Epson 1761 W Manual

							The  following  optional  accessories  and  consumables  are  available.  Please
purchase  these  products  as  and  when  needed.  The  following  list  of  optional
accessories  and  consumables  is  current  as  of:  February  2012.  Details  of
accessories  are  subject  to  change  without  notice  and  availability  may  vary
depending  on  the  country  of  purchase.
Optional  Accessories
50"  portable  screen      ELPSC32A  compact  screen  that  can  be  carried  easily.  (aspect  ratio  4:3)60"  portable  screen      ELPSC27
80"  portable  screen      ELPSC28
100"  screen      ELPSC29Portable  roll-type  screens.  (aspect  ratio  4:3)70"  portable  screen      ELPSC23
80"  portable  screen      ELPSC24
90"  portable  screen      ELPSC25Portable  roll-type  screens.  (aspect  ratio  16:10)53"  portable  screen      ELPSC30
64"  portable  screen      ELPSC31Portable  magnetic  screens.  (aspect  ratio  4:3)Multi-aspect  screen    ELPSC26A  portable  multi-aspect  screen.Computer  cable  ELPK C02
(1.8  m  -  for  mini  D-Sub15-pin/mini  D-Sub  15pin)This  is  the  same  as  the  computer  cable  supplied  with  the  projector.
Computer  cable  ELPKC09
(3  m  -  for  mini  D-Sub15-pin/mini  D-Sub  15pin)
Computer  cable  ELPKC10
(20  m  -  for  mini  D-Sub15-pin/mini  D-Sub  15pin)Use  one  of  these  longer  cables  if  the  computer  cable  supplied  with  the  projector
is  too  short.Component  video  cable  ELPK C19
(3  m  -  for  mini  D-Sub  15-pin/RCA  male
^3)
Use to connect a 
component
 video
g source.
Interactive  unit  ELPIU01Use  when  operating  the  computer  screen  on  the  projection  surface.Document  camera  ELPDC06/ELPDC11Use  when  projecting  images  such  as  books,  OHP  documents,  or  slides.Wireless  LAN  unit  ELPAP07  (EB-1771W/EB-1761W  only)Use  when  connecting  the  projector  to  a  computer  wirelessly  and  projecting.Quick  Wireless  Connection  USB  Key  ELPAP09  (EB-1776W/
EB-1771W/EB-1761W  only)Use  when  you  want  to  quickly  establish  one-to-one  connection  between  the
projector  and  a  computer  with  Windows  installed.Ceiling  pipe  (450  mm)
* ELPFP13
Ceiling  pipe  (700  mm)* ELPFP14
Use  when  installing  the  projector  on  a  high  ceiling.Ceiling  mount
* ELPMB23
Use when installing the projector on a ceiling.Attachment  plate
* ELPPT01
Use  when  attaching  the  ceiling  mount  to  the  projector.*Special  expertise  is  required  to  suspend  the  projector  from  a  ceiling.  Contact
your  local  dealer  or  the  nearest  address  provided  in  the  Epson  Projector
Contact  List.
s Epson  Projector  Contact  List
Optional Accessories and Consumables
121 
						

							Consumables
Lamp unit   ELPLP65Use as a replacement for used lamps.Air filter   ELPAF31Use as a replacement for used air filters.
Optional Accessories and Consumables
122 
						

