Electrolux Ews 1250 Instruction Manual

							1 22
If you are unable to identify or solve the problem,contact our service centre. Before telephoning, make a note
of the model, serial number and purchase date of your machine:  the Service Centre will require this information.
Contents of this user manual may be modified without informing you.
Water is not
visible in the machine? The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption. Performance is
nevertheless excellent.
The machine makes an unusual
noise? The machine is fitted with a commutator
motor which improves machine
performance.Possible cause Problem
Spinning starts late or the laundry
is not spun enough :
The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum.The laundry is redistributed by reverse
rotation of the drum.This may happen several times
before the unbalance disappears and normal spinning
can resume.if ,after few minutes,the laundry is still
not evenly distributed in the drum,the machine will
spin at a lower speed or will not spin.If at the end of
the programme the laundry is not spun enough,
redistriute the load manually and select the spin
programme.
The door can not open :
The program is still running and the drum is turning.
The door lock has not yet released.
The water level is above the bottom edge of the door.
The machine is heating the water, and the water
temperature is higher than 55The door can only be opened when the relevant light
has gone out.
 
						

							221
Something not working?Problems which you can resolve yourself
During machine operation it is possible that one of the End light starts to flash:
Possible cause Problem
The door is not firmly closed.
E40
The machine is not plugged in or there is no power at
the socket.
The main fuse or the fuse in the plug has blown.
The START/PAUSE button has not been pressed.
The DELAY option has been selected.
The machine does not start up:
The machine fills them empties
 immediately: The machine does not fill:
The water tap is closed.
E10
The inlet hose is squashed or kinked.
E10
The filter in the inlet hose is blocked.
E10
The door is not properly closed.
E40
The end of the drain hose is too low. Refer to relevant
paragraph in drainage section.
The machine does not empty and/or
does not spin:
There is water on the floor:
Unsatisfactory washing results:
The drain hose is squashed or kinked.
E20
The drain pump is clogged.
E20
The laundry is not evenly distributed in the drum.
The RINSE HOLD or NIGHT CYCLE option has been
selected.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose ; check to see if it is
damp.
The drain hose is damaged.
Check that the filter has been fastened.
Too little detergent or unsuitable detergent has Been
used.
Stubborn stains have not been treated prior to washing.
The correct program or temperature was not  selected.
Excessive laundry load.
The transit bolts and packing have not been removed.
The support feet have not been adjusted.
The laundry in drum has not been evenly distributed.
Too little laundry is washed.
Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If
after all checks, the problem persists, contact your local Service Centre.The machine vibrates or is noisy:E10:problem with the water supply
E20: problem with the water draining
E40:door open-
-
-
34    4    4    5
55566778
1919191919202020
21-22      18
8121212121212131312
15 - 17
77
            8
14
 
						

							3 20
Screw the pump fully in.
Close the pump door.
If the machine is installed in a place where the tem-
perature could drop below 0
, proceed as follows:
7. Frost precautionsRemove the plug from the socket.
Close the water tap and unscrew the water inlet hose
from the tap.
Place the end of the emergency emptying hose and
that of the inlet hose in a  bowl placed on the floor
and let water drain out.
Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap
on again.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.When
you use the machine again, make sure that the ambi-
ent temperature is above 0
. Remove any objects from the pump impeller by
rotating it.
Put the cap back on the emergency emptying hose
and place the latter back in its seat.Turn off the water tap.
Take off the inlet hose from water tap. Drain water in
this hose.
Unscrew the hose from the inlet valve.
Clean the filter with a stiff brush.
Put on the hose back onto the tap and the inlet
valve.5. Water inlet filterIf you notice that the machine is taking longer to fill,
check that the filter in the water inlet valve is not
blocked:
Clean the pump if necessary as previously described.
Replace the emergency emptying hose in its seat
after having plugged it.
Screw the pump again and close the door.If the water is not discharged , proceed as follows to
empty out the machine:6. Emergency emptying outPull out the plug from the power socket;
Close the water tap;
If necessary, wait until the water has cooled down;
Open the pump door;
Place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove
its cap. The water should drain by gravity into the
bowl.Whe the bowl is full,put the cap back on the
hose. Empty the bowl. Repeat the procedure until
water stops flowing ou;
 
						

