Electrolux Ewx 14550 W User Manual

							Washing phase icons
By selecting the wash programme, the
washing programme phase icons
corresponding to the various phases
making up the programme are shown
in the bottom of the display. 
= washing
= rinsing
= draining
= spinning
= drying
After the machine has started, only the
running icon stays on. When the
programme has finished, the flashing
zero (
0.00) is displayed.
Soil level icons
When selecting a programme on the
display appears an icon indicating the
degree of soiling automatically
proposed by the machine.
Child lock
This function allows you to leave the
appliance unsupervised during it’s
functioning.
Door locked light (
9)
The pilot light 
9 illuminates to indicate
that the appliance starts operating and
the door is locked.
This light indicates if the door can be
opened: 


 light off: the door can be opened.
7.4
7.3
7.2
If your laundry is not removed within 10
minutes after the programme is finished,
the backlight of the display switches off
and the energy saving system will be
enabled.
Only the button 
8pilot light is blinking to
indicate that the appliance has to be
switched off.
By pressing any buttons the appliance
will come out from the energy saving
status and you could set another
washing programme or switch off the
appliance.
control panelelectrolux  11
132961190.qxd  01/09/2008  9.00  Page 11
 
						

							before pressing button 8: it will be
impossible to start the machine.
after pressing button 
8: it will be
impossible to change any other
programme or option.
To enable or disable this option press
buttons 
5and 6simultaneously for
about 6 seconds until on the display,
the icon  appears or disappears.
Daily Use
Load the laundry
Open the door by carefully pulling the
door handle outwards. Place the
laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
Measure out the detergent and the
fabric softener
Pull out the dispenser drawer until it
stops. Measure out the amount of
detergent required, pour it into the
main wash compartment  and, if
you wish to carry out the prewash,
pour it into the compartment marked
.

2
1
12electroluxuse
Use
First Use
●Ensure that the electrical and water
connections comply with the
installation instructions.
●Remove the polystyrene block and
any material from the drum.
●Run a cotton cycle at 90° or 95°C,
without any laundry in the machine, to
remove any manufacturing residue
from the drum and tub. Pour 1/2 a
measure of detergent into the main
wash compartment and start the
machine.
Acoustic signals
The machine is provided with an
acoustic device, which sounds in the
following cases:
●at the end of the cycle
●if there is a fault
By pressing buttons 
4and 5
simultaneously for about 6 seconds,
the acoustic signal is deactivated
(except if there is a fault).
By pressing these 2 buttons again, the
the acoustic signal is reactivated.
Child safety lock
This function allows you to leave the
appliance unsupervised and not to
worry that children might be injured by
or cause damage to the appliance.
This function remains able also when
the washing machine is not working.
There are two different ways to set this
option:
132961190.qxd  01/09/2008  9.00  Page 12
 
						

							If required, pour fabric softener into the
compartment marked  (the amount
used must not exceed the “MAX” mark
in the drawer). Close the drawer gently.
Select the required programme by
turning the programme selector
dial (1)
Turn the programme selector dial to
the required programme. 
The light of button 
8starts to flash and
the display shows the duration of the
selected programme.
The selector dial can be turned either
clockwise or anticlockwise. Turn to
position Oto Reset programme/
Switch OFF the machine.
For the description of each of the
washing programmes on the
selector dial, consult the chapter
«Washing programmes».
At the end of the programme the
selector dial must be turned to
position O, to switch the machine
off.
	

	

Attention!
If you turn the programme selector dial
to another programme when the
machine is working, the redlight of
button 
8will blink 3 times and the
message Errwill appear on the display
to indicate a wrong selection. The
machine will not perform the new
selected programme.
Programme Option buttons
Depending on the programme, different
functions can be combined. These
must be selected after choosing the
desired programme and before
pressing the button 
8.
When these buttons are pressed, the
corresponding pilot lights illuminate.
When they are pressed again, the pilot
lights go out.
If an incorrect option is selected, the
integrated red pilot light of the button
8
flashes 3 times and the Errmessage
appears on the display for some
seconds.
For the compatibility among the
washing programmes and the
options see chapter «Washing
Programmes».
Select the temperature by pressing
button 
2
Press this button repeatedly to
increase or decrease the temperature,
if you want your laundry to be washed
at a temperature different from the one
proposed by the washer-dryer.
Select the spin speed, Rinse Hold
or Night Cycle option 
by pressing
button 
3
Press button 3repeatedly to change
the spin speed, if you want your
laundry to be spun at a speed different
from the one proposed by the washer-
useelectrolux  13
132961190.qxd  01/09/2008  9.00  Page 13
 
						

