Electrolux Eww 148540 W User Manual

							Warning!
1. Disconnect the mains plug from
the mains socket.
2. Do not remove the filter while the
appliance operates. Do not clean
the drain pump if the water in the
appliance is hot. The water must
be cold before you clean the drain
pump.
To clean the drain pump:
1. Open the pump door.
2. Put a container below the recess of the
drain pump to collect the water that
flows out.
3. Press the two levers and pull forward
the drainage duct to let the water flow
out.
4. When the container is full of water, put
the drainage duct back again and emp-
ty the container. Do steps 3 and 4
again and again until no more water
flows out from the drain pump.
5. Pull back the drainage duct.6. Unscrew the filter and remove it.
12
7. Remove fluff and objects from the
pump.
8. Make sure that the impeller of the
pump can turn. If this does not occur,
contact the service centre.
9. Clean the filter under the water tap and
put it back in the pump into the special
guides.
10. Make sure that you tighten correctly the
filter to prevent leakages.
21
electrolux 21
 
						

							11. Close the drain pump door.
Warning!
Never remove the pump cover during a
wash cycle, always wait until the appliance
has finished the cycle, and is empty. When
refitting the pump cover, ensure it is se-
curely re-tightened so as to stop leaks and
young children being able to remove it.
CLEANING THE WATER INLET
FILTERS
If you notice that the machine is taking lon-
ger to fill, check that the filter in the water
inlet hose is not blocked.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter in the hose using a hard
bristle brush.
4. Screw the hose back onto the tap.
5. Unscrew the hose from the machine.
Keep a rug nearby because some wa-
ter may flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
7. Screw the hose back to the machine
and make sure the connection is tight.
8. Turn on the water tap.
EMERGENCY EMPTYING OUT
If the appliance cannot drain the water, pro-
ceed as follows to empty out the machine:
1. pull out the plug from the power sock-
et;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4. open the pump door;
5. place a container on the floor below the
recess of the drain pump;
6. press the two levers and pull forward
the drainage duct to let the water flow
out;
7. when the container is full of water, put
the drainage duct back again and emp-
ty the container;
repeat this operation until water stops
flowing out;
8. if necessary clean the pump (refer to
the section ‘Drain pump’ );
9. close the drain pump door.
When you drain the water with the emer-
gency drain procedure, you must activate
again the drain system:
1. Put 2 litres of water in the main wash
compartment of the detergent dispens-
er.
2. Start the programme to drain the wa-
ter.
FROST PRECAUTIONS
If the machine is installed in a place where
the temperature could drop below 0°C, re-
move the remaining water from the inlet
hose and the drain pump.
1. disconnect the mains plug from the
mains socket.
2. close the water tap
3. unscrew the water inlet hose from the
tap;
4. put the two ends of the inlet hose in a
container and let the water flow out of
the hose.
5. empty the drain pump as described in
the ‘Emergency drain’ section.
6. when the drain pump is empty, install
the water inlet hose again.
Warning!
22 electrolux
 
						

							Make sure that the temperature is more
than 0 °C before you use the appliance
again.
The manufacturer is not responsible for
damages caused by low temperatures.Note!
This appliance is made for use in normal in-
side temperature. The manufacturer is not
responsible for freezing damages.
WHAT TO DO IF…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engi-
neer. Before contacting your local Service
Centre, please carry out the checks listed
below.
During machine operation it is possible that
the red pilot light of button 8 blinks, one of
the following alarm codes appears on the
display and some acoustic signals soundevery 20 seconds to indicate that the ma-
chine is not working:
•
 : problem with the water supply.
•
 : problem with the water draining.
•
 : door open.
Once the problem has been eliminated,
press the button 8 to restart the pro-
gramme. If after all checks, the problem
persists, contact your local Service Centre.
ProblemPossible cause/Solution
The washing machine does
not start:
The door has not been closed. • Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and/or the button 8
has not been pressed.
• Please turn the selector dial and press the button 8 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay
start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The machine does not fill:
The water tap is closed. • Open the water tap.
The inlet hose is squashed or kinked. 
• Check the inlet hose connection.
The filter in the inlet hose or in the inlet valve filter are blocked.
• Clean the water inlet filters (see ‘Cleaning the water inlet filters’
for more details).
The door is not properly closed. 
• Close the door firmly.
The machine fills then emp-
ties immediately:The end of the drain hose is too low.
• Refer to relevant paragraph in «Water drainage» section.
electrolux 23
 
						

							ProblemPossible cause/Solution
The machine does not
empty and/or does not
spin:
The drain hose is squashed or kinked. • Check the drain hose connection.
The drain filter is clogged. 
• Clean the drain filter.
An option or a programme that ends with the water still in the tub
or that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fit-
tings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The filter has not been properly screwed in after cleaning action.
• Screw the filter fully in.
Unsatisfactory washing re-
sults:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the door is released.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redis-
tributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not evenly distrib-
uted in the drum, the machine will not spin. In this case, redistrib-
ute the load manually and select the spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
24 electrolux
 
