Electrolux Ews 10770 W User Manual

user manual
Washing Machine
EWS 10770 W - EWS 12770 W
 

Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information    2
Product description    4
Control panel    5
First use    7
Personalisation    7
Daily use    8
Helpful hints and tips    11
Washing programmes    13Care and cleaning    17
What to do if…    21
Technical data    23
Consumption values    23
Installation    24
Electrical connection    27
Environment concerns    27
  Subject to change without notice
 Safety information
Important! Read carefully &...

Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing and transit bolts must be re-
moved before use. Serious damage can
occur to the product and to property if this
is not adhered to. See relevant section in
the user manual.
• After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not...

Product description
Your new appliance meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption. Its new washing system allows total
use of detergent and reduces water consumption so saving energy.
12
3
4
5
6
1Detergent dispenser drawer
2Control panel
3Door opening handle
4Rating Plate
5Drain pump
6Adjustable feet
Detergent dispenser drawer
 Compartment for detergent used for pre-
wash and soak phase or for stain remover
used during the stain...

Programme Chart
Various programme charts in different lan-
guages are supplied with the appliance. One
is on the front side of the detergent dispenser
drawer and the others are attached into theuser manual assy. The chart in the drawer
can be replaced easily: remove the chart
from the drawer by pulling it towards the right
and insert the chart with the language re-
quired.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as
the buttons, pilot lights and...

Start Pause
This button allows you to start or to interrupt
the selected programme.Time Manager
These buttons allows you to modify the pro-
gramme duration automatically proposed by
the appliance.
Display
7.17.37.57.67.77.8
7.9
7.107.117.12
7.27.4
The display shows the following information:
7.1: Temperature value
7.2: Temperature icons 
 , Cold  .
During the washing cycle the display shows
the temperature icon animated to indicate
that the appliance has started the heating
phase of the water in the...

•
Incorrect option selection
If an option which is not compatible with
the set wash programme is selected, the
message Err is displayed at the bottom of
the display for a few seconds and the in-
tegrated red light of button 8 start flashing.
•
Alarm codes
In the event of operating problems, some
alarm codes can be displayed, for example
E20 (see paragraph «What to do if...»).
•Delay Time value
7.9: Clock icon 
After the programme has started, the dura-
tion is displayed and the clock icon is anima-
ted....

also when the washing machine is not work-
ing.
There are two different ways to set this op-
tion:
1.
Before pressing button 8 : it will be im-
possible to start the machine.
2. After pressing button 8 : it will be impos-
sible to change any other programme or
option.To enable or disable this option press simul-
taneously for about 6 seconds buttons 5 and
6 until on the display, the icon 
 appears or
disappears.
Daily use
Load the laundry
Open the door by carefully pulling the door
handle outwards. Place...

select the maximum spin value provided for
the programme you have chosen. You can
change these values by operating the corre-
sponding buttons. The green pilot light of the
button 8 starts to flash.
The selector dial can be turned either clock-
wise or counterclockwise. Turn to position
 to reset programme/Switching the ma-
chine off.
At the end of the programme the selec-
tor dial must be turned to position 
 , to
switch the machine off.
Caution! If you turn the programme
selector dial to another...

To interrupt a programme which is running,
press the button 8 : the green pilot light starts
to blink.
To restart the programme from the point at
which it was interrupted, press the button 8
again . If you have chosen a delayed start,
the machine will begin the countdown.
If an incorrect option is selected, the red pilot
light of the button 8 blinks for 3 times the
message Err is displayed for few seconds.
Select the Time Manager option by
pressing buttons 9
By pressing these buttons repeatedly, the...