Electrolux Ews 126510 W User Manual

user manual
Washing Machine
EWS 126510 W
 

Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information   2
Product description   4
Control panel   5
First use   8
Personalisation  8
Daily use   8
Helpful hints and tips   11
Washing programmes   13Care and cleaning   15
What to do if…   19
Technical data   21
Consumption values   22
Installation  22
Electrical connection   25
Environment concerns   25
Subject to change without notice
 SAFETY INFORMATION
Important! Read carefully & keep for future...

INSTALLATION
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check
that it is not damaged. If in doubt, do not
use it and contact the Service Centre.
• All packing and transit bolts must be re-
moved before use. Serious damage can
occur to the product and to property if
this is not adhered to. See relevant sec-
tion in the user manual.
• After having installed the appliance,
check that it is not standing on the inlet
and drain hose and the worktop is not...

PRODUCT DESCRIPTION
Your new appliance meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption. Its new washing system allows to-
tal use of detergent and reduces water consumption so saving energy.
4
5
12
3
6
1Detergent dispenser drawer
2Control panel
3Door opening handle
4Rating Plate
5Drain pump
6Adjustable feet
DETERGENT DISPENSER DRAWER
 Compartment for detergent used for
prewash and soak phase or for stain re-
mover used during the stain...

2. Put in the new programme guide.
CONTROL PANEL
Below is a picture of the control panel. It shows the programme selector dial as well as
the buttons, pilot lights and the display. These are presented by relevant numbers on
the following pages.
123456789
1Programme selector dial
2Display
3TEMPERATURE button
4SPIN reduction button
5PREWASH button
6EXTRA RINSE button
7DELAY START button
8START/PAUSE button
9TIME MANAGER buttons
PROGRAMME SELECTOR DIAL
It allows you to switch the appliance on/off
and/or to...

DISPLAY
2.12.22.32.42.52.62.72.82.9
2.122.112.10
The display shows the following informa-
tion:
2.1:Temperature value
2.2: Temperature icons 
 , Cold  .
During the washing cycle the display shows
the temperature icon animated to indicate
that the appliance has started the heating
phase of the water in the tub.
2.3: Spin value
2.4: Spin speed icons.
•
No spin 
•
Rinse Hold 
•
Night Cycle 
During the spinning phase the spiral is ani-
mated.
No spin option eliminates all the spin pha-
ses and increases the...

In the event of operating problems, some
alarm codes can be displayed, for exam-
ple 
 (see paragraph «What to do
if...»).
•Delay Time value
2.10: Soil degree icons
•
Intensive 
•
Normal 
•
Daily 
•
Light 
•
Quick 
•
Super Quick 
•
Refresh 
•
Super Refresh 
(see paragraph «Select Time Manager op-
tion»).
2.11: Clock icon 
After the programme has started, the dura-
tion is displayed and the clock icon is ani-
mated.
2.12: Washing programme phase icons
By selecting the wash programme, the
washing programme...

 +/-= Time Manger buttons
FIRST USE
• Ensure that the electrical and water
connections comply with the installa-
tion instructions.
• Ensure that the drum is empty.
• Pour 2 liters of water into the main
wash compartment 
 of the deter-
gent drawer in order to activate the
ECO valve. Then run a cotton cycleat the highest temperature without
any laundry in the machine, to re-
move any manufacturing residue
from the drum and tub. Pour 1/2 a
measure of detergent into the main
wash compartment and start the...

must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
SELECT THE REQUIRED PROGRAMME
BY TURNING THE PROGRAMME
SELECTOR DIAL (1)
Turn the programme selector dial to the re-
quired programme. The washing machine
will propose a temperature and automati-
cally select the maximum spin value provi-
ded for the programme you have chosen.
You can change these values by operating
the corresponding buttons. The green pilot
light of the button 8 starts to flash.
The selector dial can be turned...

Cancelling the delayed start after having
pressed button 8:
1. Set the washing machine to PAUSE by
pressing button 8.
2.
Press button 7 once until the symbol 
’ is displayed
3. Press button 8 again to start the pro-
gramme.
Important! The selected delay can be
changed only after selecting the washing
programme again.
The Delay Start can not be selected with
DRAIN programme.
START THE PROGRAMME BY
PRESSING BUTTON 8
To start the selected programme, press the
button 8, the green pilot light of the button
8...