							Changing  Settings  Using  a  Web  Browser  (Web  
Control)
By  using  the  Web  browser  of  a  computer  connected  to  the  projector  on  a
network,  you  can  make  settings  and  control  the  projector.  This  function
allows  you  to  perform  setup  and  control  operations  remotely.  In  addition,
since you can use the computer's keyboard,  entering  characters  required  for
the  setup  is  easier.
Use Microsoft Internet Explorer 6.0 or later as the Web browser. If using a
Mac  OS  X,  use  Safari.a
If  you  set  Standby  Mode to  Communication  On,  you  can  use  the
Web  browser  to  make  settings  and  perform  control  even  if  the
projector  is  in  standby  mode  (when  the  power  is  off).
s Extended - Standby  Mode p.84
Projector  setup
In  the  Web  browser,  you  can  set  items  that  are  usually  set  in  the  projector's
Configuration  menu.  The  settings  are  reflected  in  the  Configuration  menu.
There  are  also  items  that  can  only  be  set  in  the  Web  browser.
Items  in  the  Configuration  menu  that  cannot  be  set  by  the  Web  browser
•Settings  Menu  -  Pointer  Shape
•Settings  Menu  -  Test  Pattern
•Settings  Menu  -  User  Button
•Extended  Menu  -  User's  Logo
•Extended  Menu  -  Language
•Extended  Menu  -  Operation  -  High  Altitude  Mode
•Extended  Menu  -  Operation  -  Lens  Cover  Timer
•Reset  Menu  -  Reset  All  and  Reset  Lamp  HoursThe  settings  for  items  on  each  menu  are  the  same  as  the  projector's
Configuration  menu.
s
 "Configuration  Menu"  p.75
Items  that  can  only  be  set  with  a  Web  browser
•SNMP  Community  Name  (up  to  32  single-byte  alphanumeric  characters)
•Monitor  Password  (up  to  16  single-byte  alphanumeric  characters)
Displaying  the  Web  Control  screen
Use  the  following  procedure  to  display  the  Web  Control  screen.
Make  sure  the  computer  and  projector  are  connected  to  the  network.  When
communicating  with  a  wireless  LAN,  connect  in  Advanced  mode.a
If  your  Web  browser  is  set  up  to  connect  via  a  proxy  server,  the  Web
Control  screen  cannot  be  displayed.  To  display  Web  Control,  you  need
to  make  settings  so  that  a  proxy  server  is  not  used  for  a  connection.
a
Start  the  Web  browser  on  the  computer.
b
Enter  the  IP  address  of  the  projector  in  the  address  input  box  of
the  Web  browser,  and  press  the  Enter  key  on  the  computer's
keyboard.
The  Web  Control  screen  is  displayed.
When  Web  Control  Password  is  set  from  the  Configuration  menu,
the  password  entry  screen  is  displayed.
c
Enter  the  user  ID  and  password.
Enter  "EPSONWEB"  as  the  user  ID.
The  default  password  is  "admin".
Monitoring and Controlling (EB-1776W/EB-1771W/EB-1761W Only)
123 
						

							a
•Enter  the  user  ID  even  if  the  password  setting  is  disabled.
You  cannot  change  the  user  ID.
•You  can  change  the  password  in  Network  menu  from  the
Configuration  menu.
s Network - Basic - Web  Control  Password p.88
Displaying  the  Web  Remote  screen
The  Web  Remote  function  allows  you  to  perform  projector  remote  control
operations  with  a  Web  browser.a
Display  the  Web  Control  screen.
b
Click  Web  Remote.
c
The  Web  Remote  screen  is  displayed.
Name Function
A
[t] buttonTurns the projector power on or off.
s "From Installation to Projection" p.29
B
[Computer] buttonChanges to images from the Computer port.
C
[Video] buttonEach time the button is pressed, the image displayed
changes between the Video input port and HDMI input
port.
D
[Freeze] buttonImages are paused or unpaused.
s "Freezing the Image (Freeze)" p.61
E
[A/V Mute] buttonTurns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.60
Monitoring and Controlling (EB-1776W/EB-1771W/EB-1761W Only)
124 
						

							Name Function
F
[Page] buttons
[
[][
]]Changes pages in files such as PowerPoint files when using
the following projection methods.
•When using the Wireless Mouse function
s "Using  the  Remote  Control  to  Operate  the
Mouse  Pointer  (Wireless  Mouse)"  p.64
•When using USB Display
s "Projecting  with  USB  Display"  p.31
•During a network connection (EB-1776W/EB-1771W/
EB-1761W only)
When projecting images or scenarios using Slideshow,
pressing these buttons displays the previous/next screen.
G
[Source Search]
buttonChanges to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.30
H
[LAN] buttonChanges to the image projected with EasyMP Network
Projection. When projecting using the supplied or
optional Quick Wireless Connection USB Key, this button
switches to that image. (EB-1776W/EB-1771W/
EB-1761W only)
s "Switching to the Target Image by Remote Control"
p.31
I
[USB] buttonEach time the button is pressed, it cycles through the
following images:
•USB Display
•Images from the device connected to the USB port
s "Switching to the Target Image by Remote Control"
p.31
J
[Volume] buttons
[a][b][a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.42
Using  the  Mail  Notification  Function  to  Report  
Problems
When  you  set  Mail  Notification,  notification  messages  are  sent  to  the  preset
email  addresses  when  a  problem  or  warning  occurs  with  a  projector.  This
will  enable  the  operator  to  be  notified  of  problems  with  projectors  even  at
locations  away  from  the  projectors.s
 Network - Mail - Mail  Notification p.91a
•Up  to  a  maximum  of  three  notification  destinations  (addresses)  can
be  registered,  and  notification  messages  can  be  sent  to  all  three
destinations  at  once.
•If  a  projector  develops  a  critical  problem  and  suddenly  stops
working,  it  may  not  be  able  to  send  a  message  notifying  an  operator
of  the  problem.
•If  you  set  Standby  Mode to  Communication  On,  you  can  control
the  projector  even  if  it  is  in  standby  mode  (when  the  power  is
off).
s Extended - Standby  Mode p.84
Reading  Error  Notification  Mail
When  the  Mail  Notification  function  is set  to  On  and  a  problem  or  warning
occurs  in  the  projector,  the  following  email  will  be  sent.
Mail  sender:  Address  for  Address  1
Subject:  EPSON  Projector
Line  1:  The  projector  name  where  the  problem  has  occurred
Line  2:  The  IP  address  set  for  the  projector  where  the  problem  has
occurred.
Line  3  and  on:  Details  of  the  problem
Monitoring and Controlling (EB-1776W/EB-1771W/EB-1761W Only)
125 
						

