Epson AcuLaser C2600DN User Manual

Using the Control Panel231
7
7
7
7
7
7
7
7
7
7
7
7
*1Default paper sizes are automatically detected.
*2Custom-size paper: 98 × 148 minimum, 216 × 297 maximum.
*3Available only when the optional Duplex Unit is installed.
Page Size
Specifies the paper size.
Wide A4
Selecting On decreases the left and right margins from 4 mm to 
3.4 mm.
Orientation
Specifies whether the page is printed in portrait or landscape 
orientation.
Resolution
Item Settings (default in bold)
Page Size
*1A4*1, A5, B5, LT*1, HLT, GLT,...

232Using the Control Panel Specifies the printing resolution.
RITech
Turning RITech on produces smoother and crisper lines, text, and 
graphics.
Toner Save
When this setting is selected in the B/W and 4 × B/W modes, the 
printer saves toner by substituting a gray shade for the black 
inside of characters. The characters are outlined in full black on 
the right and lower edges.
When this setting is selected in the Color mode, the printer saves 
toner by using half the normal amount of toner.
Image...

Using the Control Panel233
7
7
7
7
7
7
7
7
7
7
7
7
c
Caution:
Make sure that the printed image does not extend beyond the edge 
of the paper. Otherwise, you may damage the printer.
Top Offset B
Adjusts the vertical printing position on the back of the paper 
when printing on both sides. Use this if the printout on the back 
is not where you expected.
Left Offset B
Adjusts the horizontal printing position on the back of the paper 
when printing on both sides. Use this if the printout on the back 
is not...

234Using the Control Panel
*1Available only when the corresponding option is installed.
*2Available only for PCL5e, ESC/Page, ESC/P2, FX, or I239X mode.
Lang
Specifies the language displayed on the LCD panel and that 
printed on the status sheet.
Time Out
Item Settings (default in bold)
LangEnglish, Français, Deutsch, Italiano, 
ESPAÑOL, SVENSKA, Dansk, Nederlands., 
SUOMI, Português,  , 
Time Out 0, 5 to 60 to 300 in increments of 1
Paper SourceAuto, MP, LC1, LC2
*1
MP ModeNormal, Last
Manual FeedOff,...

Using the Control Panel235
7
7
7
7
7
7
7
7
7
7
7
7
Specifies the length of the time, in seconds, before a time out when 
interfaces are being switched automatically. The time before a 
time out occurs is the length of time from the point when no data 
is being received from an interface until the point of switching the 
interface. If the printer has a print job when switching the 
interface, the printer prints the print job.
Paper Source
Specifies whether paper feeds into the printer from the MP tray 
or...

236Using the Control Panel Turns duplex printing on or off.
Binding
Specifies the binding direction of the printout.
Start Page
Specifies whether printing starts from the front or back of the 
page.
Paper Type
Specifies the type of paper to be used for printing. The printer 
adjusts the printing speed according to this setting. The printing 
speed is reduced when Thick or Trnsprnc is selected.
Page Side
Select Front when printing on the front of thick paper (Thick).
Select Back when printing on the back...

Using the Control Panel237
7
7
7
7
7
7
7
7
7
7
7
7
If you want to ignore a paper size error, select On. When you turn 
this item on, the printer keeps printing even if the image size 
exceeds the printable area for the specified paper size. This may 
cause smudges because of the toner that is not transferred onto 
the paper properly. When this item is turned off, the printer stops 
printing if a paper size error occurs.
Auto Cont
When you turn this setting on, the printer automatically continues...

238Using the Control Panel Note:
If this item is set to Continue, the print result may be different from 
what you expected because there may not be enough toner to print the 
data.
LCD Contrast
Adjusts the contrast of the LCD panel. Use the uUp and dDown 
buttons to set the contrast between 0 (lowest contrast) and 15 
(highest contrast.)
Mode Config. Menu
This menu allows you to switch the printing mode. You can also 
use this menu to stop using one of the black toner cartridges when 
the printer is in...

Using the Control Panel239
7
7
7
7
7
7
7
7
7
7
7
7
Switches to the B/W mode, which is the monochrome printing 
mode with only one black toner cartridge installed.
Change mode 4 × B/W
Switches to the 4 × B/W mode, which is the monochrome printing 
mode with four black toner cartridges installed.
Change mode Color
Switches to the Color mode, which is the color printing mode with 
the C, M, and Y toner cartridges installed.
KC/KM/KY/KK Toner
This setting is available only when the printer is in the 4 × B/W...

240Using the Control Panel Stops printing and clears the current job received from the active 
interface. You may want to reset the printer when there is a 
problem with the print job itself and the printer cannot print 
successfully.
Reset All
Stops printing, clears the printer memory, and restores the printer 
settings to their default values. The print jobs received from all 
interfaces are erased.
Note:
Performing Reset All clears print jobs received from all interfaces. Be 
careful not to interrupt...