Electrolux Ews 86110 W User Manual

							2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
3. Unscrew the three bolts.
4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two
large ones with the corresponding plas-
tic plug caps supplied in the bag con-
taining the instruction booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets, rugs
etc. Check that the machine does not
touch the wall or other kitchen units. Level
the washing machine by raising or lowering
the feet. The feet may be tight to adjust as
they incorporate a self locking nut, but the
machine MUST be level and stable. If nec-
essary, check the setting with a spirit level.
Any necessary adjustment can be made
with a spanner. Accurate levelling prevents
electrolux 21
 
						

							vibration, noise and displacement of the
machine during operation.
Caution! Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
Water inlet
Warning! This appliance must be
connected to a cold water supply.
1. Connect the water inlet hose supplied
with the machine to a tap with a 3/4
thread. Always use the hose supplied
with the appliance.
Important! Do not use the hose from
your previous machine to connect to
the water supply.2. The other end of the inlet hose which
connects to the machine can be turned
as showed in the picture.
Do not place the inlet hose downwards.
Angle the hose to the left or right de-
pending on the position of your water
tap.
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
Important! Before connecting up the
machine to new pipework or to pipework
that has not been used for some time, run
off a reasonable amount of water to flush
out any debris that may have collected in
the pipes.
Water drainage
The end of the drain hose can be posi-
tioned in three ways.
•Hooked over the edge of a sink using
the plastic hose guide supplied with the
machine. In this case, make sure the end
cannot come unhooked when the ma-
chine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.
22 electrolux
 
						

							•In a sink drain pipe branch. This
branch must be above the trap so that
the bend is at least 60 cm above the
ground.
•Directly into a drain pipe at a height of
not less than 60 cm and not more than
90 cm. The end of the drain hose must
always be ventilated, i.e. the inside diam-
eter of the drain pipe must be larger than
the outside diameter of the drain hose.
The drain hose must not be kinked.
The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local Service Centre.
electrolux 23
 
						

							24  electrolux 
Electrolux.CI37\¼3‚
=ðb] ™öelectrolux.com 
I}e“
.#÷j—Jt 24
 26
66$Åiñ: 27
 29
8t0ÇG· 29.uG·9&KÉT–6_KÉ 31 
?¦LšZ÷ 33
lk™T–@”Aã 36
7Ôi+6!hó 40
5Zâ_V8( 44
,9˜^9ƒ2ä œ&uZÛb©Jt
.#÷j—Jt
d\\j—JtÝ]Z]h@!t š_V\™è µ,4(lN0!t
*8t2&RR’í
z374
						

							  electrolux   25
zG
						

							26  electrolux 

374
						

							  electrolux   27
?¦Aã% *ú#ÔIa
G
						

							28  electrolux 
 œSº>Ã
c7V=ócj”2è4Ï9˜Sº>Ãi>DcŒ9’ë=ñè µh,Z6!>Ãè
!t#ÜZòDøG±G®II7	í,9˜9ß_yÃbÁZÛbÝ>Ãí
 œ6!>Ã
c7V=
						

							  electrolux   29

z
%d!ëí
z
z.– 2 #
						

							30  electrolux 
L