							The  details  of  the  problem  are  listed  line  by  line.  The  messages  are  listed
below.
•Internal  error
•Fan  related  error
•Sensor  error
•Lamp  timer  failure
•Lamp  out
•Internal  temperature  error
•High-speed  cooling  in  progress
•Lamp  replacement  notification
•No-signal
No  Signal  is  input  to  the  projector.  Check  the  connection  status  or  check
that  the  power  for  the  signal  source  is  turned  on.
•Auto  Iris  Error
•Power  Err.  (Ballast)
See  the  following  to  deal  with  problems  or  warnings.s
 "Reading  the  Indicators"  p.98
Management  Using  SNMP
By  setting  SNMP to  On in  the  Configuration  menu,  notification  messages
are  sent  to  the  specified  computer  when  a  problem  or  warning  occurs.  This
will  enable  the  operator  to  be  notified  of  problems  with  projectors  even  at
locations  away  from  the  projectors.s
 Network - Others - SNMP p.92
a
•SNMP  should  be  managed  by  a  network  administrator  or  someone
who  is  familiar  with  the  network.
•To  use  the  SNMP  function  to  monitor  the  projector,  you  need  to
install  the  SNMP  manager  program  on  your  computer.
•The  managing  function  using  SNMP  cannot  be  used  via  wireless
LAN  in  Quick  connection  mode.
•Up  to  two  destination  IP  addresses  can  be  saved.
ESC/VP21  Commands
You  can  monitor  and  control  the  projector  from  a  computer  via  USB.
Connect  the  device  and  the  projector  with  a  USB  cable,  and  then  enter  the
communication  commands  (ESC/VP21  commands).
Before  starting
To  control  and  monitor  the  projector  using  ESC/VP21  commands,  the
following  preparations  must  be  carried  out.a
Install  the  USB  communication  driver  (EPSON  USB-COM  Driver)  to
your  computer.  For  information  about  the  EPSON  USB-COM  Driver,
contact  your  local  dealer  or  the  nearest  address  provided  in  the
Epson  Projector  Contact  List.s
 Epson  Projector  Contact  List
b
Set  USB  Type  B to  Link  21L from  the  projector's  Configuration
menu.s
 Extended - USB  Type  B p.84
c
Connect  the  computer's  USB  port  to  the  projector's  USB  (TypeB)
port with a USB cable.
Start  from  step  2  from  the  second  time.
Monitoring and Controlling (EB-1776W/EB-1771W/EB-1761W Only)
126 
						

							Command  list
When  the  power  ON  command  is  transmitted  to  the  projector,  the  power
turns  on  and  it  enters  warm-up  mode.  When  the  projector's  power  has
turned  on,  a  colon  ":" (3Ah)  is  returned.
When  a  command  is  input,  the  projector  executes  the  command  and
returns  a  ":",  and  then  accepts  the  next  command.
If  the  command  being  processed  terminates  abnormally,  an  error  message  is
output  and  a  ":"  is  returned.
Item Command
Power  ON/OFF On PWR  ON
Off PWR  OFF
Signal  selection Computer Auto SOURCE  1F
RGB SOURCE  11
Component SOURCE  14
HDMI SOURCE  30
Video SOURCE  41
USB  Display SOURCE  51
USB SOURCE  52
LAN  (EB-1776W/EB-1771W/EB-1761W
only)SOURCE  53
A/V  Mute  On/Off On MUTE  ON
Off MUTE  OFF
A/V  Mute  selection Black MSEL  00
Blue MSEL  01
Logo MSEL  02
Add  a  Carriage  Return  (CR)  code  (0Dh)  to  the  end  of  each  command  and
transmit.
Communications  protocol
•Default  baud  rate  setting:  9600  bps
•Data  length:  8  bit
•Parity:  None
•Stop-bit:  1  bit
•Flow  control:  None
Monitoring and Controlling (EB-1776W/EB-1771W/EB-1761W Only)
127 
						