							14electroluxuse
dryer. The relevant light will light up.
When you select a programme, the
machine automatically proposes the
maximum spin speed provided for the
programme.
Rinse Hold:by selecting this option
the water of the last rinse is not
emptied out to prevent the fabrics from
creasing. When the programme has
finished the display shows 
0.00
flashing, the pilot light 9is on, the light
of button 
8is off and the door is
locked to indicate that the water must
be emptied out.
Night Cycle: by selecting this option,
the machine will not drain the water of
the last rinse, so as not to wrinkle the
laundry. As all spinning phases are
suppressed, this washing cycle is very
noiseless and it can be selectionned at
night or in times with a more
economical power rate.
On cotton and synthetic programmes
the rinses will be performed with more
water. 
When the programme has finished the
display shows three blinking
0.00, the
pilot light 
9is on, the light of button 8
is off and the door is locked to indicate
that the water must be emptied out.
To empty the water out, please
read the chapter «At the end of the
programme».
Select the Extra Rinse option by
pressing button 
4
The machine performs some additional
rinses. This option is recommended for
people who are allergic to detergents,
and in areas where the water is very
soft.
Select the Drying Time by pressing
button
5
If you wish to carry out a timed drying
programme, press this button until the
drying time you want appears on the
display according to the fabrics (cot-
tons or synthetics) you have to dry.
For Cottons you can select a drying
time from 10 minutes to 250 minutes
(
4.10). 
For Synthetics you can select a drying
time from 10 minutes to 130 minutes
(
2.10).
Every time you press this button the
drying time increases by 5 mins.
Select the Delay Start by pressing
button 
6
Before you start the programme, if you
wish to delay the start, press button 
6
repeatedly, to select the desired delay.
The relevant light will illuminate.
The selected delay time value (up to 20
hours) will appear on the display for a
few seconds, then the duration of the
programme will appear again.
You must select this option after you
have set the programme and before you
press button 
8.
The door will be locked throughout the
delay time. If you wish to add laundry in
the machine during the delay time press
button 
8to put the machine in pause
and wait until the pilot light 
9 goes out
before opening the door. Add the
laundry, close the door and press the
button 
8again.
You can cancel or modify the delay time
at any moment, before you press
button 
8.
The wash programme can be delayed
from 30 min - 60 min - 90 min, 2 hours
and then by 1 hour up to a maximum of
20 hours by means of this button.
t
e
132961190.qxd  01/09/2008  9.00  Page 14
 
						

							Selecting the delayed start.
 Select the programme and the
required options.
 Select the delay start.
 Press button 
8: the machine starts its
hourly countdown.
The programme will start after the
selected delay has expired.
Cancelling the delayed start after having
started the machine
 Press button 
8.
 Press button 
6once until the symbol
0’is displayed.
 Press button 
8again.
The Delay Start can not be selected
with Drainprogramme.
Select the Start/Pause by pressing
button 
8
To start the selected programme, press
button 
8; the green pilot light stops
flashing.
To interrupt a programme which is
running, press button 
8: the green pilot
light starts to flash.
To restart the programme from the point
at which it was interrupted, press
button 
8again.
If you have chosen a delayed start, the
machine will begin the countdown.
If an incorrect option is selected, an
integrated redpilot light of button 
8
flashes 3 times the message Erris
displayed for a few seconds.
Select the Time Manager option by
pressing buttons 
10
This function allows you to modify the
washing time, automatically proposed
by the washer-dryer.
By pressing this button repeatedly, the
duration of the washing cycle can be
increased or decreased.
A soil level icon will appear on the
display to indicate the chosen degree of
soiling.
(*) We recommend that you reduce the load
sizes (see «Washing programmes»).
Attention!
This option cannot be selected with the
Economy cottons programmes.
The availability of these soil level icons
change according to the type of fabric
as shown in the following chart:
Soil
LevelIconType of fabric
IntensiveFor heavy soiled items
NormalFor normal soiled items
DailyFor daily soiled items
LightFor slightly soiled items
QuickFor very slightly soiled items
Super
Quick (*)For items used or worn for a
short time
FabricSoil Level
CottonsIntensiveNormalDailyLightQuickS. Quick
95°-90°CXXXXXX
60°CXXXXXX
40°CXXXXXX
ColdXXXXXX
Synthetics
Delicates
60°CXXXX
40°CXXXX
40°C XXXX
ColdXXXX
ColdXXXX
use electrolux  15
132961190.qxd  01/09/2008  9.00  Page 15
 
						

