Epson Aculaser M1200 User Manual

❏Be careful not to scratch the surface of the drum. When you remove the photoconductor unit
from the printer, always place the unit on a clean, smooth surface. Avoid touching the drum,
since oils from your skin can permanently damage its surface and affect print quality.
❏To get the best print quality, do not store the photoconductor unit in an area subject to direct
sunlight, dust, salt air, or corrosive gases (such as ammonia). Avoid locations subject to
extreme or rapid changes in temperature or...

❏Connect your printer to an electrical outlet that meets the power requirements of this printer.
Your printer’s power requirements are indicated on a label attached to the printer. If you are
not sure of the power supply specifications in your area, contact your local power company or
consult your dealer.
❏If you are unable to insert the AC plug into the electrical outlet, contact an electrician.
❏If damage occurs to the plug, replace the cord set or consult a qualified electrician. If there are
fuses in...

❏Unplug this printer from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into it.
C. If it has been exposed to rain or water.
D. If it does not operate normally when the operating instructions are followed.
Adjust only those controls that are covered by the operating instructions since
improper adjustment of other controls may result in damage and will often
require...

Laser safety labels
w
 Warning:
The performance of procedures and adjustments other than those specified in this guide may
result in hazardous radiation exposure.
Your printer is a Class 1 laser product as defined in the IEC 60825-1:2001 specifications.
The label shown on the right is attached to the back of the printer in countries where required.
Internal laser radiation
Max. Average Radiation Power 36.903 μW at laser aperture of the print head unit
Wavelength 770 to 800 nm
This is a Class III b Laser...

Minimize the risk
To minimize the risk of exposure to ozone, you should avoid the following conditions:
❏Use of multiple laser printers in a confined area
❏Operation in conditions of extremely low humidity
❏Poor room ventilation
❏Long, continuous printing together with any of the above
Printer location
The printer should be located so that the exhaust gases and heat generated are:
❏Not blown directly into the user’s face
❏Vented directly out of the building whenever possible
Power On/Off Cautions
c...

Chapter 1
Product Information
Printer Parts
Front view
EPL-6200
ab
c
d
e
f g
EPSON AcuLaser M1200 Series     User’s Guide
Product Information     16
 

AcuLaser M1200/EPL-6200L
ab
c
d
e g
a. Output cover
b. Output tray
c. Control panel
d. Front cover
e. MP (Multi-Purpose) tray
f. Manual feed slot (EPL-6200 only)
g. Power switch
Rear view
EPL-6200
a
b
c de g
EPSON AcuLaser M1200 Series     User’s Guide
Product Information     17
 

EPL-6200 Network model
a
b
c df g
AcuLaser M1200/EPL-6200L
a
b
d
a. AC inlet
b. USB interface connector
c. Duplex Unit connector (EPL-6200 only)
d. Parallel interface connector
e. Type B interface slot (EPL-6200 only)
f. Ethernet interface connector (EPL-6200 Network model only)
g. Right side cover (EPL-6200 only)
Control Panel
The EPL-6200 has six indicator lights and three buttons, while the AcuLaser M1200/EPL-6200L
comes with two indicator lights. The indicator lights inform you of basic printer...

Indicator lights
EPL-6200
abc
d
e f
AcuLaser M1200/EPL-6200L
e d
aMemoryUsually turns on or flashes in combination with other lights to indicate a
memory-related error or warning.
bTonerOn when the printer’s developer cartridge has run out of toner. Flashes
to indicate that toner is running low. If this light is flashing, have a new
developer cartridge ready.
cPaperTurns on or flashes, and when in combination with the Error light,
usually indicates a paper-related problem. On usually indicates a paper...

fDataOn when data is received and stored in the print buffer (the section of
memory reserved for receiving data) but not yet printed. Flashing
indicates that the printer is processing data. When no data remains in
the print buffer, this light is off.
Consumable Products
To purchase consumable products, contact your dealer or a qualified service representative in your
area.
Consumable products
Developer Cartridge (0520/0521/0522/0523)
This cartridge includes the toner that is used to create the image on...