mail 
notification in the window that appears.
D
Click "OK".
The Set mail notification function window appears again.
Repeat Steps 3 and 4 to set the notification events to be notified.
E
When the setup is complete, click "OK". 

E-mail notification of problem/warning/status
37
E-mail notification of problem/warning/status
If the projector experiences a problem or enters a status requiring 
attention, an e-mail like that shown below is sent to the address specified 
for Recipient mail address.
If there is more than one problem, warning, or status, the corresponding 
messages are output to separate lines.The details contained in the e-mail message can consist of the following.
Item
Details shown
E-mail subject [Display name...

E-mail notification of problem/warning/status
38
Messages to inform that the projector has recovered from the error or 
warning statuses are sent.Other error Stop using the projector, disconnect the power 
cable from the electrical outlet, and contact 
Epson.sProjector's User's Guide Supply System Error 
(Ballast)
Auto Iris Error
Network error (TCP 
connection error)Check that the projector's power is turned on and 
the LAN cable is connected, and also check that 
Network Monitoring is set to...

Application lock function
39
Application lock function
You can use the application lock to prevent third parties from operating 
the projectors using EMP Monitor and from changing settings without 
authority. Opening and closing EMP Monitor and status monitoring can 
still be carried out even when the application lock is applied.
In addition, when a password has been set, the password must be entered 
in order to cancel the application lock. This ensures that the application 
lock can not be easily...

40
Appendix