							Altering an option or a running
programme
It is possible to change some options
before the programme carries it out.
Before you make any change, you must
pause the washer-dryer by pressing
button 
8.
(Only the 
Time Manager optioncannot
be modified after the programme has
started. )
Changing a running programme is
possible only by resetting it. Turn the
programme selector dial to Oand then
to the new programme position. Start
the new programme by pressing button
8 again. The washing water in the tub
will not be emptied out. 
Interrupting a programme
Press button 
8to interrupt a
programme which is running, the
corresponding light starts to flash. Press
the button again to restart the
programme.
Cancelling a programme
Turn the selector dial to Oto cancel a
programme which is running. You can
now select a new programme.
Opening the door after the
programme has started
First set the machine to pause by
pressing button 
8.
If the light 
9blinks and then goes off,
the door can be opened. 
If the light 
9 remains lit, this means
that the machine is already heating,
that the water level is too high.
In this case the door can not be
opened.
If you cannot open the door but you
need to open it you have to switch the
machine off by turning the selector dial
to O. After a few minutes the door can
be opened (pay attention to the
water level and temperature!).
After closing the door, it is necessary to
select the programme and options
again and press button 
8.
At the end of the programme
The machine stops automatically, the
pilot light of button 
8 goes off and
three blinking «
0.00» will appear on the
display. The buzzer sounds.
If a programme with an option that
ends with water still in the tub has
been selected, the pilot light 
9remains
lit and the door is locked to indicate
that the water must be emptied out
before opening the door.
To empty out the water:
●turn the programme selector dial to
O
●select the Drain or the Spin
programme
●reduce the spin speed if needed, by
pressing the relevant button
●press button 8
At the end of programme, the display
shows 3 flashing zeros «
0.00».the pilot
lights 
9goes off and the door can be
opened.
Turn the programme selector dial to O
to switch the machine off. 
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out
another wash, close the water tap.
Leave the door open to prevent the
formation of mildew and unpleasant
smells.
16electroluxuse
132961190.qxd  01/09/2008  9.00  Page 16
 
						

							drying  electrolux  17
Use - Drying
DRYING ONLY
The recommended loads size is 3 kg
for cottons and linen, and 2 kg for
synthetics.Note! It is also possible
to dry up to 4 kg of cotton items
(see the drying time table).
The water tap must be open and
the drain hose must be positioned
in the sink or connected to the
drain pipe.
1. Load the laundry.
2.  Select the drying programme (for
Cottons or Synthetics in the Drying
sector).
3.  If you wish to select a timed dry-
ing, press button
5until the time
you want appears on the display
(see the drying programmes). Every
time you press this button the dry-
ing time increases by 5 mins. 
Note!
The programme time will automatically
increase by some minutes, this is quite
normal.
4. Press button 
8 to start the pro-
gramme. 
After the programme has started, the
time remaining is updated every
minute.
Note!
The different type of cottons (towelling,
sheets, shirts, and so on) or any
laundry items rolling up during the
spinning phase may result in partial
dryness. In the exceptional case that at
the end of the cycle the laundry
remains slightly wet, we suggest that
you unfold the rolled up items,
redistribute them evenly in the drum
and select an additional drying cycle of
20-30 minutes.
5. At the end of the programme, the
buzzer sounds and three blinking
«
0.00» appear on the display. The
pilot light 
9is on to indicate that the
door is locked.
The last 10 minutes of the drying cycle
correspond to an anti-crease phase.
During this time the door is locked and
the display keeps showing three
flashing zeros «
0.00» 
Note!
If you wish to open the door before or
during the anti-crease phase or to
interrupt it, press any button or turn the
programme selector dial to any pro-
gramme position (except O), the door
can be opened after some minutes
(pilot light 
9is off).
6. Turn the selector dial to the Oposi-
tion to switch the machine off.
Remove the laundry.
Automatic washing and drying 
(NON-STOP programme)
For NON-STOP programmes, the
recommended load size is 3 kg for
cotton and 2 kg for synthetics.
Note! It is also possible also to dry
up to 4 kg of cotton items (see the
drying time table).
Do not use a dosing device/ball
when carrying out a washing &
drying programme.
132961190.qxd  01/09/2008  9.00  Page 17
 
						

							18electrolux drying
1. Load the laundry.
2. Add detergent and fabric softener.
3. Switch the machine on by turning
the selector dial to the selected
washing programme/fabric.
4. Select the required options by
pressing the relevant buttons.
Note!
If possible, do not select a spin speed
lower than that proposed by the appli-
ance to avoid too long a drying time
therefore saving energy.
In any case the reduction of the spin
speed is only possible after selecting
drying. 
The lowest values you can select are
the following:
- 900 r.p.m. for cottons and 700
r.p.m. for synthetics with timed
drying 
5. Select the drying time by pressing
button 
5. The display shows the
entire duration of the washing and
the selected drying cycle.
6. Start the programme by pressing
button 
8. After the programme has
started, the time remaining is
updated every minute.
7. At the end of the programme turn
the selector dial to the Oposition to
switch the machine off.
8. Remove the laundry.
132961190.qxd  01/09/2008  9.00  Page 18
 
