Epson AcuLaser CX11NFT User Manual

Loading Paper11
5. Slide the cassette back in.
Note: 
After loading paper, press the Setup button on the control panel, press the 
rbutton to select Printer Settings, press the d button to select Tray Menu, and 
match the LC Tray Size and LC Type settings (Lower Cassette) with the loaded 
paper size.
Removing Printouts From the Output Tray
The output tray is located on the top of cover B and can hold up to 250 sheets. Since 
printouts are output face-down, this tray is also referred to as the face-down...

12Handling Paper and Originals
Selecting Your Paper Source
You can specify a paper source manually or set up automatic paper source detection 
(recommended). 
■To manually select a paper source for Windows, access the printer driver 
properties, click the 
Basic Settings tab, and select the paper source that you 
want to use from the Paper Source list. Then click 
OK. (For details see page 19.)
■To manually select a paper source for Macintosh®, access the printer driver, select 
Printer Settings from the...

Selecting a Paper Tray13
MP Tray
The MP tray can hold the following types and sizes of paper. 
Paper typePaper sizeCapacity
Plain paper  A4, A5, B5, Letter (LT), 
Government Letter (GLT), Half 
Letter (HLT), Legal (LGL), 
Government Legal (GLG), F4, 
Executive (EXE)
Custom-size paper: 
3.54 in. × 4.33 in. (minimum) to
8.66 in. × 14 in. (maximum)Up to 180 sheets
(Total stack thickness: 0.8 in.)
Semi-thick paper  A4, A5, B5, Letter (LT), 
Government Letter (GLT), 
Half Letter (HLT), Legal (LGL),...

14Handling Paper and Originals
Paper Cassette Unit 
The optional Paper Cassette Unit can hold the following types and sizes of paper. 
Placing Originals for Copying and Scanning
You can place originals on either the document table or the Auto Document Feeder 
(CX11NF only), depending on the type of the original. 
Note: 
If you place originals on both the Auto Document Feeder and the document table, only 
the documents in the Auto Document Feeder are scanned.Coated paper  A4, A5, B5, Letter (LT),...

Placing Originals for Copying and Scanning15
Placing Originals on the Document Table
Before scanning or copying, make sure the transportation lock on the left side of the 
document table is set to the   unlock position. Always keep the document table 
clean. 
1. Open the document cover and place your original face-down on the glass as 
shown, in the upper left corner. Move your original about 0.06 in. (1.5 mm) away 
from the top and left edges so all of it will be scanned. 
If you plan to scan multiple...

16Handling Paper and Originals
Placing Large or Thick Originals (CX11N Only)
When you scan large or thick originals, you can remove the document cover. Just 
open it and pull it straight up.
If you need to press the document flat while you copy or scan it, do not press too hard 
and be careful not to move it.
Caution: 
Do not use excessive force on the document cover, and do not twist it diagonally. 
You may damage the document cover.
When you are done, replace the document cover by inserting the tabs...

Placing Originals for Copying and Scanning17
Placing Originals in the Auto Document Feeder 
(CX11NF Only)
The ADF can hold the following types and sizes of paper. 
1. Slide the edge guides all the way outward.
2. Arrange your originals so the page you want scanned or copied first is on the top 
of the stack.
Note: 
Pages are fed from the top and ejected face-down.
3. Insert up to 50 originals short edge first and face-up in the Auto Document 
Feeder until it meets resistance. Slide the edge guides inward...

18Handling Paper and Originals
 

Printing19
Printing3
You can print documents using Windows or Macintosh OS X 10.2.4 to 10.4.x. This 
chapter tells you how to select print settings, print, and monitor your print job. 
Printing in Windows
See these sections for instructions on selecting printer settings in Windows:
■“Printing From an Application” below
■“Customizing Windows Print Settings” on page 21
Printing From an Application 
After you create a document in a software program, follow these steps to print it using 
the basic printer...

20Printing
2. Make sure EPSON AL-CX11 Advanced is selected. 
3. Click the 
Properties or Preferences button. (If you see a Setup, Printer, or 
Options button, click it. Then click Properties or Preferences on the next 
screen.)
You see the Basic Settings window: 
4. Make sure 
Automatic is selected. 
5. Select from these 
Print Quality options:
■Draft: For rough drafts with reduced print quality
■Text: For text-only documents with higher text quality
■Text&Image: For documents with text and images with...