Electrolux Eww 167580 W User Manual

1. Open the pump door.
2. Put a container below the recess of the
drain pump to collect the water that
flows out.
3. Press the two levers and pull forward
the drainage duct to let the water flow
out.
4. When the container is full of water, put
the drainage duct back again and emp-
ty the container. Do steps 3 and 4
again and again until no more water
flows out from the drain pump.
5. Pull back the drainage duct.
6. Unscrew the filter and remove it.
12
7. Remove fluff and objects from the
pump.
8. Make...

refitting the pump cover, ensure it is se-
curely re-tightened so as to stop leaks and
young children being able to remove it.
CLEANING THE WATER INLET
FILTERS
If you notice that the machine is taking lon-
ger to fill, check that the filter in the water
inlet hose is not blocked.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter in the hose using a hard
bristle brush.
4. Screw the hose back onto the tap.
5. Unscrew the hose from the machine.
Keep a rug nearby because some...

WHAT TO DO IF…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engi-
neer. Before contacting your local Service
Centre, please carry out the checks listed
below.
During machine operation it is possible that
the red pilot light of button 8 blinks, one of
the following alarm codes appears on the
display and some acoustic signals soundevery 20 seconds to indicate that the ma-
chine is not working:
•
 : problem with the water supply.
•...

ProblemPossible cause/Solution
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fit-
tings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The filter has not been properly screwed...

ProblemPossible cause/Solution
The machine does not dry
or does not dry properly: The drying time or the dryness degree has not been selected.
• Select the drying time or the dryness degree.
The water tap is not turned on. 
• Open the water tap.
The drain filter is clogged. 
• Clean the drain filter.
The machine is overloaded.
• Reduce the laundry load in the drum.
The selected drying programme, time or dryness degree was not
suitable for the laundry.
• Select the suitable drying programme, time or...

Energy consumption in kWh, using
normal 60° C cotton programme(the actual energy consumption de-
pends on the use of the machine)1.19
Washing performance(on scale from A to G, where A - higher
and G - lower performance)A
Spin drying performance(on scale from A to G, where A - better
and G - worse)A
Residual humidity normal 60° C
cotton programme%44
Maximum spin speed on normal
60° C cotton programmerpm1600
Wash load on normal 60° C cotton
programmekg7
Water consumption on normal 60°
C cotton...

ProgrammeEnergy consumption
(KWh)Water consumption
(litres)Programme duration
(Minutes)
Cotton Energy Saving
Programme 60° 1)1.1945
Cottons 40°0.7558
Synthetics 40°0.5551
Delicates 40°0.5563
Wool/ Handwash 30°0.2558
1) «Cotton Energy Saving programme » at 60°C with a load of 7 kg is the reference programme for the data entered
in the energy label, in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it
may vary depending on the...

4. Slide out the relevant plastic spacers.
5. Open the porthole and remove the pol-
ystyrene block fitted on the door seal.
6. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag con-
taining the instruction booklet.
POSITIONING
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets, rugs
etc. Check that the machine does not
touch the wall or other kitchen units. Level
the washing...

2. The other end of the inlet hose which
connects to the machine can be turned
as showed in the picture.
Do not place the inlet hose downwards.
Angle the hose to the left or right de-
pending on the position of your water
tap.
45°
35°
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,...

ELECTRICAL CONNECTION
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
Check that your domestic electrical installa-
tion can take the maximum load required,
also taking into account any other applian-
ces in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept
any responsibility for damage orinjury through failure to comply
with the above safety precaution.
The power supply cable must be
easily accessible after...