Epson AcuLaser 2600DTN User Manual
Here you can view all the pages of manual Epson AcuLaser 2600DTN User Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 231
Using the Control Panel231 7 7 7 7 7 7 7 7 7 7 7 7 *1Default paper sizes are automatically detected. *2Custom-size paper: 98 × 148 minimum, 216 × 297 maximum. *3Available only when the optional Duplex Unit is installed. Page Size Specifies the paper size. Wide A4 Selecting On decreases the left and right margins from 4 mm to 3.4 mm. Orientation Specifies whether the page is printed in portrait or landscape orientation. Resolution Item Settings (default in bold) Page Size *1A4*1, A5, B5, LT*1, HLT, GLT,...
Page 232
232Using the Control Panel Specifies the printing resolution. RITech Turning RITech on produces smoother and crisper lines, text, and graphics. Toner Save When this setting is selected in the B/W and 4 × B/W modes, the printer saves toner by substituting a gray shade for the black inside of characters. The characters are outlined in full black on the right and lower edges. When this setting is selected in the Color mode, the printer saves toner by using half the normal amount of toner. Image...
Page 233
Using the Control Panel233 7 7 7 7 7 7 7 7 7 7 7 7 c Caution: Make sure that the printed image does not extend beyond the edge of the paper. Otherwise, you may damage the printer. Top Offset B Adjusts the vertical printing position on the back of the paper when printing on both sides. Use this if the printout on the back is not where you expected. Left Offset B Adjusts the horizontal printing position on the back of the paper when printing on both sides. Use this if the printout on the back is not...
Page 234
234Using the Control Panel *1Available only when the corresponding option is installed. *2Available only for PCL5e, ESC/Page, ESC/P2, FX, or I239X mode. Lang Specifies the language displayed on the LCD panel and that printed on the status sheet. Time Out Item Settings (default in bold) LangEnglish, Français, Deutsch, Italiano, ESPAÑOL, SVENSKA, Dansk, Nederlands., SUOMI, Português, , Time Out 0, 5 to 60 to 300 in increments of 1 Paper SourceAuto, MP, LC1, LC2 *1 MP ModeNormal, Last Manual FeedOff,...
Page 235
Using the Control Panel235 7 7 7 7 7 7 7 7 7 7 7 7 Specifies the length of the time, in seconds, before a time out when interfaces are being switched automatically. The time before a time out occurs is the length of time from the point when no data is being received from an interface until the point of switching the interface. If the printer has a print job when switching the interface, the printer prints the print job. Paper Source Specifies whether paper feeds into the printer from the MP tray or...
Page 236
236Using the Control Panel Turns duplex printing on or off. Binding Specifies the binding direction of the printout. Start Page Specifies whether printing starts from the front or back of the page. Paper Type Specifies the type of paper to be used for printing. The printer adjusts the printing speed according to this setting. The printing speed is reduced when Thick or Trnsprnc is selected. Page Side Select Front when printing on the front of thick paper (Thick). Select Back when printing on the back...
Page 237
Using the Control Panel237 7 7 7 7 7 7 7 7 7 7 7 7 If you want to ignore a paper size error, select On. When you turn this item on, the printer keeps printing even if the image size exceeds the printable area for the specified paper size. This may cause smudges because of the toner that is not transferred onto the paper properly. When this item is turned off, the printer stops printing if a paper size error occurs. Auto Cont When you turn this setting on, the printer automatically continues...
Page 238
238Using the Control Panel Note: If this item is set to Continue, the print result may be different from what you expected because there may not be enough toner to print the data. LCD Contrast Adjusts the contrast of the LCD panel. Use the uUp and dDown buttons to set the contrast between 0 (lowest contrast) and 15 (highest contrast.) Mode Config. Menu This menu allows you to switch the printing mode. You can also use this menu to stop using one of the black toner cartridges when the printer is in...
Page 239
Using the Control Panel239 7 7 7 7 7 7 7 7 7 7 7 7 Switches to the B/W mode, which is the monochrome printing mode with only one black toner cartridge installed. Change mode 4 × B/W Switches to the 4 × B/W mode, which is the monochrome printing mode with four black toner cartridges installed. Change mode Color Switches to the Color mode, which is the color printing mode with the C, M, and Y toner cartridges installed. KC/KM/KY/KK Toner This setting is available only when the printer is in the 4 × B/W...
Page 240
240Using the Control Panel Stops printing and clears the current job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully. Reset All Stops printing, clears the printer memory, and restores the printer settings to their default values. The print jobs received from all interfaces are erased. Note: Performing Reset All clears print jobs received from all interfaces. Be careful not to interrupt...