							19 4
        85 cm        60 cm       49 cm
5    kg
2    kg
2    kg
1    kg
2    kg
1000 1200 1200 
EWS1050
EWS1250
EWS1250Z
    0.05MPa    0.8MPaAC 220V/50Hz
2000 W
10A
PEPSPP
MaintenanceCheck from time to time the door seal and eliminate
eventual possible objects that could be trapped in the
fold.1. Door sealAfter a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the machine,
press the button in the rear left-hand corner.To facili-
tate cleaning, the top part of the additive compart-
ment can be removed.3. Detergent dispenser drawerClean the outside of the machine with warm water and
a neutral, non-abrasive household detergent. Rinse
with clean water and dry with a soft cloth.2. BodyworkImportant: do not use methylated spirits, solvents or
similar products to clean the bodywork.
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the drawer
after cleaning.
The drain pump should be inspected if4. Drain pumpThe machine does not empty and/or spin.
The machine makes an unusual noise during draining
due to objects such as safety pins,coins etc.
blocking the pump.
Disconnect the appliance.
If necessary wait until the water has cooled down.
Open the pump door.Place a container close to the pump to collect any
spillage.
Release the emergency emptying hose, place it in
the container and remove its cap.
When no more water comes out, unscrew the pump
and remove it. Always keep a rag nearby to dry up
spillage of water when removing the pump.Proceed as follows
 
						

							18
Programme  table
Type of laundry
and symbols on
labelsProgramme/
temperatureDescription of
programmeAvailable options Max load
Wash at 60-30or cold three rinses
long spin Coloured cotton:
e.g.shirts,blouse
underwear
towels
household linenCottons
60-30
cold 
5Kg
Wash at 60-30
,
or cold 
three rinses
Short spin Synthetic
fabricand
blends:
e.g.shirts,blouse,
underwearSynthetic
60-30
cold 
2Kg
Wash at 40-30
,
or cold 
three rinses
Short spin Delicate fabric
e.g. acrylic fabric,
viscose, polyester,
synthetic blendsDelicates
40 -30
cold 
2Kg
Wash at 40-30
,
or cold 
three rinses
Short spin Wool,hand
wash
Wool/Hand
wash
40 - 30cold 
1Kg
Wash at 30
,
or cold 
three rinses
Short spin Silksilk
 30
cold 
2Kg Spin speed
Rinse hold
Night cycle
Economy
Super Quick wash
Prewash
Anti-allergic rinse Wash at 60-95
three rinses
long spin white cotton:
e.g. : work clothes,
sheet,household
linen, table clothCottons
60-95
5Kg
60
95
60
30
4060
Spin speed
Rinse hold
Night cycle
Economy
Super Quick wash
Prewash
Anti-allergic rinse
Spin speed
Rinse hold
Night cycle
Economy
Super Quick wash
Prewash
Anti-allergic rinse
Spin speed
Rinse hold
Night cycle
Super Quick wash
Prewash
Anti-allergic rinseSpin speed
Rinse hold
Night cycle
3030
40
30
Spin speed
Rinse hold
Night cycle
5 6
1234
7
5
A
B
A
B
C
B
 
						

							617
12. How to cancel a programme dur-
ing its cycleTo cancel a programme that is being carried out, first
pause the washing machine by pressing theSTART/
PAUSE button, then press the SKIP RESET button
repeatedly, until the display shows three blinking
dashes.13.How to Open the door during the
cycle of a programmeYou can open the door, after having set the washing
machine to PAUSE, provided the following conditions
exist:
The washing machine is not in the heating phase
beyond 55°C;
The level of the water is not high;
The drum is not turning.
If these requirements are met, when you pause the
washing machine, the door can be opened instantly.
Should it not be possible to open the door, and should
it be absolutely necessary to do so, switch the ma-
chine off by pressing the ON/OFF button. After ap-
proximately 3 minutes, you can open the door instantly.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the ON/OFF but-
ton again, the washing machine will resume the
programme from the point where it had been interrupted.14. End of programme
If you had selected the RINSE HOLDor NIGHT CYLCE
option , the light of the START/PAUSE button goes out,
the zero on the display begins to flash, the door is
locked and RINSE HOLD or NIGHT CYCLE light re-
mains lit.
When the programme has been completed, a blinking
zero appears on the display and the audible signal is
given.
Press the SKIP RESET button repeatedly to erase
the programme that has just been carried out. If
you omit to do this, the next time you switch the
washing machine on, the blinking zero will ap-
pear on the display and you will hear the audible
signal.
Press the ON/OFF button to switch the machine off.
The relevant light will go out. Remove the laundry
from the washing machine. Check whether the drum is
completely empty, by rotating it with your hand. The
purpose of this is to prevent any items of laundry
from remaining accidentally in the drum, where they
might get damaged in a subsequent wash (e.g. by
shrinking) or bleed colour into another load of laundry.
We advise you to close the water supply tap and
disconnect the plug from the socket. Leave the door
ajar in order to air the washing machine.
60cm
220V/50Hz
60
90cm
At the end of the programme, the washing machine
stops automatically, gives an audible signal, and dis-
plays a blinking zero.
 
