Electrolux Ewn 10470 W User Manual

							Technical data
Dimensions Width 60 cm
85 cm
63 cm Height
Depth
Water supply pressure Minimum 0,05 MPa
0,8 MPa Maximum
CottonMaximum Load6kg
MaximumSpin Speed1000 rpm 
Electrical connection
Voltage - Overall power -
FuseInformation on the electrical connection is given
on the rating plate on the inner edge of the
appliance door
technical dataelectrolux  31
132963290_EN.qxd  22/02/2008  10.00  Pagina  31
 
						

							Consumption values
Water
consumption 
(in litres)Programme Energy
consumption 
(in kWh)Programme
duration 
(in minutes)
Cottons 90°2.157
Cottons 60° 1.354
Cottons Eco 60° (*) 1.0246
Synthetics 60°
0.9 46
x
For the duration of the
programmes, please
refer to the display on
the control panel.
Handwash 40° 0.4552 Delicates 40° 0.557
Wool 40° 0.4552
The consumption data shown on this
chart is to be considered purely
indicative, as it may vary depending on
the quantity and type of laundry, on the
inlet water temperature and on the
ambient temperature. It refers to the
highest temperature for each wash
programme.(*) The programme «Cottons Economy»
at 60°C is the reference programme
for the data entered in the energy
label, in compliance with EEC 92/75
standards.
32electroluxconsumption values
132963290_EN.qxd  22/02/2008  10.00  Pagina  32
 
						

							Installation
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit
devices so that they can be refitted if the
machine ever has to be transported
again.
1. After removing all the packaging,
carefully lay machine on it’s back to
remove the polystyrene base from the
bottom.
2. Remove the power supply cable and
the draining hose from the hose
holders on the rear of the appliance.
3. With a suitable spanner unscrew and
remove the central rear bolt A. Slide
out the relevant plastic spacer.


4. Unscrew and remove the two large
rear bolts Band the six smaller bolts
C.
5. Remove the bracket Dand tighten up
the six smaller bolts C.












installationelectrolux  33
132963290_EN.qxd  22/02/2008  10.00  Pagina  33
 
						

							34electroluxinstallation
6. Open the porthole, take out the inlet
hose from the drum and remove the
polystyrene block fitted with the
adhesive tape on the door seal.
7. Fill the smaller upper hole and the two
large ones with the corresponding
plastic plug caps supplied in the bag
containing the instruction booklet.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets,
rugs etc. Check that the machine does
not touch the wall or other kitchen units.
Level the washing machine by raising or
lowering the feet. The feet may be tight
to adjust as they incorporate a self
locking nut, but the machine MUST be
level and stable.
If necessary, check the setting with a
spirit level.
Any necessary adjustment can be made
with a spanner. 
	

Accurate levelling prevents vibration,
noise and displacement of the machine
during operation.Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
Water inlet
An inlet hose is supplied and can been
found inside the machine drum. Do not
use the hose from your previous
machine to connect to the water supply.
1. Open the porthole and extract the
inlet hose.
2. Connect the hose with the angled
connection to the machine.
Do not place the inlet hose
downwards. Angle the hose to the
left or right depending on the
position of your water tap.


132963290_EN.qxd  22/02/2008  10.00  Pagina  34
 
						

							3. Set the hose correctly by loosening
the ring nut. 
After positioning the inlet hose, be
sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied
with the appliance.
The inlet hose must not be lengthened.
If it is too short and you do not wish to
move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
Water drainage
The end of the drain hose can be
positioned in three ways:
Hooked over the edge of a sink
using the plastic hose guide
supplied with the machine.
In this case, make sure the end cannot
come unhooked when the machine is
emptying. This could be done by tying
it to the tap with a piece of string or
attaching it to the wall.

In a sink drain pipe branch.This
branch must be above the trap so that
the bend is at least 60 cm above the
ground. 
Directly into a drain pipe at a
heightof not less than 60 cm and not
more than 90 cm. The end of the drain
hose must always be ventilated, i.e.
the inside diameter of the drain pipe
must be larger than the outside
diameter of the drain hose.
The drain hose must not be kinked.
The drain hose may be extended to a
maximum of 4 metres. An additional
drain hose and joining piece is available
from your local Service Centre.


installationelectrolux  35
132963290_EN.qxd  22/02/2008  10.00  Pagina  35
 
						

							Electrical connection
Information on the electrical connection
is given on the rating plate on the inner
edge of the appliance door.
Check that your domestic electrical
installation can take the maximum load
required, also taking into account any
other appliances in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept
any responsibility for damage or
injury through failure to comply
with the above safety precaution.
The power supply cable must be
easily accessible after installing the
machine.
Should the appliance power supply
cable need to be replaced, this
must be carried out by a Service
Centre. 
36electrolux installation
Permanent connection
In the case of a permanent connection
it is necessary that you install a double
pole switch between the appliance and
the electricity supply (mains), with a
minimum gap of 3 mm between the
switch contacts and of a type suitable
for the required load in compliance with
the current electrical regulations. The
switch must not break the yellow and
green earth cable at any point. This
operation must be performed by a
qualified electrician.
132963290_EN.qxd  22/02/2008  10.00  Pagina  36
 
						

							environment concerns electrolux  37
Environment concerns
Packaging materials
The materials marked with the symbol
are recyclable.
>PEPSPP
						

							38electroluxnotes
132963290_EN.qxd  22/02/2008  10.00  Pagina  38
 
						

							132963290_EN.qxd  22/02/2008  10.00  Pagina  39
 
						

							ANC number: 132 963 290 - 00 - 072008
132963290_EN.qxd  22/02/2008  10.00  Pagina  40