Epson AcuLaser C4200DN User Manual
Here you can view all the pages of manual Epson AcuLaser C4200DN User Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 231
Using the Control Panel231 7 7 7 7 7 7 7 7 7 7 7 7 Clear Warning Clears warning messages that show errors except for these that occur from consumable products or mandatory-replacement parts. Clear All Warnings Clears all warning messages that appear on the LCD panel. Reset Stops printing and clears the current job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully. Reset All Stops...
Page 232
232Using the Control Panel Parallel I/F Allows you to activate or deactivate the parallel interface. Speed Specifies the pulse width of the ACKNLG signal when receiving data in the Compatibility mode or Nibble mode. When Fast is selected, the pulse width is about 1 ms. When Normal is selected, the pulse width is about 10 ms. Bi-D Allows you to specify the bidirectional communication mode. When you select Off, bidirectional communication is disabled. Buffer Size Determines the amount of memory to...
Page 233
Using the Control Panel233 7 7 7 7 7 7 7 7 7 7 7 7 USB Menu These settings control communication between the printer and the computer when using the USB interface.
Page 234
234Using the Control Panel *1After this item is changed, the setting value takes effect after a warm boot or after the power is turned on again. While it is reflected in the Status Sheet and EJL read-back, the actual change takes effect after a warm boot or after the power is turned on again. *2Available only when a USB external device with D4 support is connected. The USB Config setting is set to No automatically when exiting the panel settings. *3Available only when a USB external device with...
Page 235
Using the Control Panel235 7 7 7 7 7 7 7 7 7 7 7 7 USB SPEED Allows you to select the operation mode of USB interface. Selecting HS is recommended. Select FS if HS does not work on your computer system. Buffer Size Determines the amount of memory to be used for receiving data and printing data. If Maximum is selected, more memory is allocated for receiving data. If set to Minimum is selected, more memory is allocated for printing data. Note: ❏ To activate Buffer Size settings, you must turn off...
Page 236
236Using the Control Panel *1Available only when downloaded fonts are available. *2Available only when the optional font ROM module is installed. *3Depending on the font that has been selected. *4 Depending on whether Letter (60) or A4 (64) paper has been selected. FontSource Sets the default font source. Font Number Sets the default font number for the default font source. The available number depends on the settings you made. Item Settings (default in bold) FontSourceResident, Download *1, ROM A*2...
Page 237
Using the Control Panel237 7 7 7 7 7 7 7 7 7 7 7 7 Pitch Specifies the default font pitch if the font is scalable and of fixed-pitch. You can select from 0.44 to 99.99 cpi (characters per inch), in 0.01-cpi increments. This item may not appear depending on the Font Source or Font Number settings. Height Specifies the default font height if the font is scalable and proportional. You can select from 4.00 to 999.75 points, in 0.25-point increments. This item may not appear depending on the Font...
Page 238
238Using the Control Panel Changes the assignment for the paper source select command. When 4 is selected, the commands are set as compatible with the HP LaserJet 4. When 4K is selected, the commands are set as compatible with the HP LaserJet 4000, 5000, and 8000. When 5S is selected, the commands are set as compatible with the HP LaserJet 5S. PS3 Menu N ew :PostScript s tandardThis menu allows you to make settings which affect the printer when it is in the PS3 mode. Error Sheet When you...
Page 239
Using the Control Panel239 7 7 7 7 7 7 7 7 7 7 7 7 Specifies the data format. Select On for the Binary data and select Off for the ASCII data. Note: ❏ Binary can only be used with network connection. ❏ You do not have to select On when using AppleTalk. To use the Binary data, make sure your application supports Binary data and that SEND CTRL-D Before Each Job and SEND CTRL-D After Each Job are set to No. When this setting is set to On, you cannot use TBCP (Tagged binary communication protocol)...
Page 240
240Using the Control Panel * Depending on whether Letter (62) or A4 (66) paper has been selected. Font Selects the font. Pitch Item Settings (default in bold) FontCourier, Prestige, Roman, Sans Serif, Roman T, Orator S, Sans H, Script, OCR A, OCR B Pitch 10, 12, 15 cpi, Prop. Condensed Off, On T. Margin 0.40 ... 0.50 ... 1.50 inches in 0.05-inch increments Text 1... 62/66*... 132 lines CGTable PcUSA, Italic, PcMultilin, PcPortugue, PcCanFrenc, PcNordic, PcTurkish2, PcIcelandic, PcE.Europe,...