						

							167
123456
7. Select the SPIN SPEED or the RINSE
HOLD optionPress the SPIN SPEED button repeatedly, in order to
select the desired spin speed or the RINSE HOLD
option. The relevant light will light up. If you select the
RINSE HOLD option, the machine will stop at the end
of the programme with the water still in the tub.8. Select the desired optionsIf your laundry is very dirty or has stubborn stains, it
may be advisable to select the PREWASH, ANTI-
ALLERGIC RINSE option. Press the OPTIONS button
so as to cause one or both of the lights to light up. If
your laundry is only slightly soiled, depress ECONOMY
or SUPER QUICK WASH button. The relevant light
illuminates.9.Select the DELAY START
 delay. The selected delay time value (up to 23 hours)
will appear on the display for 3 seconds, then the
duration of the programme will appear again.10. Start the programmePress the START/PAUSE button. The relevant light will
stop flashing and only the light relevant to the phase
that is in progress will remain lit. If you have chosen a
delayed start, the washing machine will begin the count-
down The display will show the duration of the
programme or the selected delay.
Important!
Every programme has its limited spin speed in order to
preventing laundry from being spoiled,so it’s normal
that some speed can not be chosed. Important!
Every programme has its limited temperature in order
to preventing laundry from being spoiled,so it’s normal
that some temperature can not be chosed.
Before you start the programme, if you wish the
starting to be delayed, press the DELAY START button
repeatedly, or keep it pressed, to select the desired
11. How to change a programm e dur-
ing its cyclePAUSE the machine by pressing the START/PAUSE
button;
Press the SKIP RESET button repeatedly, until only
the DRAIN light remains lit;
Press the START/PAUSE button again. Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button. It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is possible,
obviously, only during the washing phase.
If it is necessary to drain the water in order to change
the programme in progress,proceed as follows:
When the water has been drained, the display shows a
blinking zero. You may now select a new programme
and press the START/PAUSE button to start it.
 
						

							8
/
Operating sequence.
1. Place the laundry in drumOpen the door.
Place the laundry in drum, one item at a time,shaking
them out as much as possible.
Close the door.2. Measure out the detergentPull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment.
If you wish to carry out the prewash, pour detergent
into the appropriate compartment marked.3. Measure out the additivesIf required, pour fabric softener into the compartment
marked, without exceeding the
MAX
mark.
6 . Select temperature
4. Switch the machine on5. Select the desired programme/
fabricPress the FABRICS button repeatedly, in order to
select the desired programme/fabric. The relevant light
will light up. The lights relevant to the phases that form
the programme will light up. The display will show the
duration of the selected programme, calculated on the
basis of the maximum load for each type of fabric.
The light of the START/PAUSE button will start flashing.
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the execution of
the cycle.
Press the TEMPERATURE button if you wish to select
a temperature value different from the one proposed
by the washing machine. The relevant light will light up.
To switch the machine on, press the ON/OFF button :
the mains-on light comes on. The display will show
three blinking dashes or a blinking zero.
15
13
5
4
/
2
/
/
/
245
689
10 11
1
3
12
7
Before washing your first load of laundry we recom-
mend that you run a cotton cycle at 60
 with the
machine empty, in order to remove any manufac-
turing residue from the drum and tub.
 
						

							9
6-7
/
//
/
-
8
/
//
14
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
International wash code symbolsEnergetic
wash
Max. wash
temperature
95
CMax. wash
temperature
60
CMax. wash
temperature
40
CMax. wash
temperature
30
C
Hand washDo not
wash
at all Delicate wash
Bleaching
Bleach in cold waterDo not bleach
lroningDo not iron Lukewarm iron
max 110
C Hot iron
max 200
CWarm iron
max 150
C
Dry cleaningDo not
dry clean Dry cleaning
in petrol,
pure alcohol
and R 113 Dry cleaning
in all solventsDry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
DryingDo not
tumble dry Tumble dry Flat On the lineOn clothes
hangerhigh
temperature
low
temperature
F
P
A
40
95
6060
30
40
30
40
cI
-
-