							Check  the  numbers  and  then  apply  the  following  countermeasures.  If  you  cannot  resolve  the  problem,  contact  your  network  administrator,  or  contact  your  local
dealer  or  the  nearest  address  provided  in  the  Epson  Projector  Contact  List.s
 Epson  Projector  Contact  List
Event ID Cause Remedy
0432
0435Failed to startup EasyMP Network Projection. Restart the projector.
0434
0481
0482
0485Network communication is unstable. Check the network communication status, and reconnect after waiting for a
while.
0433 Cannot play transferred images. Restart EasyMP Network Projection.
0484 Communication was disconnected from the computer.
0483
04FEEasyMP Network Projection ended unexpectedly. Check the network communication status, and then restart the projector.
0479
04FFA system error occurred in the projector. Restart the projector.
0891 Cannot find an access point with the same SSID. Set the computer, the access point, and the projector to the same SSID.
0892 The WPA/WPA2 authentication type does not match. Check that the wireless LAN security settings are correct.
s Security p.90
0893 The WEP/TKIP/AES encryption type does not match.
0894 Communication was disconnected because the projector connected to an
unauthorized access point.Contact your network administrator for more information.
0898 Failed  to acquire DHCP. Check that the DHCP server is operating correctly. If you are not using DHCP,
turn off the DHCP setting.
s Wireless LAN - IP Settings p.89
0899 Other communication errors If restarting the projector or EasyMP Network Projection does not solve the
problem, contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s Epson Projector Contact List
About Event ID (EB-1776W/EB-1771W/EB-1761W Only)
128 
						

							PJLink  Class1  was  established  by  the  JBMIA  (Japan  Business  Machine  and
Information  System  Industries  Association)  as  a  standard  protocol  for
controlling  network-compatible  projector's  as  part  of  their  efforts  to
standardize  projector  control  protocols.
The  projector  complies  with  the  PJLink Class1  standard  established  by  the
JBMIA.
It  complies  with  all  commands  except  for  the  following  commands  defined
by  PJLink  Class1,  and  agreement  was  confirmed  by  the  PJLink  standard
adaptability  verification.
URL:http://pjlink.jbmia.or.jp/english/
•Non-compatible  commands
Function PJLink Command
Mute settings Image muting set AVMT 11
Audio muting set AVMT 21
•Input  names  defined  by  PJLink  and  corresponding  projector  sources
Source PJLink  Command
Computer INPT 11
Video INPT 21
HDMI INPT 32
USB INPT 41
LAN INPT 52
USB Display INPT 53
•Manufacturer  name  displayed  for  "Manufacture  name  information  query"
EPSON
•Model  name  displayed  for  "Product  name  information  query"
EB-1776W/EB-C301MS/PowerLite 1776W
EB-1771W/EB-C301MN/EB-C3011WN/PowerLite 1771W
EB-1761W/EB-C261MN/EB-C3005WN/PowerLite 1761W
About PJLink (EB-1776W/EB-1771W/EB-1761W Only)
129 
						

							Projection  Distance  (For  EB-1776W/EB-1771W/
EB-1761W)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit:  cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
28" 57x43 71 - 85 -4
30" 61x46 76 - 91 -4
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
40" 81x61 102 - 122 -6
50" 100x76 127 - 153 -7
60" 120x91 153 - 184 -8
80" 160x120 205 - 246 -11
100" 200x150 256 - 308 -14
150" 300x230 385 - 462 -21
200" 410x300 514 - 617 -28
250" 500x380 643 - 771 -35
260" 520x400 668 - 802 -36
Unit:  cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 66x37 69 - 83 -2
40" 89x50 92 - 111 -2
50" 110x62 115 - 139 -3
60" 130x75 139 - 167 -3
70" 160x87 162 - 195 -4
80" 180x100 186 - 223 -5
100" 220x120 232 - 279 -6
150" 330x190 349 - 419 -8
200" 440x250 466 - 560 -11
250" 550x310 583 - 700 -14
280" 620x350 653 - 784 -16
Screen Size and Projection Distance
130