						

							ProblemPossible cause/Solution
The machine makes an un-
usual noise:The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor en-
sures a softer start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of the machine.
No water is visible in the
drum:Machines based on modern technology operate very economically
using very little water without affecting performance.
The machine does not dry
or does not dry properly: The drying time or the dryness degree has not been selected.
• Select the drying time or the dryness degree.
The water tap is not turned on. 
• Open the water tap.
The drain filter is clogged. 
• Clean the drain filter.
The machine is overloaded.
• Reduce the laundry load in the drum.
The selected drying programme, time or dryness degree was not
suitable for the laundry.
• Select the suitable drying programme, time or dryness degree
for the laundry.
 The laundry is full of differ-
ent colored fluff:The fabrics washed in the previous cycle released fluff of a differ-
ent color .
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum run the special
programme to clean it (refer to “FLUFF IN THE FABRICS” for more
details).
If you are unable to identify or solve the
problem, contact our service centre. Before
telephoning, make a note of the model, se-
rial number and purchase date of your ma-
chine: the Service Centre will require this
information.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ...
TECHNICAL DATA
DimensionsWidth
Height
Depth60 cm
85 cm
63 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water Supply PressureMinimum
Maximum0,05 MPa
0,8 MPa
Level of protection against ingress of solid particles and moistureIPX4
Maximum LoadCotton8 kg
Maximum Dry LoadCotton
Cotton Big Capacity
Synthetic4 Kg
6 Kg
3 Kg
Spin SpeedMaximum1400 rpm
electrolux 25
 
						

							SPECIAL ACCESSORIES FOR INSTALLATION
RUBBER FEET KIT (4055126249)
Available from your authorized dealer.
The rubber feet are particularly recommen-
ded on floating, slippery and wooden floors.
Mount the rubber feet to prevent vibration,
noises and displacement of the appliance
during operation.
Read carefully the instructions supplied with
the kit.FIXING PLATE KIT (405517114)
Available from your authorized dealer.
If you install the appliance on a plinth, se-
cure the appliance in the fixing plates.
Follow the instructions supplied with the kit.
INSTALLATION
UNPACKING
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices
so that they can be refitted if the machine
ever has to be transported again.
1. After removing all the packaging, care-
fully lay machine on it’s back to remove
the polystyrene base from the bottom.
2. Remove the power supply cable and
the draining hose from the hose holders
on the rear of the appliance.
3. Unscrew the three bolts.
4. Slide out the relevant plastic spacers.
5. Open the porthole. Remove the poly-
styrene block fitted on the door seal.
Remove from the drum the objects
supplied with the machine.
1 2
26 electrolux
 
						

							6. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag con-
taining the instruction booklet.
POSITIONING
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets, rugs
etc. Check that the machine does not
touch the wall or other kitchen units. Level
the washing machine by raising or lowering
the feet. The feet may be tight to adjust as
they incorporate a self locking nut, but the
machine MUST be level and stable. If nec-
essary, check the setting with a spirit level.
Any necessary adjustment can be made
with a spanner. Accurate levelling prevents
vibration, noise and displacement of the
machine during operation.
Caution! Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
WATER INLET
An inlet hose is supplied and can been
found inside the machine drum. Do not use
the hose from your previous machine to
connect to the water supply.
This appliance must be connected
to a cold water supply.
1. Connect the hose with the angled con-
nection to the machine.
2. Do not place the inlet hose downwards.
Angle the hose to the left or right de-
pending on the position of your water
tap.
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
WATER DRAINAGE
The end of the drain hose can be posi-
tioned in three ways.
•Hooked over the edge of a sink using
the plastic hose guide supplied with the
machine. In this case, make sure the end
cannot come unhooked when the ma-
chine is emptying. This could be done by
45°
35°
electrolux 27
 
						

							tying it to the tap with a piece of string or
attaching it to the wall.•In a sink drain pipe branch. This
branch must be above the trap so that
the bend is at least 60 cm above the
ground.
•Directly into a drain pipe at a height of
not less than 60 cm and not more than
90 cm. The end of the drain hose must
always be ventilated, i.e. the inside diam-
eter of the drain pipe must be larger than
the outside diameter of the drain hose.
The drain hose must not be kinked.
The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local Service Centre.
ELECTRICAL CONNECTION
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
Check that your domestic electrical installa-
tion can take the maximum load required,
also taking into account any other applian-
ces in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept
any responsibility for damage orinjury through failure to comply
with the above safety precaution.
The power supply cable must be
easily accessible after installing the
machine.
Should the appliance power supply
cable need to be replaced, this
must be carried out by a Service
Centre.
ENVIRONMENT CONCERNS
The symbol  on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise becaused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
PACKAGING MATERIALS
The materials marked with the symbol 
are recyclable.
28 electrolux
 
						

							>PEPSPP
						

							30 electrolux