Element Electronics ELGFW601 Digital Lcd Tv User Manual
Have a look at the manual Element Electronics ELGFW601 Digital Lcd Tv User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 Element Electronics manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
USB multimedia operation 20 OK Multimedia Operation: Photo Multimedia Operation: Music JPEG
21 Troubleshooting If your television does not operate normally or does not turn on, please check the following troubleshooting questions. Remember to also check the other connected electronic devices, such as DVDs or Blu-ray players to pinpoint any problem. If the television still fails to operate normally, please contact technical support (refer to Warranty page). SYMPTOM POSSIBLE CAUSE REMEDY Dead. No LED lit No power to the TV. Check all connections to the TV’s AC socket. Dead. No LED lit orange Set in standby mode.Press either the Power button or the Standby button on the remote control. Blue screenNo signal. Press INPUT button to select the correct source Incorrect source selected. Noisy, snowy, ghosting picture (TV)Poor antenna signal.If using an indoor antenna, try adjusting the antenna postion. Check antenna connections No sound. F F O ” e t u M “ d n u o s n r u T . ” e t u M “ d n u o S Volume set too low. Check volume settings. External leads not connected “if used”.Check that all external leads are connected properly.
22 Troubleshooting Before contacting the service technician, perform the following simple checks. If any problem still persists, unplug the LCD TV and call for assistance. PROBLEM POSSIBLE SOLUTION No sound and picture - Check that the main plug has been connected to a wall outlet - Check that you have pressed the POWER button on the front of the TV set - Check the picture contrast and the brightness setting Red LED indicator light Set in standby mode. Press either the POWER button or the Standby button on the remote control Normal picture but no sound - Check the volume - Sound muted? Press the MUTE button - Try another channel, the problem may be with the broadcast - Are the audio cables installed properly? The remote control does not work - Check to see if there are any objects between the TV and remote control causing obstruction - Are batteries installed with correct polarity (+ / -) - Correct remote operating mode set: TV, VCR, etc? - Install new batteries Power suddenly turns off - Is the sleep timer set? - Check the power control settings. Power may be interrupted - No broadcast on the station tuned Picture appears slowly after switching on - This is normal, the image is muted during the product start up process. Please contact a service provider if the picture has not appeared after 5 minutes Poor Color or picture - Adjust the color in Menu option - Keep a sufficient distance between the product and the VCR - Try another channel, the problem may be with the broadcast - Are the VIDEO cables installed properly? - Activate any function to restore the brightness of the picture Horizontal/vertical bars or picture shaking - Check for local interference, such as an electrical appliance or power tool Blue Screen - Press INPUT button to select correct source Poor reception on some channels - Station or cable experiencing problems. Tune to another station - Station signal is weak, reorient antenna to receive better reception - Check for sources of possible interference Lines or streaks in pictures - Check the antenna (change the direction of the antenna) No output from one of the speakers - Adjust balance in the Menu option
23 Troubleshooting NOTE: When there is a problem in VGA mode (only when VGA mode is applied) PROBLEM POSSIBLE SOLUTION The signal is out of range - Adjust resolution, horizontal frequency, or vertical frequency - Check whether the signal cable is connected or loose - Check the input source Vertical bar or stripe on background, horizontal noise and incorrect positionSet the auto configure or adjust clock, phase or H/V position Screen Color is unstable or is a single Color - Check the signal cable - Re-install the PC video card Maintenance Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have with your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the screen 1. A great tip to dust off your screen. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use to wipe the screen. 2. Make sure the excess water is off the screen, then let air-dry before you turn on the TV. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your TV dormant for a long time (such as a vacation), it is a good idea to unplug the power cord to protect against possible damages from lightning or power surges.
24 The FCC Wants You To Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving an- tenna; 2) increase the separation between the equipment and the receiver; 3) connect the equip- ment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV technician for additional suggestions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere de- fined to be used with the installation of the product, they must be used in order to ensure com- pliance with FCC regulation. Canadian DOC statement Standard Television Receiving Apparatus Canada BETS-7 This Class B digital apparatus complies with Canadian ICES-003. Specifications y l l a n o g a i d s e h c n i 60 e z i S l e n a P D C L e p y T y a l p s i D T F T y g o l o n h c e T l e n a P z H 120 z H 0 2 1 s v z H 0 6 l e n a P 1080P n o i t u l o s e R y a l p s i D p 0 8 0 1 o t p u e l b i t a p m o C D H 1920 x 1080 n o i t u l o s e R l e n a P 9 : 6 1 o i t a R t c e p s A 5,000:1 l e n a p - Dynamic Contrast Ratio Brightness (Centre Typ.) cd/m2 500 4 ms ) G o t G ( e m i T e s n o p s e R s r u o h 0 0 0 0, 5 ) s r u o H . p y T ( e f i L p m a L Horizontal Viewing Angle (At CR>10) 176 Vertical Viewing Angle (At CR>10) 176
This product contains electrical or electronic materials. The presence of these materials may, if not disposed of properly, have potential adverse effects on the environment and human health. Presence of this label on the product means it should not be disposed of as unsorted waste and must be collected separately. As a consumer, you are responsible for ensuring that this product is disposed of properly. To find out how to properly dispose of this product, please go to www.elementelectronics.com and click on Sustainability. This TV incorporates High-Definition Multimedia Interface (HDMI ) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. TM