Epson AcuLaser C2600DTN User Manual

Using the Control Panel261
7
7
7
7
7
7
7
7
7
7
7
7
Adjust the density of the printing for back side of normal paper. 
The setting becomes darker as the value increases.
Thick
Adjust the density for thick paper. The setting becomes darker as 
the value increases.
Trnsprnc
Adjust the density for transparencies. The setting becomes darker 
as the value increases.
Envelope
Adjust the density for envelopes. The setting becomes darker as 
the value increases.
Highland
Prevents printing defects caused by...

262Using the Control Panel Feed Offset2
Adjust the vertical position in which to star printing. The position 
moves lower on the sheet as the value increases. This setting is 
used when printing the printing on the backside of paper for 
duplex printing.
Scan Offset2
Adjust the horizontal position in which to start printing. The 
position moves to the right of the sheet as the value increases. This 
setting is used when printing on the backside of paper for duplex 
printing.
Status and Error Messages...

Using the Control Panel263
7
7
7
7
7
7
7
7
7
7
7
7
The printer is canceling all print jobs in the printer memory, 
including jobs the printer is currently receiving or printing. This 
message appears when the +Cancel Job button has been 
pressed down for more than 2 seconds.
Cancel Print Job
The printer is canceling the current print job. This message 
appears when the +Cancel Job button has been pressed and 
released within 2 seconds.
Cancel Print Job (by host)
The print job is canceled at the printer...

264Using the Control Panel Check Paper Size
The paper size setting is different from the size of paper loaded 
in the printer. Check to see if the correct size of paper is loaded in 
the specified paper source.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. See  How to access the control panel menus on page 
223 for instructions.
Check Paper Type
The media loaded in the printer does not match the paper type 
setting in the printer driver. Media that matches only the paper...

Using the Control Panel265
7
7
7
7
7
7
7
7
7
7
7
7
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. For instruction about accessing the control panel 
menus, see  How to access the control panel menus on page 223.
Color Data Received
The printer receives color printing data when it is in the B/W or 
4 × B/W mode. Press the NStart/Stop button to print the data in 
monochrome, or press the +Cancel Job button to cancel the 
print job.
Cooling Down
The printer lowers its...

266Using the Control Panel Unable to store form overlay data on the printer’s optional Hard 
Disk Drive. Either the drive is full, or the maximum number of 
form overlay files has been reached. Delete any form overlay files 
you no longer need, then try storing the new overlay again.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. For instruction about accessing the control panel 
menus, see  How to access the control panel menus on page 223.
Form Feed
The printer is...

Using the Control Panel267
7
7
7
7
7
7
7
7
7
7
7
7
There is insufficient memory to print the page at the specified 
print quality. The printer automatically lowers the print quality 
s o  t h a t  i t  c a n  c o n t i n u e  p r i n t i n g .  I f  t h e  q u a l i t y  o f  t h e  p r i n t o u t  i s  n o t  
acceptable, try simplifying the page by limiting the number of 
graphics or reducing the number and size of fonts.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu....

268Using the Control Panel If a photoconductor unit is already installed, confirm cover D is 
closed. Otherwise, turn off the printer, open cover D. Remove the 
photoconductor unit, then reinstall it properly. Close cover D. The 
error clears automatically if the photoconductor unit is properly 
installed. 
Install uuuu TnrCart
The indicated toner cartridges are not installed in the printer. (The 
letters C, M, Y, or K appear in place of uuuu and indicate the colors 
Cyan, Magenta, Yellow, and Black...

Using the Control Panel269
7
7
7
7
7
7
7
7
7
7
7
7
Invalid N/W Module
There is no network program, or the network program cannot be 
used with your printer. Contact a qualified service representative.
Invalid P5C
The optional P5C Emulation Kit is installed, but the printer is in 
the B/W mode or 4 × B/W mode. When you use the optional P5C 
Emulation Kit, make sure that the printer is in the Color mode. 
Invalid PS3
The PostScript3 ROM module is broken. Turn off the printer and 
contact your dealer....

270Using the Control Panel Menus Locked
This message appears if you try to change the printer’s settings 
through the control panel when the buttons are locked. You can 
unlock them by using the Network utility. Refer to the Network 
Guide for information.
Need Memory
The printer has insufficient memory to complete the current print 
job. 
To clear this error message, select Clear Warning from the control 
panel’s Reset Menu. See How to access the control panel menus 
on page 223 for instructions.
To...