						

							washing hints and drying hintselectrolux  19
Washing and Drying hints
Sorting the laundry
Follow the wash code symbols on
each garment label and the
manufacturer’s washing instructions.
Sort the laundry as follows: whites,
coloureds, synthetics, delicates,
woollens.
Temperatures
Before loading the laundry
Never wash whites and coloureds
together. Whites may lose their
“whiteness” in the wash.
New coloured items may run in the first
wash; they should therefore be washed
separately the first time.
Make sure that no metal objects
are left in the laundry (e.g. hair
clips, safety pins, pins).
Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any
belts or long tapes.
Remove persistent stains before
washing. 
Rub particularly soiled areas with a
special detergent or detergent paste.
Treat curtains with special care.
Remove hooks or tie them up in a bag
or net.
Avoid drying dark clothes with light
coloured fluffy items such as towels as
these can attract the fluff.
Remove the laundry when the appli-
ance has finished drying.
To avoid a static charge when drying is
completed, use either a fabric softener
when you are washing the laundry or a
fabric conditioner specifically for tumble
dryers.
Particularly delicate items such as syn-
thetic curtains, woollen and silk,  gar-
ments with metal inserts, nylon stock-
ings, bulky garments such as anoraks,
bedcovers, quilts, sleeping bags and
duvets must not be machine dried.
Garments padded with foam-rubber or
materials similar to foam-rubber must
not be machine dried; they represent a
fire hazard.
Also, fabrics containing residues of set-
ting lotions or hair sprays, nail solvents
or similar solutions must not be
machine dried in order to avoid the for-
mation of harmful vapours.
For drying, follow the indications given
on the manufacturer’s labels.
May be tumble dried
Drying at high temperature
Drying at reduced temperature
Do not tumble dry
90°/95°
for normally soiled white
cottons and linen (e.g. tea
cloths, towels, tablecloths,
sheets...)
50°/60°
for normally soiled, colour
fast garments (e.g. shirts,
night dresses, pyjamas....) in
linen, cotton or synthetic
fibres and for lightly soiled
white cotton (e.g.
underwear).
Cold/30°
/40°
for delicate items (e.g. net
curtains), mixed laundry
including synthetic fibres and
woollens bearing the label
«pure new wool, machine
washable, non-shrink».
132961190.qxd  01/09/2008  9.00  Page 19
 
						

							20electroluxwashing hints and drying hints
Important
As a dryer, the machine works on the
condensation principle.
Therefore, the water tap must be
open and the drain hose must drain
water into a sink or into the drain
pipe, even during the drying cycle.
Maximum loads
Recommended loads are indicated in
the programme charts.
General rules:
Cotton, linen:drum full but not too
tightly packed;
Synthetics:drum no more than half
full;
Delicate fabrics and woollens:drum
no more than one third full.
Washing a maximum load makes the
most efficient use of water and energy.
For heavily soiled laundry, reduce the
load size.
Laundry weights
The following weights are indicative:
Removing stains
Stubborn stains may not be removed
by just water and detergent. It is
therefore advisable to treat them prior
to washing.
Blood:treat fresh stains with cold
water. For dried stains, soak overnight
in water with a special detergent then
rub in the soap and water.
Oil based paint:moisten with benzine
stain remover, lay the garment on a
soft cloth and dab the stain; treat
several times.
Dried grease stains:moisten with
turpentine, lay the garment on a soft
surface and dab the stain with the
fingertips and a cotton cloth.
Rust:oxalic acid dissolved in hot water
or a rust removing product used cold.
Be careful with rust stains which are
not recent since the cellulose structure
will have already been damaged and
the fabric tends to hole.
Mould stains:treat with bleach, rinse
well (whites and fast coloureds only).
Grass:soap lightly and treat with
bleach (whites and fast coloureds only).
Ball point pen and glue:moisten with
acetone (*), lay the garment on a soft
cloth and dab the stain.
Lipstick:moisten with acetone as
above, then treat stains with
methylated spirits. Remove any
residual marks from white fabrics with
bleach.
Red wine: soak in water and
detergent, rinse and treat with acetic or
citric acid, then rinse. Treat any residual
marks with bleach.
1200 gbathrobe 
100 gnapkin
700 gquilt cover
500 gsheet
200 gpillow case
250 gtablecloth
200 gtowelling towel
100 gtea cloth
200 gnight dress
100 gladies’ briefs
600 gman’s work shirt
200 gman’s shirt
500 gman’s pyjamas
100 gblouse
100 gmen’s underpants
132961190.qxd  01/09/2008  9.00  Page 20